Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 High-Speed LVDS I/O Overview 2. Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide
1. Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Stratix® 10 LVDS SERDES Usage Modes 1.2. Stratix® 10 LVDS Channels Support 1.3. Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Stratix® 10 Devices 2.5. Differential Receiver in Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Stratix® 10 Devices x
2.5.1. Receiver Blocks in Stratix® 10 Devices 2.5.2. Receiver Modes in Stratix® 10 Devices
2.5.1. Receiver Blocks in Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Signal Interface with LVDS SERDES IP 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP and LVDS SERDES IP in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Initialization and Reset 4.3. LVDS SERDES Intel® FPGA IP Timing 4.4. LVDS SERDES Intel® FPGA IP Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES Intel® FPGA IP Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment
4.2.4. Word Boundaries Alignment x
4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES Intel® FPGA IP Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES Intel® FPGA IP Design Examples x
4.4.1. LVDS SERDES IP Synthesizable Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Simulation Design Example 4.4.3. Combined LVDS SERDES IP Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings 5.2. LVDS SERDES Intel® FPGA IP Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings x
5.1.1. LVDS SERDES Intel® FPGA IP General Settings 5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings 5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings 5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Stratix® 10 High-Speed LVDS I/O Overview
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide

5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings

The parameter options in the Receiver Settings tab are available if you select the RX Non-DPA, RX DPA-FIFO, or RX Soft-CDR functional mode in the General Settings tab.
Table 27.  Receiver Settings Tab—Bitslip Settings
Parameter Value Description
Enable bitslip mode
  • On
  • Off

Turn on to add a bit slip block to the receiver data path and expose the rx_bitslip_ctrl port (one input per channel).

Every assertion of the rx_bitslip_ctrl signal adds one bit of serial latency to the data path of the specified channel.

Enable rx_bitslip_reset port
  • On
  • Off

Turn on to expose the rx_bitslip_reset port (one input per channel) that you can use to reset the bit slip.

Enable rx_bitslip_max port
  • On
  • Off

Turn on to expose the rx_bitslip_max port (one output per channel).

When asserted, the next rising edge of rx_bitslip_ctrl resets the latency of the bit slip to zero.

Bitslip rollover value Deserialization factor

Specifies the maximum latency that the bit slip can inject.

When the bit slip reaches the specified value, it rolls over and the rx_bitslip_max signal asserts.

The rollover value is set automatically to the deserialization factor.
Table 28.  Receiver Settings Tab—DPA Settings
Parameter Value Description
Enable rx_dpa_reset port
  • On
  • Off

Turn on to expose the rx_dpa_reset port that you can use to reset the DPA logic of each channel independently.

(Formerly known as rx_reset.)

Enable rx_fifo_reset port
  • On
  • Off

Turn on to use your logic to drive the rx_fifo_reset port to reset the DPA-FIFO block.

Enable rx_dpa_hold port
  • On
  • Off

Turn on to expose the rx_dpa_hold input port (one input per channel).

If set high, the DPA logic in the corresponding channel does not switch sampling phases.

(Formerly known as rx_dpll_hold.)

Enable DPA loss of lock on one change
  • On
  • Off
  • On—the IP drives the rx_dpa_locked signal low when the DPA changes phase selection from the initially locked position. When the DPA changes the phase selection back to the initial locked position, the IP drives the rx_dpa_locked signal high.
  • Off—the IP drives the rx_dpa_locked signal low when the DPA moves two phases in the same direction away from the initial locked position. When the DPA changes the phase selection to be within one phase or same phase as the initial locked position, the IP drives the rx_dpa_locked signal high.

Deassertion of rx_dpa_locked does not indicate that the data is invalid. Instead, the deassertion indicates that the DPA has changed phase taps to track variations between the inclock and rx_in data.

Intel recommends that you use data checkers to verify data accuracy.

Enable DPA alignment only to rising edges of data
  • On
  • Off
  • On—DPA logic counts only the rising edges of the incoming serial data
  • Off—DPA logic counts the rising and falling edges
Note: Intel recommends that you use this port only for high jitter systems and turn it off for typical applications.
(Simulation only) Specify PPM drift on the recovered clock(s) — Specifies the amount of phase drift the LVDS SERDES IP simulation model adds to the recovered rx_divfwdclks.
Note: The current release of the Quartus® Prime software does not support this feature.
Table 29.  Receiver Settings Tab—Non-DPA Settings
Parameter Value Description
Desired receiver inclock phase shift (degrees) —

Specifies, in degrees of the LVDS fast clock, the ideal phase delay of inclock with respect to transitions in the incoming serial data.

For example, specifying 180° implies that the inclock is center aligned to the incoming data.

Actual receiver inclock phase shift (degrees)

Depends on the fast_clock and inclock frequencies. Refer to the related information.

Specifies the closest achievable receiver inclock phase shift to the desired receiver inclock phase shift.


Section Content
Receiver Input Clock Parameters Setup

Related Information
Level Two Title