CPRI Intel® FPGA IP User Guide

Download PDF
ID 683595
Date 5/17/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the CPRI Intel® FPGA IP 2. Getting Started with the CPRI Intel® FPGA IP 3. CPRI IP Functional Description 4. CPRI Intel® FPGA IP Signals 5. CPRI Intel® FPGA IP Registers 6. CPRI Intel® FPGA IP User Guide Archives 7. Document Revision History for the CPRI Intel® FPGA IP User Guide
1. About the CPRI Intel® FPGA IP x
1.1. CPRI Intel® FPGA IP Core Supported Features 1.2. CPRI Intel® FPGA IP Device Family and Speed Grade Support 1.3. Intel® FPGA IP Verification 1.4. Resource Utilization for CPRI Intel® FPGA IP 1.5. CPRI IP Release Information
1.2. CPRI Intel® FPGA IP Device Family and Speed Grade Support x
1.2.1. CPRI IP Device Family Support 1.2.2. CPRI Intel® FPGA IP Device and Transceiver Speed Grade Support
2. Getting Started with the CPRI Intel® FPGA IP x
2.1. Installation and Licensing 2.2. Generating aCPRI Intel® FPGA IP 2.3. CPRI Intel® FPGA IP Generated Files 2.4. CPRI Intel® FPGA IP Parameters 2.5. Integrating the CPRI IP into your Design: Required External Blocks 2.6. Simulating Intel FPGA IP Cores 2.7. Running the CPRI IP Design Example 2.8. CPRI Design Example Clocks 2.9. About the Testbench 2.10. Compiling the Full Design and Programming the FPGA
2.1. Installation and Licensing x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating the CPRI IP into your Design: Required External Blocks x
2.5.1. Adding the Transceiver TX PLL IP Core 2.5.2. Adding the Reset Controller 2.5.3. Adding the Transceiver Reconfiguration Controller 2.5.4. Adding the Off-Chip Clean-Up PLL 2.5.5. Adding and Connecting the Single-Trip Delay Calibration Blocks 2.5.6. CPRI IP Transceiver PLL Calibration 2.5.7. Reference and System PLL Clock for your IP Design
2.5.7. Reference and System PLL Clock for your IP Design x
2.5.7.1. System PLL Connections for the Agilex® 7 F-tile Variations 2.5.7.2. System PLL Connections for the Agilex 5 Variations 2.5.7.3. Reset Sequencer Connections for the Agilex 5 Variations
3. CPRI IP Functional Description x
3.1. Interfaces Overview 3.2. CPRI Intel® FPGA IP Clocking Structure 3.3. CPRI Intel® FPGA IP Core Reset Requirements 3.4. Start-Up Sequence Following Reset 3.5. AUX Interface 3.6. Direct IQ Interface 3.7. Ctrl_AxC Interface 3.8. Direct Vendor Specific Access Interface 3.9. Real-Time Vendor Specific Interface 3.10. Direct HDLC Serial Interface 3.11. Direct L1 Control and Status Interface 3.12. L1 Debug Interface 3.13. Media Independent Interface (MII) to External Ethernet Block 3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block 3.15. CPU Interface to CPRI Intel® FPGA IP Registers 3.16. Auto-Rate Negotiation 3.17. Extended Delay Measurement 3.18. Deterministic Latency and Delay Measurement and Calibration 3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces 3.20. Testing Features
3.2. CPRI Intel® FPGA IP Clocking Structure x
3.2.1. Example CPRI Intel® FPGA IP Core Clock Connections in Different Clocking Modes
3.4. Start-Up Sequence Following Reset x
3.4.1. Start-Up Sequence Interface Signals
3.5. AUX Interface x
3.5.1. AUX Interface Signals 3.5.2. AUX Interface Synchronization 3.5.3. Auxiliary Latency Cycles 3.5.4. Direct Interface CPRI Frame Data Format
3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block x
3.14.1. GMII Normal Mode 3.14.2. Ethernet PCS Bypass Mode 3.14.3. Ethernet PCS Run-Time Switching
3.15. CPU Interface to CPRI Intel® FPGA IP Registers x
3.15.1. CPU Interface Signals 3.15.2. Accessing the Hyperframe Control Words
3.15.2. Accessing the Hyperframe Control Words x
3.15.2.1. Specifying the Control Word 3.15.2.2. Specifying the Position in the Control Word 3.15.2.3. Retrieving the Hyperframe Control Words 3.15.2.4. Writing the Hyperframe Control Words
3.17. Extended Delay Measurement x
3.17.1. Extended Delay Measurement for Soft Internal Buffers 3.17.2. Extended Delay Measurement for Stratix® 10 Hard FIFOs 3.17.3. Extended Delay Measurement Interface
3.18. Deterministic Latency and Delay Measurement and Calibration x
3.18.1. Delay Measurement and Calibration Features 3.18.2. Delay Requirements 3.18.3. Single-Hop Delay Measurement 3.18.4. Multi-Hop Delay Measurement 3.18.5. Delay Calibration Features
3.18.3. Single-Hop Delay Measurement x
3.18.3.1. Rx Path Delay 3.18.3.2. Tx Path Delay 3.18.3.3. Round-Trip Delay
3.18.5. Delay Calibration Features x
3.18.5.1. Single-Trip Delay Calibration 3.18.5.2. Round-Trip Delay Calibration 3.18.5.3. Tx Bitslip Delay
3.18.5.1. Single-Trip Delay Calibration x
3.18.5.1.1. Single-Trip Latency Measurement and Calibration Interface Signals
3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces x
3.19.1. CPRI Link 3.19.2. Main Transceiver Clock and Reset Signals 3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface 3.19.4. Arria® 10, Stratix® 10, and Agilex® 7 Transceiver Reconfiguration Interface 3.19.5. RS-FEC Interface 3.19.6. Interface to the External Reset Controller 3.19.7. Interface to the External PLL 3.19.8. Transceiver Debug Interface
3.20. Testing Features x
3.20.1. CPRI Intel® FPGA IP Core Loopback Modes 3.20.2. CPRI Intel® FPGA IP Core Self-Synchronization Feature
4. CPRI Intel® FPGA IP Signals x
4.1. CPRI Intel® FPGA IP Core L2 Interface 4.2. CPRI Intel® FPGA IP Core L1 Direct Access Interfaces 4.3. CPRI Intel® FPGA IP Core Management Interfaces 4.4. CPRI Intel® FPGA IP Core Transceiver and Transceiver Management Signals
1. About the CPRI Intel® FPGA IP
2. Getting Started with the CPRI Intel® FPGA IP
3. CPRI IP Functional Description
4. CPRI Intel® FPGA IP Signals
5. CPRI Intel® FPGA IP Registers
6. CPRI Intel® FPGA IP User Guide Archives
7. Document Revision History for the CPRI Intel® FPGA IP User Guide

