F-Tile JESD204B Intel® FPGA IP User Guide

Download PDF
ID 723907
Date 4/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. F-Tile JESD204B IP Quick Reference 2. About the F-Tile JESD204B Intel® FPGA IP 3. Getting Started 4. F-Tile JESD204B IP Functional Description 5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines 6. F-Tile JESD204B IP Debug Guidelines 7. F-Tile JESD204B Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide
2. About the F-Tile JESD204B Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. Datapath Modes 2.4. IP Variation 2.5. F-Tile JESD204B IP Configuration 2.6. Channel Bonding 2.7. Performance and Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Intel® FPGA IP Evaluation Mode 3.4. Upgrading IP Cores 3.5. IP Catalog and Parameter Editor 3.6. Design Walkthrough 3.7. F-Tile JESD204B IP Design Considerations 3.8. F-Tile JESD204B Intel® FPGA IP Parameters 3.9. F-Tile JESD204B IP Component Files
3.6. Design Walkthrough x
3.6.1. Creating a New Quartus® Prime Project 3.6.2. Parameterizing and Generating the IP 3.6.3. Compiling the F-Tile JESD204B IP Core Design 3.6.4. Programming an FPGA Device
3.7. F-Tile JESD204B IP Design Considerations x
3.7.1. Integrating the F-Tile JESD204B IP in Platform Designer 3.7.2. Pin Assignments 3.7.3. Adding External System PLL
4. F-Tile JESD204B IP Functional Description x
4.1. Transmitter 4.2. Receiver 4.3. Operation 4.4. Clocking Scheme 4.5. Reset Scheme 4.6. Signals 4.7. Registers
4.1. Transmitter x
4.1.1. TX Data Link Layer 4.1.2. TX PHY Layer
4.1.1. TX Data Link Layer x
4.1.1.1. TX CGS 4.1.1.2. TX ILAS 4.1.1.3. User Data Phase
4.2. Receiver x
4.2.1. RX Data Link Layer 4.2.2. RX PHY Layer
4.2.1. RX Data Link Layer x
4.2.1.1. RX CGS 4.2.1.2. Frame Synchronization 4.2.1.3. Frame Alignment 4.2.1.4. Lane Alignment 4.2.1.5. ILAS Data 4.2.1.6. Initial Lane Synchronization
4.3. Operation x
4.3.1. Operating Modes 4.3.2. Scrambler/Descrambler 4.3.3. SYNC_N Signal 4.3.4. Link Reinitialization 4.3.5. Link Startup Sequence 4.3.6. Error Reporting Through SYNC_N Signal
4.3.1. Operating Modes x
4.3.1.1. Subclass 0 Operating Mode 4.3.1.2. Subclass 1 Operating Mode 4.3.1.3. Subclass 2 Operating Mode
4.4. Clocking Scheme x
4.4.1. Device Clock 4.4.2. Link Clock 4.4.3. Local MultiFrame Clock 4.4.4. Clock Correlation 4.4.5. System PLL Clock
4.5. Reset Scheme x
4.5.1. Reset Sequence 4.5.2. ADC–FPGA Subsystem Reset Sequence 4.5.3. FPGA–DAC Subsystem Reset Sequence
4.6. Signals x
4.6.1. Transmitter Signals 4.6.2. Receiver Signals
4.7. Registers x
4.7.1. Register Access Type Convention 4.7.2. Register Map and Definition 4.7.3. Transmitter Registers 4.7.4. Receiver Registers
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines x
5.1. Constraining Incoming SYSREF Signal 5.2. Programmable RBD Offset 5.3. Programmable LMFC Offset 5.4. Maintaining Deterministic Latency during Link Reinitialization
6. F-Tile JESD204B IP Debug Guidelines x
6.1. Clocking Scheme 6.2. F-Tile JESD204B Parameters 6.3. SPI Programming 6.4. Converter and FPGA Operating Conditions 6.5. Signal Polarity and FPGA Pin Assignment
1. F-Tile JESD204B IP Quick Reference
2. About the F-Tile JESD204B Intel® FPGA IP
3. Getting Started
4. F-Tile JESD204B IP Functional Description
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines
6. F-Tile JESD204B IP Debug Guidelines
7. F-Tile JESD204B Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide

3.7.2. Pin Assignments

Set the pin assignments before you compile to provide direction to the Quartus® Prime software Fitter tool. You must also specify the signals that should be assigned to device I/O pins.
You can create virtual pins to avoid making specific pin assignments for top-level signals. This is useful when you want to perform compilation, but are not ready to map the design to hardware. Intel® recommends that you create virtual pins for all unused top-level signals to improve timing closure.
Note: Do not create virtual pins for the clock or reset signals.

For F-tile devices, use the F-tile Channel Channel Placement tool to assist you in making pin assignments. Specify the transceiver mode and PMA direct NRZ.

Related Information
Level Two Title