May 2017 |
2017.05.31 |
Added support for Cyclone 10 LP and Cyclone 10 GX devices. |
May 2016 |
2016.05.02 |
- Added information about clkin maximum frequency should not exceed 20MHz or 25MHz.
- Added note to state that the read_dummyclk must be enabled when fast read option is used.
- Added information about allowing two clock cycles before sending a new signal after busy signal deasserted.
- Added note about .rpd files read and write sequence starts with the LSB.
|
December 2014 |
2014.12.15 |
- Added EPCQ-L devices.
- Added sce[] port and definition.
- Added die_erase parameter.
- Updated diagrams to reflect newly added port and parameter.
|
July 2014 |
2014.07.18 |
- Replaced MegaWizard Plug-In Manager information with IP Catalog.
- Added standard information about upgrading IP cores.
- Added standard installation and licensing information.
- Renamed ALTASMI_PARALLEL megafunction to Altera ASMI Parallel IP core.
|
December 2013 |
4.2 |
Updated the following sections to include ex4b_addr information:
- “Parameter Settings” on page 2–2.
- “Input Ports” on page 2–8.
- “ALTASMI_PARALLEL Block Diagram” on page 2–1.
- Added “4-byte Addressing Exit Operation for an EPCQ256 Device” on page 3–17.
|
May 2013 |
4.1 |
- Replaced the term dummy bytes with dummy cycles.
- Removed the Use ‘die_erase’ port parameter in Table 2–1 on page 2–2. This parameter is only available for selected customers.
- Updated the Use ‘read_address’ port parameter in Table 2–1 on page 2–2 to clarify that the width of the addr and read_address signals is 24 bit for other devices.
- Updated the caution statement in “About This Megafunction” on page 1–1.
|
December 2012 |
4.0 |
- Updated “Device Family Support” on page 1–3.
- Added “Enable 4-byte Addressing Operation for an EPCQ256 Device” on page 3–16, “EPCQ Devices Extended SPI Dual and Quad I/O Instruction” on page 3–9, and “EPCQ Devices Read Dummy Clock Instruction” on page 3–9.
- Updated Figure 2–1 on page 2–1 to include new ports.
- Updated the following sections to include EPCQ information:
“Read Memory Capacity ID from the EPCS/EPCQ Device” on page 3–2. “Fast Read Data from the EPCS/EPCQ Device” on page 3–7 “Read Data from the EPCS/EPCQ Device” on page 3–5 “Write Data to the EPCS/EPCQ Device” on page 3–10 “Erase Memory in a Specified Sector on the EPCS/EPCQ Device” on page 3–14 “Erase Memory in Bulk on the EPCS/EPCQ Device” on page 3–15 “Protect a Sector on the EPCS/EPCQ Device” on page 3–4 “Read Status Register of the EPCS/EPCQ Device” on page 3–13
- Updated Table 2–1 on page 2–3 to include new parameters.
- Updated Table 2–2 on page 2–10 to include en4b_addr and asmi_dataout ports information.
- Updated Table 2–3 on page 2–13 to include asmi_dclk, asmi_scein, asmi_sdoin and asmi_dataoe ports information.
- Change document to new user guide template.
|
September 2009 |
3.0 |
- Removed “Device Family Support”
- Added new information in “Introduction” on page 1
- Added “Parameter Settings” on page 17
- Added link to Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Datasheet
- Updated to include information about read_rdid signal
- Updated Figure 2 on page 3 to include Arria II GX and Stratix IV
- Added Figure 1 on page 2
- Removed “How to Contact Altera” and “Typographic Conventions” sections.
|
October 2007 |
2.4 |
- Updated for new MegaWizard™ Plug-In Manager pages
- Updated to include information about new fast_read command
|
May 2007 |
2.3 |
- Added ArriaTM GX to list of supported devices in “Device Family Support”
- Added Figure 1–2
- Updated Figures 1-2, 2-2, 2-3, 2-4, and 2-5
|
March 2007 |
2.2 |
- Removed Table 1-1 and added a list of supported devices.
- Updated for the Quartus II software version 7.0 by adding support for Cyclone®® III device.
|
December 2006 |
2.1 |
Updated device family support to include Stratix III. |
June 2006 |
2.0 |
- Updated all screen shots.
- Added the section “How to Use the Megafunction” on page 2-15.
|
November 2005 |
1.0 |
Initial release. |