Quartus® Prime Pro Edition User Guide: Timing Analyzer

Download PDF
ID 683243
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
Answers to Top FAQs 1. Timing Analysis Introduction 2. Using the Quartus® Prime Timing Analyzer A. Quartus® Prime Pro Edition User Guides
1. Timing Analysis Introduction x
1.1. What's New In This Version 1.2. Timing Analysis Basic Concepts 1.3. Timing Analysis Overview Document Revision History
1.2. Timing Analysis Basic Concepts x
1.2.1. Timing Path and Clock Analysis 1.2.2. Clock Setup Analysis 1.2.3. Clock Hold Analysis 1.2.4. Recovery and Removal Analysis 1.2.5. Multicycle Path Analysis 1.2.6. Metastability Analysis 1.2.7. Timing Pessimism 1.2.8. Clock-As-Data Analysis 1.2.9. Multicorner Timing Analysis 1.2.10. Time Borrowing
1.2.1. Timing Path and Clock Analysis x
1.2.1.1. The Timing Netlist 1.2.1.2. Timing Paths 1.2.1.3. Data and Clock Arrival Times 1.2.1.4. Launch and Latch Edges
1.2.5. Multicycle Path Analysis x
1.2.5.1. Multicycle Clock Hold 1.2.5.2. Multicycle Clock Setup
1.2.10. Time Borrowing x
1.2.10.1. Time Borrowing Limitations 1.2.10.2. Time Borrowing with Latches 1.2.10.3. Enabling Time Borrowing Optimization
2. Using the Quartus® Prime Timing Analyzer x
2.1. Using Timing Constraints throughout the Design Flow 2.2. Timing Analysis Flow 2.3. Applying Timing Constraints 2.4. Timing Constraint Descriptions 2.5. Timing Report Descriptions 2.6. Scripting Timing Analysis 2.7. Using the Quartus® Prime Timing Analyzer Document Revision History 2.8. Quartus® Prime Pro Edition User Guide: Timing Analyzer Archive
2.2. Timing Analysis Flow x
2.2.1. Step 1: Specify General Timing Analyzer Settings 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Run the Timing Analyzer 2.2.4. Step 4: Analyze Timing Reports
2.2.2. Step 2: Specify Timing Constraints x
2.2.2.1. Specifying SDC-on-RTL Timing Constraints 2.2.2.2. Specifying Conventional SDC Timing Constraints 2.2.2.3. Specifying Synthesis-Only SDC Timing Constraints
2.2.3. Step 3: Run the Timing Analyzer x
2.2.3.1. Running Post-Synthesis Early Timing Analysis 2.2.3.2. Running Post-Fit Timing Analysis
2.2.3.2. Running Post-Fit Timing Analysis x
2.2.3.2.1. Setting the Operating Conditions for Timing Analysis 2.2.3.2.2. Promoting Critical Warnings to Errors
2.2.4. Step 4: Analyze Timing Reports x
2.2.4.1. Cross-Probing with Design Assistant 2.2.4.2. Launching Design Assistant from Timing Analyzer 2.2.4.3. Locating Timing Paths in Other Tools 2.2.4.4. Correlating Constraints to the Timing Report
2.2.4.1. Cross-Probing with Design Assistant x
2.2.4.1.1. Cross-Probing from Design Assistant to Timing Analyzer
2.3. Applying Timing Constraints x
2.3.1. Recommended Initial Conventional SDC Constraints 2.3.2. Example Circuit and Conventional SDC File 2.3.3. SDC File Precedence 2.3.4. Iteratively Modifying Constraints 2.3.5. Applying Entity-Bound Timing Constraints 2.3.6. Constraining Design Partition Ports 2.3.7. Using Fitter Overconstraints
2.3.1. Recommended Initial Conventional SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.5. Applying Entity-Bound Timing Constraints x
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints 2.3.5.2. Using Entity-Bound SDC Files
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints x
2.3.5.1.1. Targeting Constraints to Module Inputs and Outputs 2.3.5.1.2. Entity Based SDC-on-RTL Constraint Scope 2.3.5.1.3. Automatic Scope Example for SDC-on-RTL 2.3.5.1.4. Manual Scope Example for SDC-on-RTL
2.3.5.2. Using Entity-Bound SDC Files x
2.3.5.2.1. Entity-Bound SDC Constraint Scope 2.3.5.2.2. Automatic Scope Entity-bound Constraint Example 2.3.5.2.3. Manual Scope Entity-bound Constraint Example 2.3.5.2.4. Exporting a Design Partition with Entity-bound Constraints 2.3.5.2.5. Importing a Design Partition with Entity-bound Constraints
2.3.6. Constraining Design Partition Ports x
