Hard Processor System Booting User Guide: Agilex™ 5 SoCs

Download PDF
ID 813762
Date 12/20/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. FPGA Configuration First Mode 3. HPS Boot First Mode 4. Creating the Configuration Files 5. HPS Boot Flows 6. Configuring the FPGA Fabric from HPS Software 7. Debugging the Agilex™ 5 SoC FPGA Boot Flow 8. Document Revision History for the Hard Processor System Booting User Guide: Agilex™ 5 SoCs
1. Introduction x
1.1. Glossary 1.2. Agilex™ 5 SoC FPGA Boot Overview
2. FPGA Configuration First Mode x
2.1. Boot Flow Overview for FPGA Configuration First Mode 2.2. System Layout for FPGA Configuration First Mode
2.1. Boot Flow Overview for FPGA Configuration First Mode x
2.1.1. Power-On Reset (POR) 2.1.2. Secure Device Manager 2.1.3. First-Stage Bootloader 2.1.4. Second-Stage Bootloader 2.1.5. Operating System 2.1.6. Application
2.2. System Layout for FPGA Configuration First Mode x
2.2.1. External Configuration Host Only 2.2.2. External Configuration Host with HPS Flash 2.2.3. Single SDM Flash 2.2.4. FPGA Configuration First - Dual Flash System
3. HPS Boot First Mode x
3.1. Boot Flow Overview 3.2. System Layout for HPS Boot First Mode
3.1. Boot Flow Overview x
3.1.1. Power-On Reset (POR) 3.1.2. Secure Device Manager 3.1.3. First-Stage Bootloader 3.1.4. Second-Stage Bootloader 3.1.5. Operating System 3.1.6. Application
3.2. System Layout for HPS Boot First Mode x
3.2.1. External Configuration Host Only 3.2.2. External Configuration Host with HPS Flash 3.2.3. Single SDM Flash 3.2.4. HPS Boot First - Dual Flash System
4. Creating the Configuration Files x
4.1. Overview 4.2. Quartus® Prime Hardware Project Compilation 4.3. Bootloader Software Compilation 4.4. Programming File Generator 4.5. Configuration over JTAG 4.6. Configuration from QSPI 4.7. Configuration over AVST 4.8. Configuration via Protocol 4.9. Remote System Update 4.10. Partial Reconfiguration 4.11. Preserving SDRAM Content across HPS Resets for Agilex™ 5 Devices
4.2. Quartus® Prime Hardware Project Compilation x
4.2.1. Device and Pin Options 4.2.2. Platform Designer Options 4.2.3. Generation of Debug HPS FSBL from Hardware Design Build
4.5. Configuration over JTAG x
4.5.1. FPGA Configuration First 4.5.2. HPS Boots First
4.6. Configuration from QSPI x
4.6.1. Supported QSPI Devices 4.6.2. FPGA Configuration First 4.6.3. HPS Boot First
4.6.2. FPGA Configuration First x
4.6.2.1. Creating Configuration Files from Command Line 4.6.2.2. Creating Configuration Files Using Graphical Interface
4.6.3. HPS Boot First x
4.6.3.1. Creating Configuration Files from Command Line 4.6.3.2. Creating Configuration Files Using Graphical Interface
4.7. Configuration over AVST x
4.7.1. FPGA Configuration First 4.7.2. HPS Boot First
4.7.1. FPGA Configuration First x
4.7.1.1. Creating Configuration Files from Command Line 4.7.1.2. Creating Configuration Files Using Graphical Interface
4.7.2. HPS Boot First x
4.7.2.1. Creating Configuration Files from Command Line 4.7.2.2. Creating Configuration Files Using Graphical Interface
4.8. Configuration via Protocol x
4.8.1. Creating Configuration Files from Command Line 4.8.2. Creating Configuration Files Using Graphical Interface
4.11. Preserving SDRAM Content across HPS Resets for Agilex™ 5 Devices x
4.11.1. Data Retention Mechanism Flow 4.11.2. Setting to Enable the Data Retention Mechanism 4.11.3. Preserving Data in SDRAM Across Reset Examples
5. HPS Boot Flows x
5.1. U-Boot ATF Linux* Boot 5.2. ATF Linux Boot 5.3. ATF Zephyr* Boot
6. Configuring the FPGA Fabric from HPS Software x
6.1. Configuring the FPGA Fabric from U-Boot 6.2. Configuring the FPGA Fabric from Linux* 6.3. FPGA Partial Reconfiguration from Linux* 6.4. Hardware Project Compatibility in HPS Boot First Mode
6.4. Hardware Project Compatibility in HPS Boot First Mode x
6.4.1. HPS IO Hash Compatibility 6.4.2. HPS IO Hash Handling as related to the HPS EMIF IO Bank(s)
6.4.2. HPS IO Hash Handling as related to the HPS EMIF IO Bank(s) x
6.4.2.1. IO Configuration Differences on non-HPS EMIF IPs 6.4.2.2. Pin Location Differences 6.4.2.3. PLL Differences 6.4.2.4. Clock Spine Differences 6.4.2.5. HPS IO Hash Mismatch Troubleshooting Examples for HPS EMIF IOs
6.4.2.4. Clock Spine Differences x
6.4.2.4.1. Agilex™ 5-Specific Clock Spine Differences 6.4.2.4.2. Register Packing Differences
7. Debugging the Agilex™ 5 SoC FPGA Boot Flow x
7.1. Reset 7.2. Debugging the HPS Bootloader Using the Arm* Development Studio for Intel® SoC FPGA (Arm* DS for Intel® SoC FPGA) Edition
7.1. Reset x
7.1.1. HPS Reset Pin 7.1.2. L4 Watchdog Timer 0
1. Introduction
2. FPGA Configuration First Mode
3. HPS Boot First Mode
4. Creating the Configuration Files
5. HPS Boot Flows
6. Configuring the FPGA Fabric from HPS Software
7. Debugging the Agilex™ 5 SoC FPGA Boot Flow
8. Document Revision History for the Hard Processor System Booting User Guide: Agilex™ 5 SoCs

4.7.1.2. Creating Configuration Files Using Graphical Interface

The following example creates the AVST configuration files for FPGA first mode using the Programming File Generator in GUI mode:

  1. Start the Programming File Generator in GUI mode by running the qpfgw command.
  2. Select the Device Family to be Agilex™ 5.
  3. Select the Configuration mode to be AVST x8.
  4. In the Output Files tab:
    1. Change the output file Name to “design”.
    2. Check Raw Binary File (.rbf) option – the others are grayed out.
    The Quartus® Prime Programming File Generator window is displayed:
    Figure 23.  Quartus® Prime Programming File Generator Pro Edition Window: Output Files
  5. Switch to Input Files tab by clicking it. In the Input Files tab, do the following:
    1. Click the Add Bitstream button, browse to your SOF file, then click Open.
    2. Click the newly added design.sof file, then click Properties. In the HPS settings > Bootloader section, click the “..” browse button, go to the location of your HPS FSBL hex file, select it and click Open.
      The Quartus® Prime Programming File Generator window is displayed:
      Figure 24.  Quartus® Prime Programming File Generator Pro Edition Window: Input Files
  6. Click the Generate button. Once the files are generated, a confirmation message is received.
  7. Optionally, go to File > Save or File > Save As to save the configuration in a .pfg file. You can generate the output again by applying the same options by running the command line version of the tool like this: 
    quartus_pfg -c <filename.pfg>
Level Two Title