2.3. CPRI Intel® FPGA IP Generated Files

The Quartus® Prime software generates the following IP output files.
Table 8.  IP Generated Files

File Name

Description

<your_ip>.ip ( Quartus® Prime Pro Edition only)

Top-level IP variation file. <your_ip> is the name that you give your IP variation.

your_ip>.qsys ( Quartus® Prime Standard Edition only)

<system>.sopcinfo

Describes the connections and IP component parameterizations in your Platform Designer system. You can parse its contents to get requirements when you develop software drivers for IP components. ( Quartus® Prime Standard Edition only)

Downstream tools such as the Intel® Nios® II tool chain use this file. The .sopcinfo file and the system.h file generated for the Nios® II tool chain include address map information for each slave relative to each master that accesses the slave. Different masters may have a different address map to access a particular slave component.

<your_ip>.cmp The VHDL Component Declaration (.cmp) file is a text file that contains local generic and port definitions that you can use in VHDL design files.
<your_ip>.html

A report that contains connection information, a memory map showing the address of each slave with respect to each master to which it is connected, and parameter assignments.

<your_ip>_generation.rpt IP or Platform Designer generation log file. A summary of the messages during IP generation.
<your_ip>.debuginfo Contains post-generation information. Used to pass System Console and Bus Analyzer Toolkit information about the Platform Designer (Standard) interconnect. The Bus Analysis Toolkit uses this file to identify debug components in the Platform Designer (Standard) interconnect. ( Quartus® Prime Standard Edition only)
<your_ip>.qgsimc Lists simulation parameters to support incremental regeneration. ( Quartus® Prime Pro Edition only)
<your_ip>.qgsynthc Lists synthesis parameters to support incremental regeneration. ( Quartus® Prime Pro Edition only)
<your_ip>.qip

Contains all the required information about the IP component to integrate and compile the IP component in the Quartus Prime software.

<your_ip>.csv Contains information about the upgrade status of the IP component.

<your_ip>.bsf

A Block Symbol File (.bsf) representation of the IP variation for use in Quartus Prime Block Diagram Files (.bdf).

<your_ip>.spd

Required input file for ip-make-simscript to generate simulation scripts for supported simulators. The .spd file contains a list of files generated for simulation, along with information about memories that you can initialize.

<your_ip>.ppf The Pin Planner File (.ppf) stores the port and node assignments for IP components created for use with the Pin Planner.
<your_ip>_bb.v You can use the Verilog black-box (_bb.v) file as an empty module declaration for use as a black box.
<your_ip>.sip Contains information required for NativeLink simulation of IP components. You must add the .sip file to your Quartus® Prime project.
<your_ip>_inst.v and _inst.vhd HDL example instantiation template. You can copy and paste the contents of this file into your HDL file to instantiate the IP variation.
<your_ip>.regmap If IP contains register information, .regmap file generates. The .regmap file describes the register map information of master and slave interfaces. This file complements the .sopcinfo file by providing more detailed register information about the system. This enables register display views and user customizable statistics in the System Console.
<your_ip>.svd

Allows hard processor system (HPS) System Debug tools to view the register maps of peripherals connected to HPS within a Platform Designer system.

During synthesis, the .svd files for slave interfaces visible to System Console masters are stored in the .sof file in the debug section. System Console reads this section, which Platform Designer can query for register map information. For system slaves, Platform Designer can access the registers by name.

<your_ip>.v

and

<your_ip>.vhd 		HDL files that instantiate each submodule or child IP for synthesis or simulation.
mentor/

Contains a QuestaSim* script msim_setup.tcl to set up and run a simulation.

aldec/

Contains a Riviera-PRO* script rivierapro_setup.tcl to setup and run a simulation.

synopsys/vcs/

synopsys/vcsmx/

Contains a shell script vcs_setup.sh to set up and run a VCS* simulation.

Contains a shell script vcsmx_setup.sh and synopsys_ sim.setup file to set up and run a VCS* MX simulation.

submodules/ Contains HDL files for the IP submodule.
<child IP cores>/ For each generated child IP directory, Platform Designer generates synth/ andsim/ sub-directories.
Level Two Title