CPRI Intel® FPGA IP User Guide

Download PDF
ID 683595
Date 5/17/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the CPRI Intel® FPGA IP 2. Getting Started with the CPRI Intel® FPGA IP 3. CPRI IP Functional Description 4. CPRI Intel® FPGA IP Signals 5. CPRI Intel® FPGA IP Registers 6. CPRI Intel® FPGA IP User Guide Archives 7. Document Revision History for the CPRI Intel® FPGA IP User Guide
1. About the CPRI Intel® FPGA IP x
1.1. CPRI Intel® FPGA IP Core Supported Features 1.2. CPRI Intel® FPGA IP Device Family and Speed Grade Support 1.3. Intel® FPGA IP Verification 1.4. Resource Utilization for CPRI Intel® FPGA IP 1.5. CPRI IP Release Information
1.2. CPRI Intel® FPGA IP Device Family and Speed Grade Support x
1.2.1. CPRI IP Device Family Support 1.2.2. CPRI Intel® FPGA IP Device and Transceiver Speed Grade Support
2. Getting Started with the CPRI Intel® FPGA IP x
2.1. Installation and Licensing 2.2. Generating aCPRI Intel® FPGA IP 2.3. CPRI Intel® FPGA IP Generated Files 2.4. CPRI Intel® FPGA IP Parameters 2.5. Integrating the CPRI IP into your Design: Required External Blocks 2.6. Simulating Intel FPGA IP Cores 2.7. Running the CPRI IP Design Example 2.8. CPRI Design Example Clocks 2.9. About the Testbench 2.10. Compiling the Full Design and Programming the FPGA
2.1. Installation and Licensing x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating the CPRI IP into your Design: Required External Blocks x
2.5.1. Adding the Transceiver TX PLL IP Core 2.5.2. Adding the Reset Controller 2.5.3. Adding the Transceiver Reconfiguration Controller 2.5.4. Adding the Off-Chip Clean-Up PLL 2.5.5. Adding and Connecting the Single-Trip Delay Calibration Blocks 2.5.6. CPRI IP Transceiver PLL Calibration 2.5.7. Reference and System PLL Clock for your IP Design
2.5.7. Reference and System PLL Clock for your IP Design x
2.5.7.1. System PLL Connections for the Agilex® 7 F-tile Variations 2.5.7.2. System PLL Connections for the Agilex 5 Variations 2.5.7.3. Reset Sequencer Connections for the Agilex 5 Variations
3. CPRI IP Functional Description x
3.1. Interfaces Overview 3.2. CPRI Intel® FPGA IP Clocking Structure 3.3. CPRI Intel® FPGA IP Core Reset Requirements 3.4. Start-Up Sequence Following Reset 3.5. AUX Interface 3.6. Direct IQ Interface 3.7. Ctrl_AxC Interface 3.8. Direct Vendor Specific Access Interface 3.9. Real-Time Vendor Specific Interface 3.10. Direct HDLC Serial Interface 3.11. Direct L1 Control and Status Interface 3.12. L1 Debug Interface 3.13. Media Independent Interface (MII) to External Ethernet Block 3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block 3.15. CPU Interface to CPRI Intel® FPGA IP Registers 3.16. Auto-Rate Negotiation 3.17. Extended Delay Measurement 3.18. Deterministic Latency and Delay Measurement and Calibration 3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces 3.20. Testing Features
3.2. CPRI Intel® FPGA IP Clocking Structure x
3.2.1. Example CPRI Intel® FPGA IP Core Clock Connections in Different Clocking Modes
3.4. Start-Up Sequence Following Reset x
3.4.1. Start-Up Sequence Interface Signals
3.5. AUX Interface x
3.5.1. AUX Interface Signals 3.5.2. AUX Interface Synchronization 3.5.3. Auxiliary Latency Cycles 3.5.4. Direct Interface CPRI Frame Data Format
3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block x
3.14.1. GMII Normal Mode 3.14.2. Ethernet PCS Bypass Mode 3.14.3. Ethernet PCS Run-Time Switching
3.15. CPU Interface to CPRI Intel® FPGA IP Registers x
3.15.1. CPU Interface Signals 3.15.2. Accessing the Hyperframe Control Words
3.15.2. Accessing the Hyperframe Control Words x
3.15.2.1. Specifying the Control Word 3.15.2.2. Specifying the Position in the Control Word 3.15.2.3. Retrieving the Hyperframe Control Words 3.15.2.4. Writing the Hyperframe Control Words
3.17. Extended Delay Measurement x
3.17.1. Extended Delay Measurement for Soft Internal Buffers 3.17.2. Extended Delay Measurement for Stratix® 10 Hard FIFOs 3.17.3. Extended Delay Measurement Interface
3.18. Deterministic Latency and Delay Measurement and Calibration x
3.18.1. Delay Measurement and Calibration Features 3.18.2. Delay Requirements 3.18.3. Single-Hop Delay Measurement 3.18.4. Multi-Hop Delay Measurement 3.18.5. Delay Calibration Features
3.18.3. Single-Hop Delay Measurement x
3.18.3.1. Rx Path Delay 3.18.3.2. Tx Path Delay 3.18.3.3. Round-Trip Delay
3.18.5. Delay Calibration Features x
3.18.5.1. Single-Trip Delay Calibration 3.18.5.2. Round-Trip Delay Calibration 3.18.5.3. Tx Bitslip Delay
3.18.5.1. Single-Trip Delay Calibration x
3.18.5.1.1. Single-Trip Latency Measurement and Calibration Interface Signals
3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces x
3.19.1. CPRI Link 3.19.2. Main Transceiver Clock and Reset Signals 3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface 3.19.4. Arria® 10, Stratix® 10, and Agilex® 7 Transceiver Reconfiguration Interface 3.19.5. RS-FEC Interface 3.19.6. Interface to the External Reset Controller 3.19.7. Interface to the External PLL 3.19.8. Transceiver Debug Interface
3.20. Testing Features x
3.20.1. CPRI Intel® FPGA IP Core Loopback Modes 3.20.2. CPRI Intel® FPGA IP Core Self-Synchronization Feature
4. CPRI Intel® FPGA IP Signals x
4.1. CPRI Intel® FPGA IP Core L2 Interface 4.2. CPRI Intel® FPGA IP Core L1 Direct Access Interfaces 4.3. CPRI Intel® FPGA IP Core Management Interfaces 4.4. CPRI Intel® FPGA IP Core Transceiver and Transceiver Management Signals
1. About the CPRI Intel® FPGA IP
2. Getting Started with the CPRI Intel® FPGA IP
3. CPRI IP Functional Description
4. CPRI Intel® FPGA IP Signals
5. CPRI Intel® FPGA IP Registers
6. CPRI Intel® FPGA IP User Guide Archives
7. Document Revision History for the CPRI Intel® FPGA IP User Guide

