Quartus® Prime Pro Edition User Guide: Timing Analyzer

Download PDF
ID 683243
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
Answers to Top FAQs 1. Timing Analysis Introduction 2. Using the Quartus® Prime Timing Analyzer A. Quartus® Prime Pro Edition User Guides
1. Timing Analysis Introduction x
1.1. What's New In This Version 1.2. Timing Analysis Basic Concepts 1.3. Timing Analysis Overview Document Revision History
1.2. Timing Analysis Basic Concepts x
1.2.1. Timing Path and Clock Analysis 1.2.2. Clock Setup Analysis 1.2.3. Clock Hold Analysis 1.2.4. Recovery and Removal Analysis 1.2.5. Multicycle Path Analysis 1.2.6. Metastability Analysis 1.2.7. Timing Pessimism 1.2.8. Clock-As-Data Analysis 1.2.9. Multicorner Timing Analysis 1.2.10. Time Borrowing
1.2.1. Timing Path and Clock Analysis x
1.2.1.1. The Timing Netlist 1.2.1.2. Timing Paths 1.2.1.3. Data and Clock Arrival Times 1.2.1.4. Launch and Latch Edges
1.2.5. Multicycle Path Analysis x
1.2.5.1. Multicycle Clock Hold 1.2.5.2. Multicycle Clock Setup
1.2.10. Time Borrowing x
1.2.10.1. Time Borrowing Limitations 1.2.10.2. Time Borrowing with Latches 1.2.10.3. Enabling Time Borrowing Optimization
2. Using the Quartus® Prime Timing Analyzer x
2.1. Using Timing Constraints throughout the Design Flow 2.2. Timing Analysis Flow 2.3. Applying Timing Constraints 2.4. Timing Constraint Descriptions 2.5. Timing Report Descriptions 2.6. Scripting Timing Analysis 2.7. Using the Quartus® Prime Timing Analyzer Document Revision History 2.8. Quartus® Prime Pro Edition User Guide: Timing Analyzer Archive
2.2. Timing Analysis Flow x
2.2.1. Step 1: Specify General Timing Analyzer Settings 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Run the Timing Analyzer 2.2.4. Step 4: Analyze Timing Reports
2.2.2. Step 2: Specify Timing Constraints x
2.2.2.1. Specifying SDC-on-RTL Timing Constraints 2.2.2.2. Specifying Conventional SDC Timing Constraints 2.2.2.3. Specifying Synthesis-Only SDC Timing Constraints
2.2.3. Step 3: Run the Timing Analyzer x
2.2.3.1. Running Post-Synthesis Early Timing Analysis 2.2.3.2. Running Post-Fit Timing Analysis
2.2.3.2. Running Post-Fit Timing Analysis x
2.2.3.2.1. Setting the Operating Conditions for Timing Analysis 2.2.3.2.2. Promoting Critical Warnings to Errors
2.2.4. Step 4: Analyze Timing Reports x
2.2.4.1. Cross-Probing with Design Assistant 2.2.4.2. Launching Design Assistant from Timing Analyzer 2.2.4.3. Locating Timing Paths in Other Tools 2.2.4.4. Correlating Constraints to the Timing Report
2.2.4.1. Cross-Probing with Design Assistant x
2.2.4.1.1. Cross-Probing from Design Assistant to Timing Analyzer
2.3. Applying Timing Constraints x
2.3.1. Recommended Initial Conventional SDC Constraints 2.3.2. Example Circuit and Conventional SDC File 2.3.3. SDC File Precedence 2.3.4. Iteratively Modifying Constraints 2.3.5. Applying Entity-Bound Timing Constraints 2.3.6. Constraining Design Partition Ports 2.3.7. Using Fitter Overconstraints
2.3.1. Recommended Initial Conventional SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.5. Applying Entity-Bound Timing Constraints x
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints 2.3.5.2. Using Entity-Bound SDC Files
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints x
2.3.5.1.1. Targeting Constraints to Module Inputs and Outputs 2.3.5.1.2. Entity Based SDC-on-RTL Constraint Scope 2.3.5.1.3. Automatic Scope Example for SDC-on-RTL 2.3.5.1.4. Manual Scope Example for SDC-on-RTL
2.3.5.2. Using Entity-Bound SDC Files x
2.3.5.2.1. Entity-Bound SDC Constraint Scope 2.3.5.2.2. Automatic Scope Entity-bound Constraint Example 2.3.5.2.3. Manual Scope Entity-bound Constraint Example 2.3.5.2.4. Exporting a Design Partition with Entity-bound Constraints 2.3.5.2.5. Importing a Design Partition with Entity-bound Constraints
2.3.6. Constraining Design Partition Ports x
2.3.6.1. Timing Analysis of Imported Compilation Results
2.4. Timing Constraint Descriptions x
2.4.1. Clock Constraints 2.4.2. I/O Constraints 2.4.3. Delay and Skew Constraints 2.4.4. Timing Exception Constraints 2.4.5. Delay Annotation
2.4.1. Clock Constraints x
2.4.1.1. Creating Base Clocks 2.4.1.2. Creating Virtual Clocks 2.4.1.3. Creating Generated Clocks (create_generated_clock) 2.4.1.4. Deriving PLL Clocks 2.4.1.5. Creating Clock Groups (set_clock_groups) 2.4.1.6. Accounting for Clock Effect Characteristics 2.4.1.7. Constraining CDC Paths
2.4.1.1. Creating Base Clocks x
2.4.1.1.1. Automatic Clock Detection and Constraint Creation
2.4.1.2. Creating Virtual Clocks x
2.4.1.2.1. Specifying I/O Interface Uncertainty 2.4.1.2.2. I/O Interface Clock Uncertainty Example
2.4.1.3. Creating Generated Clocks (create_generated_clock) x
2.4.1.3.1. Clock Divider Example (-divide_by) 2.4.1.3.2. Clock Multiplexer Example
2.4.1.5. Creating Clock Groups (set_clock_groups) x
2.4.1.5.1. Exclusive Clock Groups (-logically_exclusive or -physically_exclusive) 2.4.1.5.2. Asynchronous Clock Groups (-asynchronous) 2.4.1.5.3. set_clock_groups Constraint Tips
2.4.1.6. Accounting for Clock Effect Characteristics x
2.4.1.6.1. Set Clock Latency (set_clock_latency) 2.4.1.6.2. Clock Uncertainty
2.4.2. I/O Constraints x
2.4.2.1. Input Constraints (set_input_delay) 2.4.2.2. Output Constraints (set_output_delay)
2.4.3. Delay and Skew Constraints x
2.4.3.1. Advanced I/O Timing and Board Trace Model Delay 2.4.3.2. Maximum Skew (set_max_skew) 2.4.3.3. Net Delay (set_net_delay)
2.4.4. Timing Exception Constraints x
2.4.4.1. Timing Exception Precedence 2.4.4.2. False Paths (set_false_path) 2.4.4.3. Minimum and Maximum Delays 2.4.4.4. Multicycle Paths 2.4.4.5. Multicycle Exception Examples
2.4.4.4. Multicycle Paths x
2.4.4.4.1. Common Multicycle Applications 2.4.4.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.4.4.4.3. Accounting for a Phase Shift (-phase)
2.4.4.5. Multicycle Exception Examples x
2.4.4.5.1. Default Multicycle Analysis 2.4.4.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.4.4.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.4.4.5.4. Same Frequency Clocks with Destination Clock Offset 2.4.4.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.4.4.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.4.4.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.4.4.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.5. Timing Report Descriptions x
2.5.1. Report Fmax Summary 2.5.2. Report Timing 2.5.3. Report Timing By Source Files 2.5.4. Report Data Delay 2.5.5. Report Net Delay 2.5.6. Report Clocks and Clock Network 2.5.7. Report Clock Transfers 2.5.8. Report Metastability 2.5.9. Report CDC Viewer 2.5.10. Report Asynchronous CDC 2.5.11. Report Logic Depth 2.5.12. Report Neighbor Paths 2.5.13. Report Register Spread 2.5.14. Report Route Net of Interest 2.5.15. Report Retiming Restrictions 2.5.16. Report Register Statistics 2.5.17. Report Pipelining Information 2.5.18. Report Time Borrowing Data 2.5.19. Report Exceptions and Exceptions Reachability 2.5.20. Report Bottlenecks 2.5.21. Check Timing 2.5.22. Report SDC
2.5.13. Report Register Spread x
2.5.13.1. Registers with High Timing Path Endpoint Tension 2.5.13.2. Registers with High Immediate Fan-Out Tension
2.5.20. Report Bottlenecks x
2.5.20.1. Specifying Custom Bottleneck Criteria
2.6. Scripting Timing Analysis x
2.6.1. The quartus_sta Executable 2.6.2. The quartus_staw Executable 2.6.3. Collection Commands
2.6.3. Collection Commands x
2.6.3.1. Wildcard Characters 2.6.3.2. Adding and Removing Collection Items 2.6.3.3. Query of Collections 2.6.3.4. Using the get_pins Command
Answers to Top FAQs
1. Timing Analysis Introduction
2. Using the Quartus® Prime Timing Analyzer
A. Quartus® Prime Pro Edition User Guides