2.3.6.1. Timing Analysis of Imported Compilation Results
2.4. Timing Constraint Descriptions x
2.4.1. Clock Constraints 2.4.2. I/O Constraints 2.4.3. Delay and Skew Constraints 2.4.4. Timing Exception Constraints 2.4.5. Delay Annotation
2.4.1. Clock Constraints x
2.4.1.1. Creating Base Clocks 2.4.1.2. Creating Virtual Clocks 2.4.1.3. Creating Generated Clocks (create_generated_clock) 2.4.1.4. Deriving PLL Clocks 2.4.1.5. Creating Clock Groups (set_clock_groups) 2.4.1.6. Accounting for Clock Effect Characteristics 2.4.1.7. Constraining CDC Paths
2.4.1.1. Creating Base Clocks x
2.4.1.1.1. Automatic Clock Detection and Constraint Creation
2.4.1.2. Creating Virtual Clocks x
2.4.1.2.1. Specifying I/O Interface Uncertainty 2.4.1.2.2. I/O Interface Clock Uncertainty Example
2.4.1.3. Creating Generated Clocks (create_generated_clock) x
2.4.1.3.1. Clock Divider Example (-divide_by) 2.4.1.3.2. Clock Multiplexer Example
2.4.1.5. Creating Clock Groups (set_clock_groups) x
2.4.1.5.1. Exclusive Clock Groups (-logically_exclusive or -physically_exclusive) 2.4.1.5.2. Asynchronous Clock Groups (-asynchronous) 2.4.1.5.3. set_clock_groups Constraint Tips
2.4.1.6. Accounting for Clock Effect Characteristics x
2.4.1.6.1. Set Clock Latency (set_clock_latency) 2.4.1.6.2. Clock Uncertainty
2.4.2. I/O Constraints x
2.4.2.1. Input Constraints (set_input_delay) 2.4.2.2. Output Constraints (set_output_delay)
2.4.3. Delay and Skew Constraints x
2.4.3.1. Advanced I/O Timing and Board Trace Model Delay 2.4.3.2. Maximum Skew (set_max_skew) 2.4.3.3. Net Delay (set_net_delay)
2.4.4. Timing Exception Constraints x
2.4.4.1. Timing Exception Precedence 2.4.4.2. False Paths (set_false_path) 2.4.4.3. Minimum and Maximum Delays 2.4.4.4. Multicycle Paths 2.4.4.5. Multicycle Exception Examples
2.4.4.4. Multicycle Paths x
2.4.4.4.1. Common Multicycle Applications 2.4.4.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.4.4.4.3. Accounting for a Phase Shift (-phase)
2.4.4.5. Multicycle Exception Examples x
2.4.4.5.1. Default Multicycle Analysis 2.4.4.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.4.4.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.4.4.5.4. Same Frequency Clocks with Destination Clock Offset 2.4.4.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.4.4.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.4.4.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.4.4.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.5. Timing Report Descriptions x
2.5.1. Report Fmax Summary 2.5.2. Report Timing 2.5.3. Report Timing By Source Files 2.5.4. Report Data Delay 2.5.5. Report Net Delay 2.5.6. Report Clocks and Clock Network 2.5.7. Report Clock Transfers 2.5.8. Report Metastability 2.5.9. Report CDC Viewer 2.5.10. Report Asynchronous CDC 2.5.11. Report Logic Depth 2.5.12. Report Neighbor Paths 2.5.13. Report Register Spread 2.5.14. Report Route Net of Interest 2.5.15. Report Retiming Restrictions 2.5.16. Report Register Statistics 2.5.17. Report Pipelining Information 2.5.18. Report Time Borrowing Data 2.5.19. Report Exceptions and Exceptions Reachability 2.5.20. Report Bottlenecks 2.5.21. Check Timing 2.5.22. Report SDC
2.5.13. Report Register Spread x
2.5.13.1. Registers with High Timing Path Endpoint Tension 2.5.13.2. Registers with High Immediate Fan-Out Tension
2.5.20. Report Bottlenecks x
2.5.20.1. Specifying Custom Bottleneck Criteria
2.6. Scripting Timing Analysis x
2.6.1. The quartus_sta Executable 2.6.2. The quartus_staw Executable 2.6.3. Collection Commands
2.6.3. Collection Commands x
2.6.3.1. Wildcard Characters 2.6.3.2. Adding and Removing Collection Items 2.6.3.3. Query of Collections 2.6.3.4. Using the get_pins Command
Answers to Top FAQs
1. Timing Analysis Introduction
2. Using the Quartus® Prime Timing Analyzer
A. Quartus® Prime Pro Edition User Guides

