Hard Processor System Booting User Guide: Agilex™ 5 SoCs

Download PDF
ID 813762
Date 8/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. FPGA Configuration First Mode 3. HPS Boot First Mode 4. Creating the Configuration Files 5. HPS Boot Flows 6. Configuring the FPGA Fabric from HPS Software 7. Debugging the Agilex™ 5 SoC FPGA Boot Flow 8. Document Revision History for the Hard Processor System Booting User Guide: Agilex™ 5 SoCs
1. Introduction x
1.1. Glossary 1.2. Agilex™ 5 SoC FPGA Boot Overview
2. FPGA Configuration First Mode x
2.1. Boot Flow Overview for FPGA Configuration First Mode 2.2. System Layout for FPGA Configuration First Mode
2.1. Boot Flow Overview for FPGA Configuration First Mode x
2.1.1. Power-On Reset (POR) 2.1.2. Secure Device Manager 2.1.3. First-Stage Bootloader 2.1.4. Second-Stage Bootloader 2.1.5. Operating System 2.1.6. Application
2.2. System Layout for FPGA Configuration First Mode x
2.2.1. External Configuration Host Only 2.2.2. External Configuration Host with HPS Flash 2.2.3. Single SDM Flash 2.2.4. FPGA Configuration First - Dual Flash System
3. HPS Boot First Mode x
3.1. Boot Flow Overview 3.2. System Layout for HPS Boot First Mode
3.1. Boot Flow Overview x
3.1.1. Power-On Reset (POR) 3.1.2. Secure Device Manager 3.1.3. First-Stage Bootloader 3.1.4. Second-Stage Bootloader 3.1.5. Operating System 3.1.6. Application
3.2. System Layout for HPS Boot First Mode x
3.2.1. External Configuration Host Only 3.2.2. External Configuration Host with HPS Flash 3.2.3. Single SDM Flash 3.2.4. HPS Boot First - Dual Flash System
4. Creating the Configuration Files x
4.1. Overview 4.2. Quartus® Prime Hardware Project Compilation 4.3. Bootloader Software Compilation 4.4. Programming File Generator 4.5. Configuration over JTAG 4.6. Configuration from QSPI 4.7. Configuration over AVST 4.8. Configuration via Protocol 4.9. Remote System Update 4.10. Partial Reconfiguration
4.2. Quartus® Prime Hardware Project Compilation x
4.2.1. Device and Pin Options 4.2.2. Platform Designer Options 4.2.3. Generation of Debug HPS FSBL from Hardware Design Build
4.5. Configuration over JTAG x
4.5.1. FPGA Configuration First 4.5.2. HPS Boots First
4.6. Configuration from QSPI x
4.6.1. Supported QSPI Devices 4.6.2. FPGA Configuration First 4.6.3. HPS Boot First
4.6.2. FPGA Configuration First x
4.6.2.1. Creating Configuration Files from Command Line 4.6.2.2. Creating Configuration Files Using Graphical Interface
4.6.3. HPS Boot First x
4.6.3.1. Creating Configuration Files from Command Line 4.6.3.2. Creating Configuration Files Using Graphical Interface
4.7. Configuration over AVST x
4.7.1. FPGA Configuration First 4.7.2. HPS Boot First
4.7.1. FPGA Configuration First x
4.7.1.1. Creating Configuration Files from Command Line 4.7.1.2. Creating Configuration Files Using Graphical Interface
4.7.2. HPS Boot First x
4.7.2.1. Creating Configuration Files from Command Line 4.7.2.2. Creating Configuration Files Using Graphical Interface
4.8. Configuration via Protocol x
4.8.1. Creating Configuration Files from Command Line 4.8.2. Creating Configuration Files Using Graphical Interface
5. HPS Boot Flows x
5.1. U-Boot ATF Linux* Boot 5.2. ATF Linux Boot 5.3. ATF Zephyr* Boot
6. Configuring the FPGA Fabric from HPS Software x
6.1. Configuring the FPGA Fabric from U-Boot 6.2. Configuring the FPGA Fabric from Linux* 6.3. FPGA Partial Reconfiguration from Linux*
7. Debugging the Agilex™ 5 SoC FPGA Boot Flow x
7.1. Reset 7.2. Debugging the HPS Bootloader Using the Arm* Development Studio for Intel® SoC FPGA (Arm* DS for Intel® SoC FPGA) Edition
7.1. Reset x
7.1.1. HPS Reset Pin 7.1.2. L4 Watchdog Timer 0
1. Introduction
2. FPGA Configuration First Mode
3. HPS Boot First Mode
4. Creating the Configuration Files
5. HPS Boot Flows
6. Configuring the FPGA Fabric from HPS Software
7. Debugging the Agilex™ 5 SoC FPGA Boot Flow
8. Document Revision History for the Hard Processor System Booting User Guide: Agilex™ 5 SoCs

4.7.2. HPS Boot First

In this case, the device gets first configured with a small phase 1 bitstream from QSPI flash, the HPS IO, HPS DDR are configured and HPS starts running the FSBL. Then at a later time the HPS software can configure the FPGA fabric using the typically much larger phase 2 configuration bitstream. The following figure shows an overview of the process:

Figure 25. Configuration over Avalon® streaming interface Using HPS Boot First
  1. Compile hardware project with Quartus® Prime to obtain the SOF file.
  2. Compile the HPS FSBL source code to obtain the HPS FSBL hex file, or use a precompiled one.
  3. Use Programming File Generator to create the following files:
    • Raw Binary File (RBF): contains the small phase 1 configuration bitstream.
    • Core RBF File: contains the typically much larger phase 2 configuration bitstream, to be used by HPS software later to configure the fabric.
  4. Set MSEL to the AVST mode.
  5. Power up, power cycle or toggle nCONFIG on the device.
  6. Use an external initiator connected over AVST to configure the device using the phase 1 bitstream. HPS software starts running, beginning with HPS FSBL. The HPS software configures the FPGA fabric by using the phase 2 Core RBF bitstream at a later time.

Section Content
Creating Configuration Files from Command Line
Creating Configuration Files Using Graphical Interface

Level Two Title