F-Tile CPRI PHY Multirate Intel® FPGA IP User Guide

Download PDF
ID 710578
Date 12/04/2023
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Configuration Registers 7. F-Tile CPRI PHY Multirate Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile CPRI PHY Multirate Intel® FPGA IP User Guide
1. Introduction x
1.1. IP Core Overview 1.2. Release Information 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Related Documentation
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. TX MII Interface (64b/66b) 2.4. RX MII Interface (64b/66b) 2.5. Status Interface for 64b/66b Line Rate 2.6. TX Interface (8b/10b) 2.7. RX Interface (8b/10b) 2.8. Status Interface for 8b/10b Line Rate 2.9. TX Tunnel Interface 2.10. Using TX Tunnel Interface 2.11. RX Tunnel Interface 2.12. Using RX Tunnel Interface 2.13. Status Interface for Tunnel Line Rate 2.14. Serial Interface 2.15. CPRI PHY Reconfiguration Interface 2.16. Datapath Avalon Memory-Mapped Interface 2.17. PMA Avalon Memory-Mapped Interface
2.1. Clock Signals x
2.1.1. Required Clock Frequencies
3. Parameters x
3.1. Sub Profile Parameters Validation
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Dynamic Reconfiguration Settings
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.2. Specifying the IP Core Parameters and Options x
4.2.1. Reference and System PLL Clock for your IP Design
5. Block Description x
5.1. Latency Measurement 5.2. CDR Clock Output 5.3. RX PMA Adaptation
5.1. Latency Measurement x
5.1.1. Deterministic Latency 5.1.2. Calculation for 64b/66b Datapath
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Configuration Registers
7. F-Tile CPRI PHY Multirate Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile CPRI PHY Multirate Intel® FPGA IP User Guide

4.1.1. Intel® FPGA IP Evaluation Mode

The free Intel® FPGA IP Evaluation Mode allows you to evaluate licensed Intel® FPGA IP cores in simulation and hardware before purchase. Intel® FPGA IP Evaluation Mode supports the following evaluations without additional license:
  • Simulate the behavior of a licensed Intel® FPGA IP core in your system.
  • Verify the functionality, size, and speed of the IP core quickly and easily.
  • Generate time-limited device programming files for designs that include IP cores.
  • Program a device with your IP core and verify your design in hardware.

Intel® FPGA IP Evaluation Mode supports the following operation modes:

  • Tethered—Allows running the design containing the licensed Intel® FPGA IP indefinitely with a connection between your board and the host computer. Tethered mode requires a serial joint test action group (JTAG) cable connected between the JTAG port on your board and the host computer, which is running the Intel® Quartus® Prime Programmer for the duration of the hardware evaluation period. The Programmer only requires a minimum installation of the Intel® Quartus® Prime software, and requires no Intel® Quartus® Prime license. The host computer controls the evaluation time by sending a periodic signal to the device via the JTAG port. If all licensed IP cores in the design support tethered mode, the evaluation time runs until any IP core evaluation expires. If all of the IP cores support unlimited evaluation time, the device does not time-out.
  • Untethered—Allows running the design containing the licensed IP for a limited time. The IP core reverts to untethered mode if the device disconnects from the host computer running the Intel® Quartus® Prime software. The IP core also reverts to untethered mode if any other licensed IP core in the design does not support tethered mode.

When the evaluation time expires for any licensed Intel® FPGA IP in the design, the design stops functioning. All IP cores that use the Intel® FPGA IP Evaluation Mode time out simultaneously when any IP core in the design times out. When the evaluation time expires, you must reprogram the FPGA device before continuing hardware verification. To extend use of the IP core for production, purchase a full production license for the IP core.

You must purchase the license and generate a full production license key before you can generate an unrestricted device programming file. During Intel® FPGA IP Evaluation Mode, the Compiler only generates a time-limited device programming file (<project name> _time_limited.sof) that expires at the time limit.

Figure 9.  Intel® FPGA IP Evaluation Mode Flow
Note: Refer to each IP core's user guide for parameterization steps and implementation details.

Intel® licenses IP cores on a per-seat, perpetual basis. The license fee includes first-year maintenance and support. You must renew the maintenance contract to receive updates, bug fixes, and technical support beyond the first year. You must purchase a full production license for Intel® FPGA IP cores that require a production license, before generating programming files that you may use for an unlimited time. During Intel® FPGA IP Evaluation Mode, the Compiler only generates a time-limited device programming file (<project name> _time_limited.sof) that expires at the time limit. To obtain your production license keys, visit the Intel® FPGA Self-Service Licensing Center.

The Intel® FPGA Software License Agreements govern the installation and use of licensed IP cores, the Intel® Quartus® Prime design software, and all unlicensed IP cores.

Related Information
Level Two Title