2.2.1. Step 1: Specify General Timing Analyzer Settings

Before running timing analysis, you must open an Quartus® Prime project. You can then consider and specify general settings for timing analysis, as well as other project-wide Compiler settings that impact the timing analysis results.

To specify general Timing Analyzer settings, follow these steps:
  1. To open an existing project, click File > Open Project.
  2. Click Assignments > Settings > Timing Analyzer to open the Timing Analyzer settings.
    Figure 38. Timing Analyzer Page of Settings Dialog Box


  3. In the Timing Analyzer page, specify one or more of the following general Timing Analyzer general settings:
    Table 5.  Timing Analyzer General Settings
    Setting Description
    SDC files to include in the project Specifies the name and processing order of timing constraint files in the project, such as conventional .sdc files and SDC-on-RTL (.rtlsdc) files. For more details, refer to Using Timing Constraints Effectively and Step 2: Specify Timing Constraints.
    Interactive Timing Analysis Specify options for automatically running timing analysis, reading constraints, and generating reports automatically. Turn on or off:
    • Automatically launch Timing Analyzer GUI after a full compilation (default, on)
    • Automatically read constraints and update the timing netlist when project is opened in Timing Analyzer (default, on)
    • Automatically run setup summary report when project is opened in Timing Analyzer (default, on)
    Default Reporting Specify options to automatically Report worst-case paths during compilation (default, on). Specify the Paths reported per clock domain (default, 10), and whether to Show routing (default, off) in reports.
    Tcl Script Options Tcl Script File name specifies the file name for a custom timing analysis script. You can specify whether to Run default timing analysis before running custom script.
    Metastability Analysis Specifies how the Timing Analyzer identifies registers as being part of a synchronization register chain for metastability analysis.
  4. Consider and specify project-wide Compiler settings that impact timing analysis:
    Table 6.  Compiler Settings Impacting Timing Analysis
    Setting Description Location
    Enable multicorner support for Timing Analyzer and EDA Netlist Writer(default, on) Directs the Timing Analyzer to perform multicorner timing analysis by default, which analyzes the design against best-case and worst-case operating conditions. Assignments > Settings > Compilation Process Settings
    Optimization Mode (default, Balanced) Specifies the focus of Compiler optimization efforts during synthesis and fitting. Specify a Balanced strategy, or optimize for Performance, Area, Power, Routability, or Compile Time. Assignments > Settings > Compiler Settings
    SDC Constraint Protection (default, off)

    Verifies.sdc constraints in register merging. This option helps to maintain the validity of .sdc constraints through compilation.

    		Assignments > Settings > Compiler Settings > Advanced Settings (Synthesis)
    Synchronization Register Chain Length (default, 3)

    Specifies the maximum number of registers in a row that the Compiler considers as a synchronization chain. The Compiler considers these registers for metastability analysis. The Compiler prevents optimizations of these registers, such as retiming. When gate-level retiming is enabled, the Compiler does not remove these registers.

    		Assignments > Settings > Compiler Settings > Advanced Settings (Synthesis)
    Optimize Design for Metastability (default, on)

    This setting improves the reliability of the design by increasing its Mean Time Between Failures (MTBF). The Fitter increases the output setup slacks of synchronizer registers in the design. This slack can exponentially increase the design MTBF. This option only applies when using the Timing Analyzer for timing-driven compilation. Use the Timing Analyzer report_metastability command to review the synchronizers detected in your design and to produce MTBF estimates.

    		Assignments > Settings > Compiler Settings > Advanced Settings (Fitter)
Level Two Title