CPRI Intel® FPGA IP User Guide

Download PDF
ID 683595
Date 5/17/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the CPRI Intel® FPGA IP 2. Getting Started with the CPRI Intel® FPGA IP 3. CPRI IP Functional Description 4. CPRI Intel® FPGA IP Signals 5. CPRI Intel® FPGA IP Registers 6. CPRI Intel® FPGA IP User Guide Archives 7. Document Revision History for the CPRI Intel® FPGA IP User Guide
1. About the CPRI Intel® FPGA IP x
1.1. CPRI Intel® FPGA IP Core Supported Features 1.2. CPRI Intel® FPGA IP Device Family and Speed Grade Support 1.3. Intel® FPGA IP Verification 1.4. Resource Utilization for CPRI Intel® FPGA IP 1.5. CPRI IP Release Information
1.2. CPRI Intel® FPGA IP Device Family and Speed Grade Support x
1.2.1. CPRI IP Device Family Support 1.2.2. CPRI Intel® FPGA IP Device and Transceiver Speed Grade Support
2. Getting Started with the CPRI Intel® FPGA IP x
2.1. Installation and Licensing 2.2. Generating aCPRI Intel® FPGA IP 2.3. CPRI Intel® FPGA IP Generated Files 2.4. CPRI Intel® FPGA IP Parameters 2.5. Integrating the CPRI IP into your Design: Required External Blocks 2.6. Simulating Intel FPGA IP Cores 2.7. Running the CPRI IP Design Example 2.8. CPRI Design Example Clocks 2.9. About the Testbench 2.10. Compiling the Full Design and Programming the FPGA
2.1. Installation and Licensing x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating the CPRI IP into your Design: Required External Blocks x
2.5.1. Adding the Transceiver TX PLL IP Core 2.5.2. Adding the Reset Controller 2.5.3. Adding the Transceiver Reconfiguration Controller 2.5.4. Adding the Off-Chip Clean-Up PLL 2.5.5. Adding and Connecting the Single-Trip Delay Calibration Blocks 2.5.6. CPRI IP Transceiver PLL Calibration 2.5.7. Reference and System PLL Clock for your IP Design
2.5.7. Reference and System PLL Clock for your IP Design x
2.5.7.1. System PLL Connections for the Agilex® 7 F-tile Variations 2.5.7.2. System PLL Connections for the Agilex 5 Variations 2.5.7.3. Reset Sequencer Connections for the Agilex 5 Variations
3. CPRI IP Functional Description x
3.1. Interfaces Overview 3.2. CPRI Intel® FPGA IP Clocking Structure 3.3. CPRI Intel® FPGA IP Core Reset Requirements 3.4. Start-Up Sequence Following Reset 3.5. AUX Interface 3.6. Direct IQ Interface 3.7. Ctrl_AxC Interface 3.8. Direct Vendor Specific Access Interface 3.9. Real-Time Vendor Specific Interface 3.10. Direct HDLC Serial Interface 3.11. Direct L1 Control and Status Interface 3.12. L1 Debug Interface 3.13. Media Independent Interface (MII) to External Ethernet Block 3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block 3.15. CPU Interface to CPRI Intel® FPGA IP Registers 3.16. Auto-Rate Negotiation 3.17. Extended Delay Measurement 3.18. Deterministic Latency and Delay Measurement and Calibration 3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces 3.20. Testing Features
3.2. CPRI Intel® FPGA IP Clocking Structure x
3.2.1. Example CPRI Intel® FPGA IP Core Clock Connections in Different Clocking Modes
3.4. Start-Up Sequence Following Reset x
3.4.1. Start-Up Sequence Interface Signals
3.5. AUX Interface x
3.5.1. AUX Interface Signals 3.5.2. AUX Interface Synchronization 3.5.3. Auxiliary Latency Cycles 3.5.4. Direct Interface CPRI Frame Data Format
3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block x
3.14.1. GMII Normal Mode 3.14.2. Ethernet PCS Bypass Mode 3.14.3. Ethernet PCS Run-Time Switching
3.15. CPU Interface to CPRI Intel® FPGA IP Registers x
3.15.1. CPU Interface Signals 3.15.2. Accessing the Hyperframe Control Words
3.15.2. Accessing the Hyperframe Control Words x
3.15.2.1. Specifying the Control Word 3.15.2.2. Specifying the Position in the Control Word 3.15.2.3. Retrieving the Hyperframe Control Words 3.15.2.4. Writing the Hyperframe Control Words
3.17. Extended Delay Measurement x
3.17.1. Extended Delay Measurement for Soft Internal Buffers 3.17.2. Extended Delay Measurement for Stratix® 10 Hard FIFOs 3.17.3. Extended Delay Measurement Interface
3.18. Deterministic Latency and Delay Measurement and Calibration x
3.18.1. Delay Measurement and Calibration Features 3.18.2. Delay Requirements 3.18.3. Single-Hop Delay Measurement 3.18.4. Multi-Hop Delay Measurement 3.18.5. Delay Calibration Features
3.18.3. Single-Hop Delay Measurement x
3.18.3.1. Rx Path Delay 3.18.3.2. Tx Path Delay 3.18.3.3. Round-Trip Delay
3.18.5. Delay Calibration Features x
3.18.5.1. Single-Trip Delay Calibration 3.18.5.2. Round-Trip Delay Calibration 3.18.5.3. Tx Bitslip Delay
3.18.5.1. Single-Trip Delay Calibration x
3.18.5.1.1. Single-Trip Latency Measurement and Calibration Interface Signals
3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces x
3.19.1. CPRI Link 3.19.2. Main Transceiver Clock and Reset Signals 3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface 3.19.4. Arria® 10, Stratix® 10, and Agilex® 7 Transceiver Reconfiguration Interface 3.19.5. RS-FEC Interface 3.19.6. Interface to the External Reset Controller 3.19.7. Interface to the External PLL 3.19.8. Transceiver Debug Interface
3.20. Testing Features x
3.20.1. CPRI Intel® FPGA IP Core Loopback Modes 3.20.2. CPRI Intel® FPGA IP Core Self-Synchronization Feature
4. CPRI Intel® FPGA IP Signals x
4.1. CPRI Intel® FPGA IP Core L2 Interface 4.2. CPRI Intel® FPGA IP Core L1 Direct Access Interfaces 4.3. CPRI Intel® FPGA IP Core Management Interfaces 4.4. CPRI Intel® FPGA IP Core Transceiver and Transceiver Management Signals
1. About the CPRI Intel® FPGA IP
2. Getting Started with the CPRI Intel® FPGA IP
3. CPRI IP Functional Description
4. CPRI Intel® FPGA IP Signals
5. CPRI Intel® FPGA IP Registers
6. CPRI Intel® FPGA IP User Guide Archives
7. Document Revision History for the CPRI Intel® FPGA IP User Guide

