Hard Processor System Booting User Guide: Agilex™ 5 SoCs

Download PDF
ID 813762
Date 8/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. FPGA Configuration First Mode 3. HPS Boot First Mode 4. Creating the Configuration Files 5. HPS Boot Flows 6. Configuring the FPGA Fabric from HPS Software 7. Debugging the Agilex™ 5 SoC FPGA Boot Flow 8. Document Revision History for the Hard Processor System Booting User Guide: Agilex™ 5 SoCs
1. Introduction x
1.1. Glossary 1.2. Agilex™ 5 SoC FPGA Boot Overview
2. FPGA Configuration First Mode x
2.1. Boot Flow Overview for FPGA Configuration First Mode 2.2. System Layout for FPGA Configuration First Mode
2.1. Boot Flow Overview for FPGA Configuration First Mode x
2.1.1. Power-On Reset (POR) 2.1.2. Secure Device Manager 2.1.3. First-Stage Bootloader 2.1.4. Second-Stage Bootloader 2.1.5. Operating System 2.1.6. Application
2.2. System Layout for FPGA Configuration First Mode x
2.2.1. External Configuration Host Only 2.2.2. External Configuration Host with HPS Flash 2.2.3. Single SDM Flash 2.2.4. FPGA Configuration First - Dual Flash System
3. HPS Boot First Mode x
3.1. Boot Flow Overview 3.2. System Layout for HPS Boot First Mode
3.1. Boot Flow Overview x
3.1.1. Power-On Reset (POR) 3.1.2. Secure Device Manager 3.1.3. First-Stage Bootloader 3.1.4. Second-Stage Bootloader 3.1.5. Operating System 3.1.6. Application
3.2. System Layout for HPS Boot First Mode x
3.2.1. External Configuration Host Only 3.2.2. External Configuration Host with HPS Flash 3.2.3. Single SDM Flash 3.2.4. HPS Boot First - Dual Flash System
4. Creating the Configuration Files x
4.1. Overview 4.2. Quartus® Prime Hardware Project Compilation 4.3. Bootloader Software Compilation 4.4. Programming File Generator 4.5. Configuration over JTAG 4.6. Configuration from QSPI 4.7. Configuration over AVST 4.8. Configuration via Protocol 4.9. Remote System Update 4.10. Partial Reconfiguration
4.2. Quartus® Prime Hardware Project Compilation x
4.2.1. Device and Pin Options 4.2.2. Platform Designer Options 4.2.3. Generation of Debug HPS FSBL from Hardware Design Build
4.5. Configuration over JTAG x
4.5.1. FPGA Configuration First 4.5.2. HPS Boots First
4.6. Configuration from QSPI x
4.6.1. Supported QSPI Devices 4.6.2. FPGA Configuration First 4.6.3. HPS Boot First
4.6.2. FPGA Configuration First x
4.6.2.1. Creating Configuration Files from Command Line 4.6.2.2. Creating Configuration Files Using Graphical Interface
4.6.3. HPS Boot First x
4.6.3.1. Creating Configuration Files from Command Line 4.6.3.2. Creating Configuration Files Using Graphical Interface
4.7. Configuration over AVST x
4.7.1. FPGA Configuration First 4.7.2. HPS Boot First
4.7.1. FPGA Configuration First x
4.7.1.1. Creating Configuration Files from Command Line 4.7.1.2. Creating Configuration Files Using Graphical Interface
4.7.2. HPS Boot First x
4.7.2.1. Creating Configuration Files from Command Line 4.7.2.2. Creating Configuration Files Using Graphical Interface
4.8. Configuration via Protocol x
4.8.1. Creating Configuration Files from Command Line 4.8.2. Creating Configuration Files Using Graphical Interface
5. HPS Boot Flows x
5.1. U-Boot ATF Linux* Boot 5.2. ATF Linux Boot 5.3. ATF Zephyr* Boot
6. Configuring the FPGA Fabric from HPS Software x
6.1. Configuring the FPGA Fabric from U-Boot 6.2. Configuring the FPGA Fabric from Linux* 6.3. FPGA Partial Reconfiguration from Linux*
7. Debugging the Agilex™ 5 SoC FPGA Boot Flow x
7.1. Reset 7.2. Debugging the HPS Bootloader Using the Arm* Development Studio for Intel® SoC FPGA (Arm* DS for Intel® SoC FPGA) Edition
7.1. Reset x
7.1.1. HPS Reset Pin 7.1.2. L4 Watchdog Timer 0
1. Introduction
2. FPGA Configuration First Mode
3. HPS Boot First Mode
4. Creating the Configuration Files
5. HPS Boot Flows
6. Configuring the FPGA Fabric from HPS Software
7. Debugging the Agilex™ 5 SoC FPGA Boot Flow
8. Document Revision History for the Hard Processor System Booting User Guide: Agilex™ 5 SoCs

4.8.1. Creating Configuration Files from Command Line

The following example creates the configuration files for CvP:

quartus_pfg -c design.sof design.jic design.rpd design.map \
-o hps_path=fsbl.hex \
-o device=MT25QU128 \
-o flash_loader=A5ED065BB32AR0 \
-o mode=ASX4 \
-o bitswap=on \
-o cvp=on

The input and output files for this command are:

  • Input Files:
    • design.sof
    • fsbl.hex
  • Output Files:
    • design.periph.jic
    • design.core.rbf
    • design.rpd (optional)
    • design.map (optional)

The command parameters are listed below:

Table 15.  Command Parameters
Parameter Description
hps_path Location of HPS FSBL file in hex format
device Target QSPI device. Use a device listed in Supported QSPI Devices or use the graphical interface to determine available options.
flash_loader

The helper image to be used for writing JIC to QSPI Flash. It is typically an alphanumeric prefix of your FPGA part number.

You may use the graphical interface mode to determine available options.
mode AS x4 for QSPI
bitswap Set to "on" to create RPD with plain binary format, usable by 3rd party tools.
cvp Set to "on" to enable Configuration via Protocol.
Note: When using HPS boot first your JIC is small, and you can target a QSPI device that is smaller than what you have on board. When programming the resulted JIC file, a warning is displayed, but the resulted file size and erasing and programming times are reduced accordingly.
Level Two Title