Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 High-Speed LVDS I/O Overview 2. Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide
1. Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Stratix® 10 LVDS SERDES Usage Modes 1.2. Stratix® 10 LVDS Channels Support 1.3. Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Stratix® 10 Devices 2.5. Differential Receiver in Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Stratix® 10 Devices x
2.5.1. Receiver Blocks in Stratix® 10 Devices 2.5.2. Receiver Modes in Stratix® 10 Devices
2.5.1. Receiver Blocks in Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Signal Interface with LVDS SERDES IP 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP and LVDS SERDES IP in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Initialization and Reset 4.3. LVDS SERDES Intel® FPGA IP Timing 4.4. LVDS SERDES Intel® FPGA IP Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES Intel® FPGA IP Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment
4.2.4. Word Boundaries Alignment x
4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES Intel® FPGA IP Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES Intel® FPGA IP Design Examples x
4.4.1. LVDS SERDES IP Synthesizable Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Simulation Design Example 4.4.3. Combined LVDS SERDES IP Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings 5.2. LVDS SERDES Intel® FPGA IP Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings x
5.1.1. LVDS SERDES Intel® FPGA IP General Settings 5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings 5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings 5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Stratix® 10 High-Speed LVDS I/O Overview
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide

5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings

The parameter options in the Transmitter Settings tab are available if you select the TX functional mode in the General Settings tab.
Table 30.  Transmitter Settings Tab
Parameter Value Description
TX core registers clock
  • tx_coreclock
  • inclock

Selects the clock that clocks the core registers:

  • tx_coreclock—selects the tx_coreclock as the clock source.
  • inclock—select the PLL refclk as the clock source. The refclk frequency must be equal to the data rate divided by the serialization factor.

This parameter is available only in the TX functional mode.

Enable tx_coreclock port
  • On
  • Off

Turn on to expose the tx_coreclock port that you can use to drive the core logic feeding the transmitter.

  • If the Use the clock phase alignment block for improved periphery-core timing for even SERDES factors option in the General Settings tab is turned off, the tx_coreclock signal is a feedthrough of the ext_coreclock input.
  • If the Use the clock phase alignment block for improved periphery-core timing for even SERDES factors option in the General Settings tab is turned on, the tx_coreclock signal is a phase-aligned core clock signal generated by the loaden.

Intel recommends that you use the tx_coreclock output signal if it is requested.

Note: This option is disabled if the Use external PLL option in the PLL Settings tab is turned on. To expose the tx_coreclock when using external PLL, turn off Use external PLL option before turning on the Enable tx_coreclock port. After making changes to Enable tx_coreclock port, you can turn Use external PLL back on.
Enable tx_outclock port
  • On
  • Off

Turn on to expose the tx_outclock port.

  • The tx_outclock port frequency depends on the setting for the Tx_outclock division factor parameter.
  • The phases of the tx_outclock_p and tx_outclock_n ports depend on the Desired tx_outclock phase shift parameter.

Turning on this parameter reduces the maximum number of channels per transmitter interface by one channel.
Desired tx_outclock phase shift (degrees)

Refer to related information.

Specifies the phase relationship between the outclock and outgoing serial data in degrees of the LVDS fast clock.

Actual tx_outclock phase shift (degrees)

Depends on fast_clock and tx_outclock frequencies. Refer to related information.

Displays the closest achievable tx_outclock phase shift to the desired tx_outclock phase shift.

Tx_outclock division factor Depends on the SERDES factor. Specifies the ratio of the fast clock frequency to the outclock frequency. For example, the maximum number of serial transitions per outclock cycle.

Section Content
Setting the Transmitter Output Clock Parameters

Related Information
Level Two Title