F-Tile JESD204B Intel® FPGA IP User Guide

Download PDF
ID 723907
Date 4/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. F-Tile JESD204B IP Quick Reference 2. About the F-Tile JESD204B Intel® FPGA IP 3. Getting Started 4. F-Tile JESD204B IP Functional Description 5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines 6. F-Tile JESD204B IP Debug Guidelines 7. F-Tile JESD204B Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide
2. About the F-Tile JESD204B Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. Datapath Modes 2.4. IP Variation 2.5. F-Tile JESD204B IP Configuration 2.6. Channel Bonding 2.7. Performance and Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Intel® FPGA IP Evaluation Mode 3.4. Upgrading IP Cores 3.5. IP Catalog and Parameter Editor 3.6. Design Walkthrough 3.7. F-Tile JESD204B IP Design Considerations 3.8. F-Tile JESD204B Intel® FPGA IP Parameters 3.9. F-Tile JESD204B IP Component Files
3.6. Design Walkthrough x
3.6.1. Creating a New Quartus® Prime Project 3.6.2. Parameterizing and Generating the IP 3.6.3. Compiling the F-Tile JESD204B IP Core Design 3.6.4. Programming an FPGA Device
3.7. F-Tile JESD204B IP Design Considerations x
3.7.1. Integrating the F-Tile JESD204B IP in Platform Designer 3.7.2. Pin Assignments 3.7.3. Adding External System PLL
4. F-Tile JESD204B IP Functional Description x
4.1. Transmitter 4.2. Receiver 4.3. Operation 4.4. Clocking Scheme 4.5. Reset Scheme 4.6. Signals 4.7. Registers
4.1. Transmitter x
4.1.1. TX Data Link Layer 4.1.2. TX PHY Layer
4.1.1. TX Data Link Layer x
4.1.1.1. TX CGS 4.1.1.2. TX ILAS 4.1.1.3. User Data Phase
4.2. Receiver x
4.2.1. RX Data Link Layer 4.2.2. RX PHY Layer
4.2.1. RX Data Link Layer x
4.2.1.1. RX CGS 4.2.1.2. Frame Synchronization 4.2.1.3. Frame Alignment 4.2.1.4. Lane Alignment 4.2.1.5. ILAS Data 4.2.1.6. Initial Lane Synchronization
4.3. Operation x
4.3.1. Operating Modes 4.3.2. Scrambler/Descrambler 4.3.3. SYNC_N Signal 4.3.4. Link Reinitialization 4.3.5. Link Startup Sequence 4.3.6. Error Reporting Through SYNC_N Signal
4.3.1. Operating Modes x
4.3.1.1. Subclass 0 Operating Mode 4.3.1.2. Subclass 1 Operating Mode 4.3.1.3. Subclass 2 Operating Mode
4.4. Clocking Scheme x
4.4.1. Device Clock 4.4.2. Link Clock 4.4.3. Local MultiFrame Clock 4.4.4. Clock Correlation Example 1 Example 2 Example 3 4.4.5. System PLL Clock
4.5. Reset Scheme x
4.5.1. Reset Sequence 4.5.2. ADC–FPGA Subsystem Reset Sequence 4.5.3. FPGA–DAC Subsystem Reset Sequence
4.6. Signals x
4.6.1. Transmitter Signals 4.6.2. Receiver Signals
4.7. Registers x
4.7.1. Register Access Type Convention 4.7.2. Register Map and Definition 4.7.3. Transmitter Registers 4.7.4. Receiver Registers
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines x
5.1. Constraining Incoming SYSREF Signal 5.2. Programmable RBD Offset 5.3. Programmable LMFC Offset 5.4. Maintaining Deterministic Latency during Link Reinitialization
6. F-Tile JESD204B IP Debug Guidelines x
6.1. Clocking Scheme 6.2. F-Tile JESD204B Parameters 6.3. SPI Programming 6.4. Converter and FPGA Operating Conditions 6.5. Signal Polarity and FPGA Pin Assignment
1. F-Tile JESD204B IP Quick Reference
2. About the F-Tile JESD204B Intel® FPGA IP
3. Getting Started
4. F-Tile JESD204B IP Functional Description
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines
6. F-Tile JESD204B IP Debug Guidelines
7. F-Tile JESD204B Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide

4.4.4. Clock Correlation

This section describes the clock correlation between the device clock, link clock, frame clock, and local multiframe clock.

Example 1

Targeted Device with LMF=222, K=16 and Data rate = 6.5 Gbps

Device Clock Selected = 325 MHz (obtained during IP core generation)

Link Clock = 6.5 GHz/40 = 162.5 MHz

Frame Clock = 6.5 GHz/(10x2) = 325 MHz

Local Multiframe Clock = 325 MHz / 16 = 20.3125 MHz

SYSREF Frequency = Local Multiframe Clock / n; (n = integer; 1, 2, …)

Local Multiframe Clock Counter = (F × K/4) = (2×16/4) = 8 link clocks 6

Example 2

Targeted Device with LMF=244, K=16 and Data rate = 5.0 Gbps

Device Clock Selected = 125 MHz (obtained during IP core generation)

Link Clock = 5 GHz/40 = 125 MHz 7

Frame Clock = 5 GHz /(10×4) = 125 MHz 7

Local Multiframe Clock = 125 MHz / 16 = 7.8125 MHz

SYSREF Frequency = Local Multiframe Clock / n; (n = integer; 1, 2, …)

Local Multiframe Clock Counter = (F × K/4) = (4×16/4) = 16 link clocks 6

Example 3

Targeted Device with LMF=421, K=32 and Data rate = 10.0 Gbps

Device Clock Selected = 250 MHz (obtained during IP core generation)

Link Clock = 10 GHz/40 = 250 MHz

Frame Clock = 10 GHz/(10×1) = 1 GHz8

Local Multiframe Clock = 1 GHz / 32 = 31.25 MHz

SYSREF Frequency = Local Multiframe Clock / n; (n = integer; 1, 2, …)

Local Multiframe Clock Counter = (F × K/4) = (1×32/4) = 8 link clocks 6

Related Information
6 Eight link clocks mean that the local multiframe clock counts from values 0 to 7 and then loops back to 0.
7 The link clock and frame clock are running at the same frequency. You only need to generate one clock from the Intel® FPGA IO PLL IP core.
8 In this example, the frame clock may not be able to run up to 1 GHz in the FPGA fabric. The JESD204B transport layer in the design example supports running the data stream of half rate (1 GHz/2 = 500 MHz), at two times the data bus width or of quarter rate (1GHz/4 = 250 MHz), at four times the data bus width.
Level Two Title