F-Tile CPRI PHY Multirate Intel® FPGA IP User Guide

Download PDF
ID 710578
Date 12/04/2023
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Configuration Registers 7. F-Tile CPRI PHY Multirate Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile CPRI PHY Multirate Intel® FPGA IP User Guide
1. Introduction x
1.1. IP Core Overview 1.2. Release Information 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Related Documentation
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. TX MII Interface (64b/66b) 2.4. RX MII Interface (64b/66b) 2.5. Status Interface for 64b/66b Line Rate 2.6. TX Interface (8b/10b) 2.7. RX Interface (8b/10b) 2.8. Status Interface for 8b/10b Line Rate 2.9. TX Tunnel Interface 2.10. Using TX Tunnel Interface 2.11. RX Tunnel Interface 2.12. Using RX Tunnel Interface 2.13. Status Interface for Tunnel Line Rate 2.14. Serial Interface 2.15. CPRI PHY Reconfiguration Interface 2.16. Datapath Avalon Memory-Mapped Interface 2.17. PMA Avalon Memory-Mapped Interface
2.1. Clock Signals x
2.1.1. Required Clock Frequencies
3. Parameters x
3.1. Sub Profile Parameters Validation
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Dynamic Reconfiguration Settings
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.2. Specifying the IP Core Parameters and Options x
4.2.1. Reference and System PLL Clock for your IP Design
5. Block Description x
5.1. Latency Measurement 5.2. CDR Clock Output 5.3. RX PMA Adaptation
5.1. Latency Measurement x
5.1.1. Deterministic Latency 5.1.2. Calculation for 64b/66b Datapath
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Configuration Registers
7. F-Tile CPRI PHY Multirate Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile CPRI PHY Multirate Intel® FPGA IP User Guide

4.2.1. Reference and System PLL Clock for your IP Design

Each F-tile system must instantiate one F-Tile Reference and System PLL Clocks Intel FPGA IP. The F-Tile Reference and System PLL Clocks Intel FPGA IP performs three main functions:
  1. Configure reference clock for FHT PMA:
    • Enable the FHT common PLLs and select the reference clock source for FHT common PLL
    • Specify the FHT reference clock source frequency
    Note: The F-Tile CPRI PHY Intel® FPGA IP core does not support FHT PMA. The IP core implementation uses FGT PMA.
  2. Configure reference clock for FGT PMA:
    • Enable FGT reference clocks and specify the reference clock frequency
    • Specify FGT CDR output
  3. Configure system PLL:
    • Enable system PLL and specify its mode
    • Specify the reference clock source and frequency for system PLL
Note: In your IP design, you must include an F-Tile Reference and System PLL Clocks Intel FPGA IP core to pass logic generation flow.

The F-Tile Reference and System PLL Clocks Intel FPGA IP must always connect to a protocol based Intel FPGA IP. The F-Tile Reference and System PLL Clocks Intel FPGA IP cannot be compiled or simulated as a standalone IP. For more information on parameters and port list for F-Tile Reference and System PLL Clocks Intel FPGA IP core, refer to Implementing the F-Tile Reference and System PLL Clocks Intel FPGA IP section of the F-tile Architecture and PMA and FEC Direct PHY IP User Guide.

When you design multiple interfaces or protocol-based IP cores within a single F-tile, you must use only one instance of the F-Tile Reference and System PLL Clocks Intel FPGA IP core to configure:
  • All required reference clocks for FGT PMA (up to 10) and FHT PMA (up to 2) to implement multiple interfaces within a single F-tile.
  • All required FHT common PLLs (up to 2) to implement multiple interfaces within a single F-tile.
  • All required System PLLs (up to 3) to implement multiple interfaces within a single F-tile.
  • All required reference clocks for system PLLs (up to 8 – shared with FGT PMA) to implement multiple interfaces within a single F-tile.

When you design multiple interfaces or protocol-based IP cores within a single F-tile, you can only use three System PLLs. For example, you can use one System PLL for PCIe and two for Ethernet and other protocols. However, there are other use cases where you can use all three for various interfaces within the Ethernet and PMA-Direct digital blocks. As there are only three System PLLs, multiple interfaces or protocol-based IP cores with different line rates may have to share a System PLL. While sharing a System PLL, the interface with the highest line rate determines the system PLL frequency, and the interfaces with the lower line rates must be overclocked. For more information, refer to Implementing the F-Tile Reference and System PLL Clocks Intel FPGA IP section of the F-tile Architecture and PMA and FEC Direct PHY IP User Guide.

Related Information
Level Two Title