3.6. Direct IQ Interface

If you turn on Enable direct IQ mapping interface in the CPRI parameter editor, the direct IQ interface is available. This interface allows direct access to the I/Q data time slots in the CPRI frame. You can connect this interface to any user-defined air standard I/Q mapping module.

This interface is Avalon-ST compliant with a ready latency value of 1.

You can alter the transmit latency with the Auxiliary and direct interfaces write latency cycle(s) parameter.

Table 25.  Direct IQ Interface SignalsAll interface signals are clocked by the cpri_clkout clock. The Data path width parameter determines the interface type and width, where N= 32 or 64, C= 3 or 7, and D= 31 or 63.
Direct IQ RX Interface

Signal Name

Direction

Description

iqN_rx_valid[C:0] Output Each asserted bit indicates the corresponding byte on the current iq_rx_data bus is valid I/Q data.
iqN_rx_data[D:0] Output I/Q data received from the CPRI frame. The iq_rx_valid signal indicates which bytes are valid I/Q data bytes.
Direct IQ TX Interface

Signal Name

Direction

Description

iqN_tx_ready[C:0] Output Each asserted bit indicates the IP core is ready to read I/Q data from the corresponding byte of iq_tx_data on the next clock cycle.
iqN_tx_valid[C:0] Input Write valid for iq_tx_data. Assert bit [n] to indicate that the corresponding byte on the current iq_tx_data bus is valid I/Q data.
iqN_tx_data[D:0] Input I/Q data to be written to the CPRI frame. The IP core writes the individual bytes of the current value on the iq_tx_data bus to the CPRI frame based on the iq_tx_ready signal from the previous cycle, and the iq_tx_valid signal in the current cycle.
Figure 38. Direct IQ RX Interface Timing DiagramDirect IQ RX interface behavior in a CPRI IP running at 0.6144 Gbps.

The aux_rx_x and aux_rx_seq signals are not part of this interface and are available only if you turn on the AUX interface in your CPRI IP core variation. However, their presence in the timing diagram explains the timing of the iq_rx_valid output signal that you use to identify the clock cycles with valid I/Q data.



Figure 39. Direct IQ TX Interface Timing DiagramExpected behavior on the direct IQ TX interface of a CPRI IP core running at 0.6144 Gbps.

The aux_tx_x and aux_tx_seq signals are not part of this interface and are available only if you turn on the AUX interface in your CPRI IP variation. However, their presence in the timing diagram explains the timing of the iq_tx_ready output signal that you use to identify the clock cycles when you can write I/Q data to the CPRI frame. Note that the write latency is two cpri_clkout clock cycles in this example.



Related Information
Level Two Title