R-Tile Avalon® Streaming Intel® FPGA IP for PCI Express* User Guide

ID 683501
Date 6/26/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

4.4.2. Command and Status Signals

Table 82.  PIPE Direct EMIB Data Channel Command and Status SignalsIn the signal names, X is the lane number and ranges from 0 to 15.
Signal Name Direction Descriptions/Notes Clock Domain
lnX_pipe_direct_rxstandby_i Input Synchronous rxstandby signal pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_powerdown_i[1:0] Input PHY power state control signals pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_rate_i[2:0] Input

Gen1-5 rate change control signals:

000: Gen1

001: Gen2

010: Gen3

011: Gen4

100: Gen5

pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_txdetectrx_i Input Receiver detect control signal pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_rxtermination_i Input Controls the presence of receiver terminations. This is a PIPE signal mainly intended for USB usage. Intel recommends driving this signal high (default).
  • 0 = Terminations removed.
  • 1 = Terminations present.
pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_pclkchangeack_i Input Asserted by the MAC when a PCLK rate change or, if required, width change is complete and stable. pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_tx_transfer_en_o Output This signal indicates when the EMIB is ready in PIPE mode. The soft IP controller must release the per-lane lnX_pipe_direct_pld_pcs_rst_n_i signal out of reset after the per-lane lnX_pipe_direct_tx_transfer_en_o signal is asserted. pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_rxstandbystatus_o Output

Indicates whether the PHY is active or in standby mode.

  • 0 = Active
  • 1 = Standby
pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_pclkratechangeok_o Output

This signal is asserted by the PHY when it is ready for the MAC to change the clock rate.

pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_rxstatus_o Output

Reflects the state of the high-speed receiver. A 1 on this bit indicates Rx is detected.

Note: The only status applicable to the PIPE SerDes architecture mode is "Receiver detected".
pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_phystatus_o Output Indicates the completion of several PHY functions including stable PCLK, after reset deassertion, power management state transitions, rate change and receiver detection. pipe_direct_pld_tx_clk_out_o
lnX_pipe_direct_cdrlockstatus_o Output
This is the Receiver CDR lock indicator.
  • 0 = CDR is not locked and is not at the correct frequency.
  • 1 = CDR is at the correct frequency.

If this signal is deasserted when it is expected to be asserted, it indicates a fault condition and the receiver should be reset.

Async
lnX_pipe_direct_cdrlock2data_o Output
This is the Receiver CDR data lock indicator.
  • 0 = CDR is not locked to the data.
  • 1 = CDR is locked to the data. RX data is valid.
Note: This signal will go low when the Soft IP Controller instructs the R-Tile Avalon Streaming IP to start an evaluation of the far end transmitter TX EQ settings (by setting the RxEqEval bit in the Rx Control 3 register). Once the evaluation is completed, the R-Tile Avalon Streaming IP will provide a Figure of Merit value and drive this signal high. For additional details on the Equalization sequence, refer to section 9.10 of the PIPE Specification 5.1.1.
Async