Low Latency 40-Gbps Ethernet Intel® FPGA IP User Guide: Stratix® 10

Download PDF
ID 683600
Date 5/31/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 40G Ethernet Core 2. Stratix® 10 Low Latency 40G Ethernet IP Core Parameters 3. Getting Started 4. Functional Description 5. Reset 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Debugging the Link 9. Ethernet Toolkit Overview 10. Stratix® 10 Low Latency 40GbE IP Core User Guide Archives 11. Differences Between Stratix® 10 Low Latency 40G Ethernet IP Core and Low Latency 40G Ethernet IP Core That Targets an Arria 10 Device 12. Document Revision History for Stratix® 10 Low Latency 40G Ethernet User Guide
1. About the Low Latency 40G Ethernet Core x
1.1. Stratix® 10 LL 40GbE IP Core Supported Features 1.2. Stratix® 10 LL 40GbE Core Device Family and Speed Grade Support 1.3. Resource Utilization 1.4. Release Information
1.2. Stratix® 10 LL 40GbE Core Device Family and Speed Grade Support x
1.2.1. Device Family Support 1.2.2. Stratix® 10 LL 40GbE IP Core Device Speed Grade Support
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the Stratix® 10 LL 40GbE IP Core Parameters and Options 3.3. Simulating the IP Core 3.4. Generated File Structure 3.5. Integrating Your IP Core in Your Design 3.6. Stratix® 10 Low Latency 40G Ethernet IP Core Testbench 3.7. Compiling the Full Design and Programming the FPGA
3.5. Integrating Your IP Core in Your Design x
3.5.1. Pin Assignments 3.5.2. Adding the Transceiver PLL 3.5.3. Clock Requirements for 40GBASE-KR4/CR4 Variations 3.5.4. Adding the External TX MAC PLL 3.5.5. Placement Settings for the Stratix® 10 Low Latency 40G Ethernet Core
3.6. Stratix® 10 Low Latency 40G Ethernet IP Core Testbench x
3.6.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Stratix® 10 LL 40GbE Core Functional Description 4.2. User Interface to Ethernet Transmission
4.1. Stratix® 10 LL 40GbE Core Functional Description x
4.1.1. Stratix® 10 LL 40GbE Core TX MAC Datapath 4.1.2. Stratix® 10 LL 40GbE Core RX MAC Datapath 4.1.3. Link Fault Signaling Interface 4.1.4. Stratix® 10 Low Latency 40GBASE-KR4 IP Core Variations
4.1.1. Stratix® 10 LL 40GbE Core TX MAC Datapath x
4.1.1.1. Frame Padding 4.1.1.2. Preamble Insertion 4.1.1.3. Inter-Packet Gap Generation and Insertion 4.1.1.4. Frame Check Sequence (CRC-32) Insertion
4.1.2. Stratix® 10 LL 40GbE Core RX MAC Datapath x
4.1.2.1. IP Core Preamble Processing 4.1.2.2. IP Core Strict SFD Checking 4.1.2.3. Length/Type Field Processing 4.1.2.4. RX CRC Checking and Dynamic Forwarding
4.1.2.3. Length/Type Field Processing x
4.1.2.3.1. Length Checking
4.2. User Interface to Ethernet Transmission x
4.2.1. Order of Transmission 4.2.2. Bit Order For TX and RX Datapaths
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. Transceivers Signals 6.4. Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals 6.8. Clocks 6.9. Flow Control Interface
7. Control, Status, and Statistics Register Descriptions x
7.1. Stratix® 10 LL 40GBASE-KR4/CR4 Registers 7.2. PHY Registers 7.3. TX MAC Registers 7.4. RX MAC Registers 7.5. Statistics Registers
7.5. Statistics Registers x
7.5.1. TX Statistics Registers 7.5.2. RX Statistics Registers
9. Ethernet Toolkit Overview x
9.1. Features
1. About the Low Latency 40G Ethernet Core
2. Stratix® 10 Low Latency 40G Ethernet IP Core Parameters
3. Getting Started
4. Functional Description
5. Reset
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Debugging the Link
9. Ethernet Toolkit Overview
10. Stratix® 10 Low Latency 40GbE IP Core User Guide Archives
11. Differences Between Stratix® 10 Low Latency 40G Ethernet IP Core and Low Latency 40G Ethernet IP Core That Targets an Arria 10 Device
12. Document Revision History for Stratix® 10 Low Latency 40G Ethernet User Guide

6.9. Flow Control Interface

Flow Control Interface signals become available when you turn on Enable MAC Flow Control in the parameter editor.
Table 22.  Flow Control Signals

Signal Name

Direction

Description

pause_insert_tx0[(FCQN-1):0]

pause_insert_tx1[(FCQN-1):0]

Input

This signal is available if you specify pause on PFC.

The signal indicates to the MAC whether XON or XOFF Pause or PFC flow control frame should be sent.
  • FCQN = 1 for Pause
  • FCQN = 1 ~ 8 for PFC
The request for XON/XOFF flow control frame transmission can be done in either 1 or 2-bit request mode.

1-bit mode request model:

The IP core ignores pause_insert_tx1[(FCQN-1):0].

The following encoding is defined:
  • 0: No request
  • 0 to 1: Generate XOFF request
  • 1: Continue to generate XOFF request
  • 1 to 0: Generate XON request

2-bit mode request model:

The higher-order bit is in pause_insert_tx1[(FCQN-1):0] and the lower-order bit is in pause_insert_tx0[(FCQN-1):0].

The XON/XOFF request is a level-based request.

The following encoding is defined:

  • 00: No further XON/XOFF request. In an XON/XOFF flow control frame is in progress, it is sent.
  • 01: Generate XON flow control frame and continuously sends them thereafter
  • 10: Generate XOFF flow control frame and continuously sends them thereafter
  • 11: Invalid request
pause_receive_rx[(FCQN-1):0] Output

Each pause_receive_rx[(FCQN-1):0] bit indicates the corresponding queue is being paused.

This is a level-based signal.
Level Two Title