Intel Agilex® 7 FPGA I-Series Transceiver (6 × F-Tile) Development Kit User Guide

Download PDF
ID 776646
Date 5/31/2023
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Power Up the Development Kit 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Revision History A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Intel® Quartus® Prime Software and Driver Installation 2.2. Quick Start Guide 2.3. Design Examples
3. Power Up the Development Kit x
3.1. Default Settings 3.2. Power Up 3.3. Perform Board Restore
3.3. Perform Board Restore x
3.3.1. Restore board System Intel® MAX® 10 with default factory image 3.3.2. Restore Board QSPI Flash with the Default Factory Image
4. Board Test System x
4.1. Set Up BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control On-Board Clock through Clock Controller GUI 4.4. Monitor On-Board Power Regulator through Power Monitor GUI 4.5. Identify Test Pass or Fail-based on BTS GUI Test Status
4.1. Set Up BTS GUI Running Environment x
4.1.1. Download OpenJDK 4.1.2. Download OpenJFX 4.1.3. Install OpenJDK and OpenJFX 4.1.4. Install Intel® Quartus® Prime Software 4.1.5. Run BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Info Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. The XCVR Tab 4.2.6. The Memory Tab
4.2.5. The XCVR Tab x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The FMCA NRZ Tab 4.2.5.3. The FMCB NRZ Tab 4.2.5.4. The QSFPDD400 PAM4 Tab 4.2.5.5. The QSFP NRZ Tab 4.2.5.6. The SFP Tab 4.2.5.7. The OSFP Tab
5. Development Kit Hardware and Configuration x
5.1. Configure the FPGA Device by Active Serial (AS) Modes (Default Mode) 5.2. Configure the FPGA Device by Avalon® -ST (AvST) Modes
6. Custom Projects for the Development Kit x
6.1. Add SmartVID Settings in the Intel® Quartus® Prime QSF File 6.2. Golden Top
A. Development Kit Components x
A.1. Board Overview and Components A.2. System Management A.3. Power A.4. Clocks A.5. General Input/Output A.6. Memory Interfaces A.7. Communication Interfaces A.8. Daughter Cards
A.1. Board Overview and Components x
A.1.1. Board Overview A.1.2. Board Components
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Power Up the Development Kit
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Revision History
A. Development Kit Components
B. Additional Information

3. Power Up the Development Kit

The instructions in this chapter explain how to setup the Intel Agilex® 7 FPGA I-Series Transceiver Development Kit for specific use cases.


Section Content
Default Settings
Power Up
Perform Board Restore

Level Two Title