Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide

Download PDF
ID 782461
Date 12/04/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Quartus® Prime Software and Driver Installation
2.3. Quartus® Prime Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Pro Edition Software 2.3.2. Installing the Intel® SoC EDS 2.3.3. Installing the Development Kit 2.3.4. Installing the Intel® FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash with Default Factory Image
4. Board Test System x
4.1. Set Up the BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control the On-board Clock through Clock Controller GUI 4.4. Monitor On-Board Power Regulator through Power Monitor GUI 4.5. Identify Test Pass or Fail-based on BTS GUI Test Status
4.1. Set Up the BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Setting Up the Quartus® Prime Software for BTS Operation 4.1.5. Running the BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Information Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. Transceiver Designs
4.2.5. Transceiver Designs x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The QSFPDD PAM4 Tab 4.2.5.3. The FMC+ NRZ Tab 4.2.5.4. The QSFPDD800 PAM4 Tab
4.3. Control the On-board Clock through Clock Controller GUI x
4.3.1. Si5391-1 4.3.2. Si5391-2 4.3.3. Si5392 4.3.4. Si5395 4.3.5. Si5332 4.3.6. Si5518
5. Development Kit Hardware and Configuration x
5.1. Configuring FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring FPGA Device Using the Avalon® Streaming Interface x8 Configuration Mode 5.3. Daughter Card
5.3. Daughter Card x
5.3.1. HPS Out of Box Experience (OOBE) Daughter Card
6. Custom Projects for the Development Kit x
6.1. Add SmartVID Settings in the Quartus® Prime QSF File 6.2. Golden Top
A. Development Kit Components x
A.1. Power A.2. Clocks A.3. General Input/Output A.4. Memory Interfaces A.5. Communication Interfaces A.6. Daughter Card A.7. Connectors and Cables
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

4.3. Control the On-board Clock through Clock Controller GUI

The Clock Controller GUI can control the outputs of on-board Si5391-1/Si5391-2/Si5392/ Si5395/Si5332/Si5518. The instructions to run Clock Controller GUI are stated in the Running the BTS GUI section. Alternatively, you can start using the Clock Controller feature by selecting the Clock icon on the BTS GUI.

The Clock Controller communicates with the system MAX® 10 device through 10-pin JTAG header J7 or USB port J1. Then, the system MAX® 10 controls the programmable clock part through a 2-wire I2C bus.

Note: You cannot run the stand-alone Clock Controller GUI application when the BTS or Power Monitor GUI is running at the same time.
Note: Si5518 can be controlled only when a design in which the SPI interface is instantiated, such as the bts_config.sof under the board_test_system\image\ES folder that has been downloaded to the FPGA.

Section Content
Si5391-1
Si5391-2
Si5392
Si5395
Si5332
Si5518

Related Information
Level Two Title