Intel® Arria® 10 SoC Development Kit User Guide

Download PDF
ID 683227
Date 2/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Intel® Arria® 10 SoC Development Kit Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Board Components 6. Document Revision History for the Intel® Arria® 10 SoC Development Kit User Guide A. Additional Information
1. Intel® Arria® 10 SoC Development Kit Overview x
1.1. General Description 1.2. Board Component Blocks 1.3. Recommended Operating Conditions 1.4. Handling the Board
2. Getting Started x
2.1. Board Inspection 2.2. Installing the Subscription Edition of the Intel® Quartus® Prime Design Software 2.3. Installing the Intel® SoC Embedded Development Suite (EDS) 2.4. Development Kit Installer 2.5. Installing the Intel® FPGA Download Cable Driver 2.6. SD Card Image with Example Software
2.2. Installing the Subscription Edition of the Intel® Quartus® Prime Design Software x
2.2.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Board 3.2. Default Switch and Jumper Settings
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Version Selector 4.4. Using the Board Test System
4.4. Using the Board Test System x
4.4.1. Using the Configure Menu 4.4.2. The System Info Tab 4.4.3. The GPIO Tab 4.4.4. The XCVR Tab Status Port PMA Setting Data Type Error Control Run Control 4.4.5. The PCIe* Tab 4.4.6. The FMCA Tab 4.4.7. The FMCB Tab 4.4.8. The DDR3 Tab 4.4.9. The DDR4 Tab 4.4.10. The EEPROM Tab 4.4.11. The Power Monitor 4.4.12. The Clock Control
5. Board Components x
5.1. Board Overview 5.2. Featured Device: Intel® Arria® 10 SoC 5.3. MAX V CPLD 5M2210 System Controller 5.4. Configuration 5.5. Status Elements 5.6. Setup Elements 5.7. General User Input/Output 5.8. Clock Circuitry 5.9. Components and Interfaces 5.10. Memory 5.11. Board Power Supply
5.4. Configuration x
5.4.1. System Controller Configuration 5.4.2. FPGA and I/O MUX CPLD Programming over On-Board Intel® FPGA Download Cable II 5.4.3. FPGA Programming by HPS 5.4.4. FPGA Programming by EPCQ Device 5.4.5. FPGA Programming over External Intel® FPGA Download Cable
5.6. Setup Elements x
5.6.1. Board Settings DIP Switch 5.6.2. JTAG Chain Control DIP Switch 5.6.3. Reference Clock Source Selection 5.6.4. CPU Reset Push Button 5.6.5. Logic Reset Push Button
5.7. General User Input/Output x
5.7.1. Character LCD
5.8. Clock Circuitry x
5.8.1. On-Board Oscillators
5.9. Components and Interfaces x
5.9.1. PCIe 5.9.2. 10/100/1000 Ethernet (HPS) 5.9.3. 10/100/1000 Ethernet (FPGA) 5.9.4. FMC 5.9.5. HPS Shared I/O 5.9.6. USB 2.0 Port (HPS) 5.9.7. RS-232 UART (HPS) 5.9.8. Real-Time Clock (HPS) 5.9.9. SFP+ 5.9.10. I2C Interface 5.9.11. FPGA General I/O Configuration 5.9.12. HPS SPIO Interface
5.9.11. FPGA General I/O Configuration x
5.9.11.1. FPGA-I/O MAX V Interface 5.9.11.2. LMK04828 Controller 5.9.11.3. FPGA Resistor MUX 5.9.11.4. FPGA Debug Port 5.9.11.5. FPGA PMBUS VID 5.9.11.6. FPGA Auxiliary Signals
5.10. Memory x
5.10.1. FPGA External Memory 5.10.2. HPS External Memory 5.10.3. HPS Boot Flash Interface 5.10.4. I2C EEPROM 5.10.5. Daughtercards
5.11. Board Power Supply x
5.11.1. Power Distribution System 5.11.2. Power Measurement
A. Additional Information x
A.1. Compliance and Conformity Statements
A.1. Compliance and Conformity Statements x
A.1.1. CE EMI Conformity Caution
1. Intel® Arria® 10 SoC Development Kit Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Board Components
6. Document Revision History for the Intel® Arria® 10 SoC Development Kit User Guide
A. Additional Information

4.4.4. The XCVR Tab

This tab allows you to perform loopback tests on the QSFP, SFP, SMA, and SDI ports.
Figure 13. The XCVR Tab

Status

Displays the following status information during a loopback test:
  • PLL lock: Shows the PLL locked or unlocked state.
  • Pattern sync: Shows the pattern synced or not synced state. The pattern is considered synced when the start of the data sequence is detected.
  • Details: Shows the PLL lock and pattern sync status, and detected errors of each channels.
Figure 14. XCVR Tab: PLL and Pattern Status

Port

Allows you to specify which interface to test. The following port tests are available:
  • SFP A x1
  • SFP B x1
  • SMA x1
  • SDI

PMA Setting

Allows you to make changes to the PMA parameters that affect the active transceiver interface. The following settings are available for analysis:
  • Serial Loopback: Routes signals between the transmitter and the receiver.
  • VOD: Specifies the voltage output differential of the transmitter buffer.
  • Pre-emphasis tap:
    • 1st pre: Specifies the amount of pre-emphasis on the pre-tap of the transmitter buffer.
    • 2nd pre: Specifies the amount of pre-emphasis on the second pre-tap of the transmitter buffer.
    • 1st post: Specifies the amount of pre-emphasis on the first post tap of the transmitter buffer.
    • 2nd post: Specifies the amount of pre-emphasis on the second post tap of the transmitter buffer.
  • Equalizer: Specifies the AC gain setting for the receiver equalizer in four stage mode.
  • DC gain: Specifies the DC gain setting for the receiver equalizer in four stage mode.
  • VGA: Specifies the VGA gain value.
Figure 15. XCVR Tab: Set PMA Values

Data Type

Specifies the type of data contained in the transactions. The following data types are available for analysis:
  • PRBS 7: Selects pseudo-random 7-bit sequences.
  • PRBS 15: Selects pseudo-random 15-bit sequences.
  • PRBS 23: Selects pseudo-random 23-bit sequences.
  • PRBS 31: Selects pseudo-random 31-bit sequences.
  • HF: Selects highest frequency divide-by-2 data pattern 10101010.
  • LF: Selects lowest frequency divide-by-33 data pattern.

Error Control

Displays data errors detected during analysis and allows you to insert errors:
  • Detected errors: Displays the number of data errors detected in the hardware.
  • Inserted errors: Displays the number of errors inserted into the transmit data stream.
  • Insert Error: Inserts a one-word error into the transmit data stream each time you click the button. Insert Error is only enabled during transaction performance analysis.
  • Clear: Resets the Detected errors and Inserted errors counters to zeroes.

Run Control

  • Start: Initiates the selected ports transaction performance analysis.
    Note: Always click Clear before Start.
  • Stop: Terminates transaction performance analysis.
  • TX and RX performance bars: Show the percentage of maximum theoretical data rate that the requested transactions are able to achieve.
Level Two Title