3.4.1. Start-Up Sequence Interface Signals

After reset, if you turned on Enable start-up sequence state machine in the CPRI Intel® FPGA IP, the internal state machine performs link synchronization and other initialization tasks. If you did not turn on Enable start-up sequence state machine, user logic must perform these functions.

The signals visible in the interface depend on whether or not you turned on Enable start-up sequence state machine.

Table 23.  Start-Up Sequence Interface Signals

All interface signals are clocked by the cpri_clkout clock.

Signal Name

Direction

Description

state_startup_seq[2:0] Output Indicates the state of the CPRI start-up sequence state machine. This signal has the following valid values:
  • 3'b000: State A: Standby
  • 3'b001: State B: L1 Synchronization
  • 3'b011: State C: Protocol Setup
  • 3'b010: State D: Control and Management Setup
  • 3'b110: State E: Interface and VSS Negotiation
  • 3'b111: State F: Operation
  • 3'b101: State G: Passive Link

This signal is available only if you turn on Enable start-up sequence state machine in the CPRI parameter editor.

state_l1_synch[2:0] Output State B condition indicator. Indicates the state of the CPRI receiver L1 synchronization state machine. This signal has the following valid values:
  • 3'b000: XACQ1
  • 3'b001: XACQ2
  • 3'b011: XSYNC1
  • 3'b010: XSYNC2
  • 3'b110: HFNSYNC
nego_bitrate_complete Input Indicates the CPRI line bit rate negotiation is complete. Input from external CPRI line bit rate negotiation block.

If you do not turn on Enable line bit rate auto-negotiation in the CPRI parameter editor, you should tie this signal high.

This signal is available only if you turn on Enable start-up sequence state machine in the CPRI parameter editor.

Asserting this signal advances the start-up sequence state machine from state B to state C. The IP core writes the value of this signal to the nego_bitrate_complete field of the START_UP_SEQ register at offset 0x24.

nego_protocol_complete Input

Indicates the CPRI protocol version negotiation is complete.

This signal is available only if you turn on Enable start-up sequence state machine in the CPRI parameter editor.

Asserting this signal advances the start-up sequence state machine from state C to state D. The IP core writes the value of this signal to the nego_protocol_complete field of the START_UP_SEQ register at offset 0x24.

nego_cm_complete Input

Indicates the Control and Management negotiation is complete.

This signal is available only if you turn on Enable start-up sequence state machine in the CPRI parameter editor.

Asserting this signal advances the start-up sequence state machine from state D to state E. The IP core writes the value of this signal to the nego_cm_complete field of the START_UP_SEQ register at offset 0x24.

nego_vss_complete Input

Indicates the Vendor Specific negotiation is complete.

This signal is available only if you turn on Enable start-up sequence state machine in the CPRI parameter editor.

Asserting this signal advances the start-up sequence state machine from state E to state F. The IP core writes the value of this signal to the nego_vss_complete field of the START_UP_SEQ register at offset 0x24.

nego_l1_timer_expired Input If you do not turn on Enable protocol version and C&M channel setting auto-negotiation in the CPRI parameter editor, drive this signal from your user-defined L1 timer to indicate that the L1 timer has expired.

Note that if you do not turn on Enable protocol version and C&M channel setting auto-negotiation, user logic is expected to maintain an L1 timer outside the IP core.

This signal is available only if you turn on Enable start-up sequence state machine in the CPRI parameter editor.

If you also turn on Enable protocol version and C&M channel setting auto-negotiation in the CPRI parameter editor, you should tie this signal low so it does not interfere with the internal L1 timer.

Figure 27. Start-Up Sequence State Machine Timing Diagram


Level Two Title