Cyclone V Device Datasheet

Download PDF
ID 683801
Date 5/23/2023
Public
Document Table of Contents
Document Table of Contents x
Cyclone V Device Datasheet
Cyclone V Device Datasheet x
Electrical Characteristics Switching Characteristics Configuration Specifications I/O Timing Glossary Document Revision History for Cyclone® V Device Datasheet
Electrical Characteristics x
Operating Conditions
Operating Conditions x
Absolute Maximum Ratings Maximum Allowed Overshoot and Undershoot Voltage Recommended Operating Conditions DC Characteristics I/O Standard Specifications
Recommended Operating Conditions x
Recommended Operating Conditions Transceiver Power Supply Operating Conditions HPS Power Supply Operating Conditions
DC Characteristics x
Supply Current and Power Consumption I/O Pin Leakage Current Bus Hold Specifications OCT Calibration Accuracy Specifications OCT Without Calibration Resistance Tolerance Specifications OCT Variation after Power-Up Calibration Pin Capacitance Hot Socketing Internal Weak Pull-Up Resistor
I/O Standard Specifications x
Single-Ended I/O Standards Single-Ended SSTL, HSTL, and HSUL I/O Reference Voltage Specifications Single-Ended SSTL, HSTL, and HSUL I/O Standards Signal Specifications Differential SSTL I/O Standards Differential HSTL and HSUL I/O Standards Differential I/O Standard Specifications
Switching Characteristics x
Transceiver Performance Specifications Core Performance Specifications Periphery Performance HPS Specifications
Transceiver Performance Specifications x
Transceiver Specifications for Cyclone V GX, GT, SX, and ST Devices CTLE Response at Data Rates > 3.25 Gbps across Supported AC Gain and DC Gain CTLE Response at Data Rates ≤ 3.25 Gbps across Supported AC Gain and DC Gain Typical TX VOD Setting for Cyclone® V Transceiver Channels with termination of 100 Ω Transmitter Pre-Emphasis Levels Transceiver Compliance Specification
Core Performance Specifications x
Clock Tree Specifications PLL Specifications DSP Block Performance Specifications Memory Block Performance Specifications
Periphery Performance x
High-Speed I/O Specifications DLL Frequency Range Specifications DQS Logic Block Specifications Memory Output Clock Jitter Specifications OCT Calibration Block Specifications Duty Cycle Distortion (DCD) Specifications
HPS Specifications x
HPS Clock Performance HPS PLL Specifications Quad SPI Flash Timing Characteristics SPI Timing Characteristics SD/MMC Timing Characteristics USB Timing Characteristics Ethernet Media Access Controller (EMAC) Timing Characteristics I2C Timing Characteristics NAND Timing Characteristics Arm* Trace Timing Characteristics UART Interface GPIO Interface CAN Interface HPS JTAG Timing Specifications
HPS PLL Specifications x
HPS PLL VCO Frequency Range HPS PLL Input Clock Range HPS PLL Input Jitter
Configuration Specifications x
POR Specifications FPGA JTAG Configuration Timing FPP Configuration Timing Active Serial (AS) Configuration Timing DCLK Frequency Specification in the AS Configuration Scheme Passive Serial (PS) Configuration Timing Initialization Configuration Files Minimum Configuration Time Estimation Remote System Upgrades User Watchdog Internal Oscillator Frequency Specifications
FPP Configuration Timing x
DCLK-to-DATA[] Ratio (r) for FPP Configuration FPP Configuration Timing when DCLK-to-DATA[] = 1 FPP Configuration Timing when DCLK-to-DATA[] >1
I/O Timing x
Programmable IOE Delay Programmable Output Buffer Delay
Cyclone V Device Datasheet

FPP Configuration Timing when DCLK-to-DATA[] = 1

When you enable decompression or the design security feature, the DCLK-to-DATA[] ratio varies for FPP ×8 and FPP ×16. For the respective DCLK-to-DATA[] ratio, refer to the DCLK-to-DATA[] Ratio for Cyclone® V Devices table.

Table 58.  FPP Timing Parameters When DCLK-to-DATA[] Ratio is 1 for Cyclone® V DevicesThe specifications in this table are not applicable to Cyclone® V QS package.
Symbol Parameter Minimum Maximum Unit
tCF2CD nCONFIG low to CONF_DONE low — 600 ns
tCF2ST0 nCONFIG low to nSTATUS low — 600 ns
tCFG nCONFIG low pulse width 2 — µs
tSTATUS nSTATUS low pulse width 268 150677 µs
tCF2ST1 nCONFIG high to nSTATUS high — 150678 µs
tCF2CK 79 nCONFIG high to first rising edge on DCLK 1506 — µs
tST2CK 79 nSTATUS high to first rising edge of DCLK 2 — µs
tDSU DATA[] setup time before rising edge on DCLK 5.5 — ns
tDH DATA[] hold time after rising edge on DCLK 0 — ns
tCH DCLK high time 0.45 × 1/fMAX — s
tCL DCLK low time 0.45 × 1/fMAX — s
tCLK DCLK period 1/fMAX — s
fMAX DCLK frequency (FPP ×8/ ×16) — 125 MHz
tCD2UM CONF_DONE high to user mode80 175 437 µs
tCD2CU CONF_DONE high to CLKUSR enabled 4× maximum DCLK period — —
tCD2UMC CONF_DONE high to user mode with CLKUSR option on tCD2CU + (Tinit × CLKUSR period) — —
Tinit Number of clock cycles required for device initialization 8,576 — Cycles
Related Information
77 You can obtain this value if you do not delay configuration by extending the nCONFIG or the nSTATUS low pulse width.
78 You can obtain this value if you do not delay configuration by externally holding the nSTATUS low.
79 If nSTATUS is monitored, follow the tST2CK specification. If nSTATUS is not monitored, follow the tCF2CK specification.
80 The minimum and maximum numbers apply only if you chose the internal oscillator as the clock source for initializing the device.
Level Two Title