Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 High-Speed LVDS I/O Overview 2. Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide
1. Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Stratix® 10 LVDS SERDES Usage Modes 1.2. Stratix® 10 LVDS Channels Support 1.3. Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Stratix® 10 Devices 2.5. Differential Receiver in Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Stratix® 10 Devices x
2.5.1. Receiver Blocks in Stratix® 10 Devices 2.5.2. Receiver Modes in Stratix® 10 Devices
2.5.1. Receiver Blocks in Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Signal Interface with LVDS SERDES IP 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP and LVDS SERDES IP in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Initialization and Reset 4.3. LVDS SERDES Intel® FPGA IP Timing 4.4. LVDS SERDES Intel® FPGA IP Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES Intel® FPGA IP Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment
4.2.4. Word Boundaries Alignment x
4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES Intel® FPGA IP Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES Intel® FPGA IP Design Examples x
4.4.1. LVDS SERDES IP Synthesizable Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Simulation Design Example 4.4.3. Combined LVDS SERDES IP Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example Generating and Using the Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings 5.2. LVDS SERDES Intel® FPGA IP Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings x
5.1.1. LVDS SERDES Intel® FPGA IP General Settings 5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings 5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings 5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Stratix® 10 High-Speed LVDS I/O Overview
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide

4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example

The dynamic phase shift design example provides you live control over the PLL clock shifts in an LVDS design through a flexible TCL script interface.
Note: The dynamic phase shift design example does not support the duplex mode. If your LVDS SERDES IP uses the Duplex Feature mode, ignore the ed_synth_dps.qsys file generated by the Generate Example Design command.

You can use this example in LVDS-specific applications such as debugging non-DPA receiver capture where you can repeatedly shift the capture clock to find the best operational phase shift.

You can also use the design example as a general example of using the In-System Sources and Probes feature with Signal Tap to interface with your hardware through TCL scripting. This method allows you to use manual switches to test a board without being physically present.

The dynamic phase shift design example uses LVDS SERDES IP parameter settings and connects the IP to an external PLL. The PLL has an exposed dynamic phase shift interface that connects to in-system sources and probes. This connection allows you to control the PLL using the In-System Sources and Probes editor or the provided TCL script in conjunction with Signal Tap.

A part of the LVDS SERDES IP in the design example is also connected to the in-system sources and probes. The provided TCL script shows an example of how you can shift a selected PLL clock and also provides you some utility functions. You can use this example script as a start towards accomplishing the testing function that you want.

Figure 41.  LVDS SERDES IP Dynamic Phase Shift


Generating and Using the Design Example

To generate the combined dynamic phase shift design example from the source files, run the following command in the design example directory: 

quartus_sh -t make_qii_design.tcl -system ed_synth_dps

The TCL script creates a qii_ed_synth_dps directory that contains the ed_synth_dps.qpf project file. You can open and compile this project in the Quartus® Prime software.

To use the provided TCL script to control the in-system sources and probes, run the following command:

quartus_stp -t dps_issp.tcl qii_ed_synth_dps/ed_synth_dps
Note: For the control to work, you must first program the FPGA.

For more information about make_qii_design.tcl arguments, run the following command:

quartus_sh -t make_qii_design.tcl -help
Level Two Title