Cyclone V Device Datasheet

Download PDF
ID 683801
Date 5/23/2023
Public
Document Table of Contents
Document Table of Contents x
Cyclone V Device Datasheet
Cyclone V Device Datasheet x
Electrical Characteristics Switching Characteristics Configuration Specifications I/O Timing Glossary Document Revision History for Cyclone® V Device Datasheet
Electrical Characteristics x
Operating Conditions
Operating Conditions x
Absolute Maximum Ratings Maximum Allowed Overshoot and Undershoot Voltage Recommended Operating Conditions DC Characteristics I/O Standard Specifications
Recommended Operating Conditions x
Recommended Operating Conditions Transceiver Power Supply Operating Conditions HPS Power Supply Operating Conditions
DC Characteristics x
Supply Current and Power Consumption I/O Pin Leakage Current Bus Hold Specifications OCT Calibration Accuracy Specifications OCT Without Calibration Resistance Tolerance Specifications OCT Variation after Power-Up Calibration Pin Capacitance Hot Socketing Internal Weak Pull-Up Resistor
I/O Standard Specifications x
Single-Ended I/O Standards Single-Ended SSTL, HSTL, and HSUL I/O Reference Voltage Specifications Single-Ended SSTL, HSTL, and HSUL I/O Standards Signal Specifications Differential SSTL I/O Standards Differential HSTL and HSUL I/O Standards Differential I/O Standard Specifications
Switching Characteristics x
Transceiver Performance Specifications Core Performance Specifications Periphery Performance HPS Specifications
Transceiver Performance Specifications x
Transceiver Specifications for Cyclone V GX, GT, SX, and ST Devices CTLE Response at Data Rates > 3.25 Gbps across Supported AC Gain and DC Gain CTLE Response at Data Rates ≤ 3.25 Gbps across Supported AC Gain and DC Gain Typical TX VOD Setting for Cyclone® V Transceiver Channels with termination of 100 Ω Transmitter Pre-Emphasis Levels Transceiver Compliance Specification
Core Performance Specifications x
Clock Tree Specifications PLL Specifications DSP Block Performance Specifications Memory Block Performance Specifications
Periphery Performance x
High-Speed I/O Specifications DLL Frequency Range Specifications DQS Logic Block Specifications Memory Output Clock Jitter Specifications OCT Calibration Block Specifications Duty Cycle Distortion (DCD) Specifications
HPS Specifications x
HPS Clock Performance HPS PLL Specifications Quad SPI Flash Timing Characteristics SPI Timing Characteristics SD/MMC Timing Characteristics USB Timing Characteristics Ethernet Media Access Controller (EMAC) Timing Characteristics I2C Timing Characteristics NAND Timing Characteristics Arm* Trace Timing Characteristics UART Interface GPIO Interface CAN Interface HPS JTAG Timing Specifications
HPS PLL Specifications x
HPS PLL VCO Frequency Range HPS PLL Input Clock Range HPS PLL Input Jitter
Configuration Specifications x
POR Specifications FPGA JTAG Configuration Timing FPP Configuration Timing Active Serial (AS) Configuration Timing DCLK Frequency Specification in the AS Configuration Scheme Passive Serial (PS) Configuration Timing Initialization Configuration Files Minimum Configuration Time Estimation Remote System Upgrades User Watchdog Internal Oscillator Frequency Specifications
FPP Configuration Timing x
DCLK-to-DATA[] Ratio (r) for FPP Configuration FPP Configuration Timing when DCLK-to-DATA[] = 1 FPP Configuration Timing when DCLK-to-DATA[] >1
I/O Timing x
Programmable IOE Delay Programmable Output Buffer Delay
Cyclone V Device Datasheet

NAND Timing Characteristics

Table 52.  NAND ONFI 1.0 Timing Requirements for Cyclone® V DevicesThe NAND controller supports Open NAND FLASH Interface (ONFI) 1.0 Mode 5 timing as well as legacy NAND devices. This table lists the requirements for ONFI 1.0 mode 5 timing. The HPS NAND controller can meet this timing by programming the C4 output of the main HPS PLL and timing registers provided in the NAND controller.
Symbol Description Min Max Unit
Twp 72 Write enable pulse width 10 — ns
Twh 72 Write enable hold time 7 — ns
Trp 72 Read enable pulse width 10 — ns
Treh 72 Read enable hold time 7 — ns
Tclesu 72 Command latch enable to write enable setup time 10 — ns
Tcleh 72 Command latch enable to write enable hold time 5 — ns
Tcesu 72 Chip enable to write enable setup time 15 — ns
Tceh 72 Chip enable to write enable hold time 5 — ns
Talesu 72 Address latch enable to write enable setup time 10 — ns
Taleh 72 Address latch enable to write enable hold time 5 — ns
Tdsu 72 Data to write enable setup time 10 — ns
Tdh 72 Data to write enable hold time 5 — ns
Tcea Chip enable to data access time — 25 ns
Trea Read enable to data access time — 16 ns
Trhz Read enable to data high impedance — 100 ns
Trr Ready to read enable low 20 — ns
Figure 15. NAND Command Latch Timing Diagram


Figure 16. NAND Address Latch Timing Diagram


Figure 17. NAND Data Write Timing Diagram


Figure 18. NAND Data Read Timing Diagram


72 Timing of the NAND interface is controlled through the NAND configuration registers.
Level Two Title