1.2.8. Clock-As-Data Analysis

The majority of FPGA designs contain simple connections between any two nodes, known as either a data path or a clock path.

A data path is a connection between the output of a synchronous element to the input of another synchronous element.

A clock is a connection to the clock pin of a synchronous element. However, for more complex FPGA designs, such as designs that use source-synchronous interfaces, this simplified view is no longer sufficient. The Timing Analyzer performs clock-as-data analysis in circuits with elements such as clock dividers and DDR source-synchronous outputs.

You can treat the connection between the input clock port and output clock port as a clock path or a data path. Simplified Source Synchronous Output shows a design where the path from port clk_in to port clk_out is both a clock and a data path. The clock path is from the port clk_in to the register reg_data clock pin. The data path is from port clk_in to the port clk_out.

Figure 32. Simplified Source Synchronous Output

With clock-as-data analysis, the Timing Analyzer provides a more accurate analysis of the path based on user constraints. In the clock path analysis, the Timing Analyzer includes any phase shift associated with the phase-locked loop (PLL). For the data path analysis, the Timing Analyzer includes any phase shift associated with the PLL, rather than ignoring the phase shift.

The clock-as-data analysis also applies to internally generated clock dividers. In the following figure, the waveforms are for the inverter feedback path, analyzed during timing analysis. The output of the divider register determines the launch time, and the clock port of the register determines the latch time.

Figure 33. Clock Divider
Level Two Title