Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 High-Speed LVDS I/O Overview 2. Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide
1. Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Stratix® 10 LVDS SERDES Usage Modes 1.2. Stratix® 10 LVDS Channels Support 1.3. Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Stratix® 10 Devices 2.5. Differential Receiver in Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Stratix® 10 Devices x
2.5.1. Receiver Blocks in Stratix® 10 Devices 2.5.2. Receiver Modes in Stratix® 10 Devices
2.5.1. Receiver Blocks in Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Signal Interface with LVDS SERDES IP 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP and LVDS SERDES IP in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Initialization and Reset 4.3. LVDS SERDES Intel® FPGA IP Timing 4.4. LVDS SERDES Intel® FPGA IP Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES Intel® FPGA IP Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment
4.2.4. Word Boundaries Alignment x
4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES Intel® FPGA IP Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES Intel® FPGA IP Design Examples x
4.4.1. LVDS SERDES IP Synthesizable Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Simulation Design Example 4.4.3. Combined LVDS SERDES IP Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings 5.2. LVDS SERDES Intel® FPGA IP Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings x
5.1.1. LVDS SERDES Intel® FPGA IP General Settings 5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings 5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings 5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Stratix® 10 High-Speed LVDS I/O Overview
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide

5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings

Table 26.  PLL Settings Tab
Parameter Value Description
Use external PLL
  • On
  • Off

Turn on to use an external PLL:

  • The IP does not instantiate a local PLL.
  • The IP creates a series of clock connections with the "ext" prefix. Connect these ports to an externally generated PLL.
  • For details about how to configure the external PLL, refer to the Clock Resource Summary tab of the parameter editor.

This option allows you to access all of the available clocks from the PLL and use advanced PLL features such as clock switchover, bandwidth presets, dynamic phase stepping, and dynamic reconfiguration.

Note: If you want to place combined LVDS transmitters and receivers in the same I/O bank using two LVDS SERDES IP core instances, you must turn on this option. You can also place combined transmitters and receivers in the same I/O bank by turning on the Duplex Feature option in the General Settings tab. If you turn on Duplex Feature, the Use external PLL option is disabled.
Desired inclock frequency —

Specifies the inclock frequency in MHz.

Actual inclock frequency —

Displays the closest inclock frequency to the desired frequency that can source the interface.

FPGA/PLL speed grade —

Displays the FPGA/PLL speed grade, which determines the operation range of the PLL.
Enable pll_areset port
  • On
  • Off

Turn on to expose the pll_areset port. You can use the pll_areset signal to reset the entire LVDS interface.

This setting is enabled if if you turn on Use external PLL.

Core clock resource type —

Specifies onto which clock network the IP core exports an internally generated coreclock.

Note: The current release of the Quartus® Prime software does not support this feature. Use QSF assignments to manually specify this parameter.
Related Information
Level Two Title