Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 High-Speed LVDS I/O Overview 2. Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide
1. Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Stratix® 10 LVDS SERDES Usage Modes 1.2. Stratix® 10 LVDS Channels Support 1.3. Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Stratix® 10 Devices 2.5. Differential Receiver in Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Stratix® 10 Devices x
2.5.1. Receiver Blocks in Stratix® 10 Devices 2.5.2. Receiver Modes in Stratix® 10 Devices
2.5.1. Receiver Blocks in Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Signal Interface with LVDS SERDES IP 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP and LVDS SERDES IP in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Initialization and Reset 4.3. LVDS SERDES Intel® FPGA IP Timing 4.4. LVDS SERDES Intel® FPGA IP Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES Intel® FPGA IP Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment Aligning with Control Characters Aligning without Control Characters
4.2.4. Word Boundaries Alignment x
Aligning with Control Characters Aligning without Control Characters 4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES Intel® FPGA IP Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES Intel® FPGA IP Design Examples x
4.4.1. LVDS SERDES IP Synthesizable Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Simulation Design Example 4.4.3. Combined LVDS SERDES IP Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings 5.2. LVDS SERDES Intel® FPGA IP Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings x
5.1.1. LVDS SERDES Intel® FPGA IP General Settings 5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings 5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings 5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Stratix® 10 High-Speed LVDS I/O Overview
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide

4.2.4. Word Boundaries Alignment

You can perform word boundaries alignment with or without control characters in your data stream. If there are no training patterns or control characters available in the serial bit stream to use for word alignment, Intel recommends that you use the non-DPA mode.

Aligning with Control Characters

By adding control characters in the data stream, your logic can search for a known pattern to align the word boundaries. You can compare the received data for each channel, and then pulse the rx_bitslip_ctrl signal as required until you receive the control character.

Note: Intel recommends that you set the bit slip rollover count to the deserialization factor or higher. This setting allows enough depth in the bit slip circuit to roll through an entire word, if required.

Aligning without Control Characters

Without control characters in the data stream, you need a deterministic relationship between the reference clock and the data. With the deterministic relationship, you can predict the word boundary using timing simulation or laboratory measurement. You can only use deterministic relationship in non-DPA mode.

The only way to ensure a deterministic relationship on the default word position in the SERDES when the device powers up, or anytime the PLL is reset, is to have a reference clock equal to the data rate divided by the deserialization factor. This is important because the PLL locks to the rising edge of the reference clock. If you have one rising edge on the reference clock per serial word received, the deserializer always starts at the same position.

For example, if the data rate is 800 Mbps and the deserialization factor is 8, the PLL requires a 100 MHz reference clock.

Using timing simulation, or lab measurements, monitor the parallel words received and determine how many pulses of the rx_bitslip_ctrl you require to set your word boundaries. You can create a simple state machine to apply the required number of pulses after you enter user mode or at any time after you reset the PLL.

Note: If you are using the DPA or soft-CDR modes, the word boundary is not deterministic. The initial training of the DPA allows it to move forward or backward in phase relative to the incoming serial data. Therefore, there can be a ±1 bit of variance in the serial bit where the DPA locks initially.

Section Content
Aligning Word Boundaries

Related Information
Level Two Title