Visible to Intel only — GUID: nik1409872218471
Ixiasoft
1. Transceiver Architecture in Arria V Devices
2. Transceiver Clocking in Arria V Devices
3. Transceiver Reset Control in Arria V Devices
4. Transceiver Protocol Configurations in Arria V Devices
5. Transceiver Custom Configurations in Arria V Devices
6. Transceiver Configurations in Arria V GZ Devices
7. Transceiver Loopback Support in Arria V Devices
8. Dynamic Reconfiguration in Arria V Devices
1.2.2.1.1. Word Aligner in Manual Alignment Mode
1.2.2.1.2. Bit-Slip Mode
1.2.2.1.3. Word Aligner in Automatic Synchronization State Machine Mode
1.2.2.1.4. Word Aligner in Deterministic Latency State Machine Mode
1.2.2.1.5. Programmable Run-Length Violation Detection
1.2.2.1.6. Receiver Polarity Inversion
1.2.2.1.7. Bit Reversal
1.2.2.1.8. Receiver Byte Reversal
1.2.3.2.1. Receiver Gearbox
1.2.3.2.2. Block Synchronizer
1.2.3.2.3. Disparity Checker
1.2.3.2.4. Descrambler
Frame Synchronous Mode
Self Synchronous Mode
1.2.3.2.5. Frame Synchronizer
1.2.3.2.6. Bit-Error Rate (BER) Monitor
1.2.3.2.7. 64B/66B Decoder
1.2.3.2.8. CRC-32 Checker
1.2.3.2.9. Receiver FIFO
3.1. PHY IP Embedded Reset Controller
3.2. User-Coded Reset Controller
3.3. Transceiver Reset Using Avalon Memory Map Registers
3.4. Clock Data Recovery in Manual Lock Mode
Resetting the Transceiver During Dynamic Reconfiguration
3.6. Transceiver Blocks Affected by the Reset and Powerdown Signals
3.7. Transceiver Power-Down
3.8. Document Revision History
3.2.1. User-Coded Reset Controller Signals
3.2.2. Resetting the Transmitter with the User-Coded Reset Controller During Device Power-Up
3.2.3. Resetting the Transmitter with the User-Coded Reset Controller During Device Operation
3.2.4. Resetting the Receiver with the User-Coded Reset Controller During Device Power-Up Configuration
3.2.5. Resetting the Receiver with the User-Coded Reset Controller During Device Operation
4.1. PCI Express
4.2. Gigabit Ethernet
4.3. XAUI
4.4. 10GBASE-R
4.5. Serial Digital Interface
4.6. Gigabit-Capable Passive Optical Network (GPON)
4.7. Serial Data Converter (SDC) JESD204
4.8. SATA and SAS Protocols
4.9. Deterministic Latency Protocols—CPRI and OBSAI
4.10. Serial RapidIO
4.11. Document Revision History
4.1.2.1. PIPE Interface
4.1.2.2. Transmitter Electrical Idle Generation
4.1.2.3. Power State Management
4.1.2.4. 8B/10B Encoder Usage for Compliance Pattern Transmission Support
4.1.2.5. Receiver Status
4.1.2.6. Receiver Detection
4.1.2.7. Clock Rate Compensation Up to ±300 ppm
4.1.2.8. PCIe Reverse Parallel Loopback
6.1.1. 10GBASE-R and 10GBASE-KR Transceiver Datapath Configuration
6.1.2. 10GBASE-R and 10GBASE-KR Supported Features
6.1.3. 1000BASE-X and 1000BASE-KX Transceiver Datapath
6.1.4. 1000BASE-X and 1000BASE-KX Supported Features
6.1.5. Synchronization State Machine Parameters in 1000BASE-X and 1000BASE-KX Configurations
6.1.6. Transceiver Clocking in 10GBASE-R, 10GBASE-KR, 1000BASE-X, and 1000BASE-KX Configurations
6.3.1. Transceiver Datapath Configuration
6.3.2. Supported Features for PCIe Configurations
6.3.3. Supported Features for PCIe Gen3
6.3.4. Transceiver Clocking and Channel Placement Guidelines
6.3.5. Advanced Channel Placement Guidelines for PIPE Configurations
6.3.6. Transceiver Clocking for PCIe Gen3
6.7.1. Protocols and Transceiver PHY IP Support
6.7.2. Native PHY Transceiver Datapath Configuration
6.7.3. Standard PCS Features
6.7.4. 10G PCS Supported Features
6.7.5. 10G Datapath Configurations with Native PHY IP
6.7.6. PMA Direct Supported Features
6.7.7. Channel and PCS Datapath Dynamic Switching Reconfiguration
8.1. Dynamic Reconfiguration Features
8.2. Offset Cancellation
8.3. Transmitter Duty Cycle Distortion Calibration
8.4. PMA Analog Controls Reconfiguration
8.5. Dynamic Reconfiguration of Loopback Modes
8.6. Transceiver PLL Reconfiguration
8.7. Transceiver Channel Reconfiguration
8.8. Transceiver Interface Reconfiguration
8.9. Reduced .mif Reconfiguration
8.10. On-Chip Signal Quality Monitoring (Eye Viewer)
8.11. Adaptive Equalization
8.12. Decision Feedback Equalization
8.13. Unsupported Reconfiguration Modes
8.14. Document Revision History
Visible to Intel only — GUID: nik1409872218471
Ixiasoft
1.2.3.2.4. Descrambler
The descrambler descrambles data per the protocol specifications supported by the 10G PCS. The descrambler operates either in frame synchronous or self synchronous mode.
Frame Synchronous Mode
Frame synchronous mode is used in Interlaken configurations only. When block synchronization is achieved, the descrambler uses the scrambler seed from the received scrambler state word. This block also forwards the current descrambler state to the frame synchronizer.
Self Synchronous Mode
Self synchronous mode is used in 10GBASE-R configurations only.