Cyclone® V SoC Development Kit User Guide

Download PDF
ID 830285
Date 10/07/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Update Portal 5. Board Test System 6. Document Revision History for the Cyclone® V SoC Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents
2. Getting Started x
2.1. Before You Begin 2.2. Inspecting the Boards 2.3. Software and Driver Installation
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Standard Edition Software 2.3.2. Installing the Intel® SoC EDS 2.3.3. Installing the Development Kit 2.3.4. Installing the Intel® FPGA Download Cable II Driver
3. Development Kit Setup x
3.1. Setting Up the Development Kit 3.2. Factory Default Switch and Jumper Settings 3.3. Restoring the MAX® V CPLD to the Factory Setting 3.4. Restoring CFI Flash Device to the Factory Defaults
3.2. Factory Default Switch and Jumper Settings x
3.2.1. Restoring the Default Settings for Power Solution 2 Board 3.2.2. Restoring the Default Settings for Power Solution 1 Board
4. Board Update Portal x
4.1. Connecting to the Board Update Portal Web Page
5. Board Test System x
5.1. Preparing the Board for the Board Test System 5.2. Running the Board Test System 5.3. Using the Board Test System 5.4. The Power Monitor 5.5. The Clock Control 5.6. Configuring the FPGA Using the Quartus® Prime Programmer
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The System Info Tab 5.3.3. The GPIO Tab 5.3.4. The I2C Tab 5.3.5. The DDR3 Tab 5.3.6. The SDI Video Tab 5.3.7. The HSMC Tab
5.6. Configuring the FPGA Using the Quartus® Prime Programmer x
5.6.1. Before Configuring 5.6.2. Configuring the FPGA
A. Development Kit Components x
A.1. Board Overview A.2. Programming Flash Memory A.3. Power
A.2. Programming Flash Memory x
A.2.1. CFI Flash Memory A.2.2. quad SPI Flash Memory A.2.3. SD Card Memory
A.2.1. CFI Flash Memory x
A.2.1.1. CFI Flash Memory Map A.2.1.2. Programming CFI Flash Using the Quartus® Prime Programmer A.2.1.3. Converting .sof Files to a .pof
A.2.2. quad SPI Flash Memory x
A.2.2.1. Programming quad SPI Flash Using the Quartus® Prime Programmer
A.2.3. SD Card Memory x
A.2.3.1. Programming the SD Card Boot Image
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Update Portal
5. Board Test System
6. Document Revision History for the Cyclone® V SoC Development Kit User Guide
A. Development Kit Components
B. Additional Information

1.2. Feature Summary

Device

  • Cyclone® V SX SoC—5CSXFC6D6F31C6N (SoC)
  • MAX® V CPLD—5M2210ZF256C4N (system controller)
  • MAX® II CPLD—EPM570GF100 (embedded Intel® FPGA Download Cable II)

FPGA I/O Interfaces

  • 2 10/100 Megabit Ethernet PHYs (EtherCAT)
  • PCIe* 1.0 x4 female connector
  • Universal high-speed mezzanine card (HSMC)—x4 transceivers, x16 TX LVDS, x16 RX LVDS
  • 1 serial digital interface (SDI) channel
  • 4 SMAs for one transceiver channel
  • 4 push buttons
  • 2 switches
  • 4 LEDs

HPS I/O Interfaces

  • 1 USB 2.0 On-the-Go (OTG)
  • 1 10/100/1000 Megabit Ethernet (10MbE/100MbE/1000MbE)
  • 1 CAN
  • 1 UART (UART to USB bridge)
  • 1 real-time clock (with battery backup)
  • 1 two-line text LCD
  • 1-/2-channel, 20 bit delta-sigma analog-to-digital converter (Linear Technology LTC2422)
  • 4 push buttons
  • 4 switches
  • 4 LEDs

HPS Boot Sources

  • 1 GB DDR3 SDRAM (32 bit) with error correction code (ECC)
  • 128 MB quad SPI flash memory
  • Micro-SD card socket with 4 GB micro-SD card flash device

Memory

  • HPS I/O Memory:
    • 1 GB DDR3 SDRAM (32 bit) with error correction code (ECC)
    • 128 MB quad SPI flash memory
    • Micro-SD card socket with 4 GB micro-SD card flash device
  • FPGA Memory:
    • 1 GB DDR3 SDRAM (32 bit)

Cables and Adapters

  • Power Solution 2 board—12 V AC adapter, PCIe* edge connector
  • Power Solution 1 board—Laptop DC Input 14 – 20 V adapter, PCIe* edge connector

Software

A one-year license for the Quartus® Prime Pro Edition design software is included with the purchase of the kit. Refer to the Intel® FPGA Software Installation and Licensing for more information.

Related Information
Level Two Title