AN 957: Time-Sensitive Networking for Drive-on-Chip Design Example

Download PDF
ID 683707
Date 10/30/2021
Public
Document Table of Contents
Document Table of Contents x
1. About the Time-Sensitive Networking for Drive-on-Chip Design Example 2. Getting Started with the TSN for Drive-on-Chip Design Example 3. Porting the Intel MAX 10 Drive-On-Chip design to the Cyclone V SoC Development Board 4. Running HPS Software for the TSN Drive-on-Chip Design 5. Connecting the Cyclone V SoC Development board to the Tandem 48 V Motion-Power board 6. Running the Program 7. TSN Configuration Example 8. Document Revision History for AN 957: Time-Sensitive Networking for Drive-on-Chip Design Example A. Example .qsf for Pin Assignments and Attributes B. Top-level Verilog HDL File Example C. YOCTO Build Patch File (cvsx_doc_tsn_2_3-rt) for the TSN Drive-on-Chip Design Example D. Script to read and change MAC addresses from Cyclone V SoC EEPROM
1. About the Time-Sensitive Networking for Drive-on-Chip Design Example x
1.1. Features of TSN for Drive-on-Chip Design Example 1.2. TSN for Drive-on-Chip Design Example General Description 1.3. Messages from the TSN Drive-on-Chip Design Example 1.4. Design Flow for the TSN Drive-on-Chip Design Example
2. Getting Started with the TSN for Drive-on-Chip Design Example x
2.1. Hardware Requirements for the TSN for Drive-on-Chip Design Example 2.2. Software Requirements for the TSN for Drive-on-Chip Design Example 2.3. Configuring the Cyclone V SoC Development Board for the TSN for Drive-on-Chip Design Example 2.4. Programming the FPGA for the TSN for Drive-on-Chip Design Example 2.5. Creating an SD Card Image for the TSN for Drive-on-Chip Design Example 2.6. Turning on the Cyclone V SoC Development Board for the TSN for Drive-on-Chip Design Example 2.7. Configuring the TSN IP
3. Porting the Intel MAX 10 Drive-On-Chip design to the Cyclone V SoC Development Board x
3.1. Changing File Names, Revision Name, and Target Device for the TSN Drive-on-Chip Design Example 3.2. Modifying the Drive-On-Chip Qsys System 3.3. Adding the TTTech TSN IP to the Qsys system 3.4. Connecting the TSN and Drive-on-Chip Subsystems 3.5. Compiling the Quartus Prime Design and Top-Level Module 3.6. Generating the Preloader 3.7. Generating a .jic file 3.8. Compiling the Drive-on-Chip Design Software in Nios II Software Build Tools 3.9. Launching a YOCTO Build 3.10. Building an SD Card Image for the TSN Drive-on-Chip Design Example 3.11. Changing MAC Addresses 3.12. Reading and Checking Physical Addresses on the Cyclone V SoC Development Board
4. Running HPS Software for the TSN Drive-on-Chip Design x
4.1. Installing the Arm Compiler for Motor Control from Linux 4.2. Creating a Basic C Program for Motor Control 4.3. OPC UA PubSub based on open62541 4.4. Getting and Building open62541 4.5. Setting up Debug Sessions in DS-5
1. About the Time-Sensitive Networking for Drive-on-Chip Design Example
2. Getting Started with the TSN for Drive-on-Chip Design Example
3. Porting the Intel MAX 10 Drive-On-Chip design to the Cyclone V SoC Development Board
4. Running HPS Software for the TSN Drive-on-Chip Design
5. Connecting the Cyclone V SoC Development board to the Tandem 48 V Motion-Power board
6. Running the Program
7. TSN Configuration Example
8. Document Revision History for AN 957: Time-Sensitive Networking for Drive-on-Chip Design Example
A. Example .qsf for Pin Assignments and Attributes
B. Top-level Verilog HDL File Example
C. YOCTO Build Patch File (cvsx_doc_tsn_2_3-rt) for the TSN Drive-on-Chip Design Example
D. Script to read and change MAC addresses from Cyclone V SoC EEPROM

3.11. Changing MAC Addresses

The TTTech TSN IP works with MAC addresses for the network interfaces. For the Cyclone V SoC Development Board, the EEPROM configuration stores these addresses. When the complete systems boots, it takes the addresses from this EEPROM and assigns them to different interfaces as described in the ttt-ip-init.sh file.
  1. Type the i2c command after the Cyclone V SoC Development board boots. For example:
    >> i2cset -y 0 0x51 0 56 0xac i
  2. Check your changes by typing the following command:
    >> i2cset -y 0 0x51 0 56 i
    >> i2cget -y 0 0x51
When your change the MAC addresses in the EEPROM, they remain after switching off the Development board. Intel recommends you reboot the Development board and use a fresh SD card image as some of the previously undesired addresses might copy into the system configuration.
Level Two Title