Intel® Stratix® 10 TX Transceiver Signal Integrity Development Kit User Guide

Download PDF
ID 683591
Date 9/27/2019
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Kit
2. Getting Started x
2.1. About the Intel® Quartus® Prime Software 2.2. Development Kit Package 2.3. Installing the Intel® FPGA Download Cable II Driver
3. Development Kit Setup x
3.1. Setting up the Development Kit 3.2. Factory Default Switch and Jumper Settings
4. Development Kit Components x
4.1. Development Kit Overview 4.2. Intel® Stratix® 10 TX FPGA 4.3. MAX® V CPLD 4.4. FPGA Configuration 4.5. Status and Setup Elements 4.6. User Input-Output Components 4.7. Clocks 4.8. Transceiver Channels 4.9. Communication Ports 4.10. Flash Memory 4.11. System Power
4.4. FPGA Configuration x
4.4.1. Configuring the FPGA over Embedded Intel® FPGA Download Cable II 4.4.2. Configuring the FPGA through Flash Memory 4.4.3. Configuring the FPGA over External Intel® FPGA Download Cable
4.7. Clocks x
4.7.1. Transceiver Dedicated Clocks 4.7.2. General-Purpose Clocks 4.7.3. Embedded Intel® FPGA Download Cable II Clock
4.10. Flash Memory x
4.10.1. Parallel NOR Flash Memory 4.10.2. EPCQL Flash Memory
4.11. System Power x
4.11.1. Power Guidelines 4.11.2. Power Supply 4.11.3. Power Management 4.11.4. Power Distribution System 4.11.5. Thermal Limitations and Protection Guidelines
5. Board Test System x
5.1. Preparing the Development Kit 5.2. Running the Board Test System 5.3. Using the Board Test System 5.4. Simple Socket Server
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The System Info Tab 5.3.3. The GPIO Tab 5.3.4. The EPCQ Tab 5.3.5. The FMC+ Tab 5.3.6. The PAM4 Tab 5.3.7. The MXP Tab 5.3.8. The QSFPDD1x2 Tab 5.3.9. The QSFPDD2x1 Tab 5.3.10. Power Monitor 5.3.11. Clock Controller
A. Additional Information x
A.1. Add SmartVID settings in QSF file A.2. Safety and Regulatory Information A.3. Compliance and Conformity Information
A.2. Safety and Regulatory Information x
A.2.1. Safety Warnings A.2.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

5.2. Running the Board Test System

Before you begin

The BTS relies on the Intel® Quartus® Prime software's specific library. Before running the BTS, open the Intel® Quartus® Prime software to automatically set the enviromment variable $QUARTUS_ROOTDIR. The BTS uses this environment variable to locate the Intel® Quartus® Prime library. The version of Intel® Quartus® Prime software set in the $QUARTUS_ROOTDIR environment variable should be newer than version 18.1. For example, the Development Kit Installer version 18.1 requires that the Intel® Quartus® Prime software 18.1 or later version to be installed.

Also, to ensure that the FPGA is configured successfully, you should install the latest Intel® Quartus® Prime software that can support the silicon on the development kit. For this board, Intel recommends you install Intel® Quartus® Prime version 19.1.0 B240.

Please refer to the README.txt file under examples\board_test_system directory.

To run the BTS

  1. Navigate to the <package dir>\examples\board_test_system directory and run the BoardTestSystem.exe application.
  2. A GUI appears, displaying the application tab corresponding to the design running in the FPGA. If the design loaded in the FPGA is not supported by the BTS GUI, you will receive a message prompting you to configure your board with a valid BTS design. Refer to the Configure Menu for information on configuring your board.
Level Two Title