Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide

Download PDF
ID 782461
Date 12/04/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Quartus® Prime Software and Driver Installation
2.3. Quartus® Prime Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Pro Edition Software 2.3.2. Installing the Intel® SoC EDS 2.3.3. Installing the Development Kit 2.3.4. Installing the Intel® FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash with Default Factory Image
4. Board Test System x
4.1. Set Up the BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control the On-board Clock through Clock Controller GUI 4.4. Monitor On-Board Power Regulator through Power Monitor GUI 4.5. Identify Test Pass or Fail-based on BTS GUI Test Status
4.1. Set Up the BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Setting Up the Quartus® Prime Software for BTS Operation 4.1.5. Running the BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Information Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. Transceiver Designs
4.2.5. Transceiver Designs x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The QSFPDD PAM4 Tab 4.2.5.3. The FMC+ NRZ Tab 4.2.5.4. The QSFPDD800 PAM4 Tab
4.3. Control the On-board Clock through Clock Controller GUI x
4.3.1. Si5391-1 4.3.2. Si5391-2 4.3.3. Si5392 4.3.4. Si5395 4.3.5. Si5332 4.3.6. Si5518
5. Development Kit Hardware and Configuration x
5.1. Configuring FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring FPGA Device Using the Avalon® Streaming Interface x8 Configuration Mode 5.3. Daughter Card
5.3. Daughter Card x
5.3.1. HPS Out of Box Experience (OOBE) Daughter Card
6. Custom Projects for the Development Kit x
6.1. Add SmartVID Settings in the Quartus® Prime QSF File 6.2. Golden Top
A. Development Kit Components x
A.1. Power A.2. Clocks A.3. General Input/Output A.4. Memory Interfaces A.5. Communication Interfaces A.6. Daughter Card A.7. Connectors and Cables
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings Power Supply Hazardous Voltage Power Connect and Disconnect System Grounding (Earthing) Power Cord Requirements Lightning/Electrical Storm Risk of Fire C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

C.1.1. Safety Warnings

Power Supply Hazardous Voltage

AC mains voltages are present within the power supply assembly. No user serviceable parts are present inside the power supply.

Power Connect and Disconnect

The AC power supply cord is the primary disconnect device from mains (AC power) and used to remove all DC power from the board/system. The socket outlet must be installed near the equipment and must be readily accessible.

System Grounding (Earthing)

To avoid shock, you must ensure that the power cord is connected to a properly wired and grounded receptacle. Ensure that any equipment to which this product is attached to is also connected to properly wired and grounded receptacles.

Power Cord Requirements

The plug on the power cord must be a grounding-type male plug designed for use in your region. It must have certification marks showing certification by an agency in your region. The connector that plugs into the appliance inlet of the power supply must be an IEC 320, sheet C13, female connector. If the power cord supplied with the system does not meet requirements for use in your region, discard the cord, and do not use it with adapters. Use only certified power supply cord with appropriate gauge, designed for use in your region.

Lightning/Electrical Storm

Do not connect/disconnect any cables or perform installation/maintenance of this product during an electrical storm.

Risk of Fire

To reduce the risk of fire, keep all flammable materials a safe distance away from the boards and power supply. You must configure the development kit on a flame retardant surface.

Level Two Title