Clocking and PLL User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813671
Date 10/07/2024
Public
Document Table of Contents
Document Table of Contents x
1. Agilex™ 5 Clocking and PLL Overview 2. Agilex™ 5 Clocking and PLL Architecture and Features 3. Agilex™ 5 Clocking and PLL Design Considerations 4. Clock Control Intel® FPGA IP Core 5. IOPLL Intel® FPGA IP Core 6. I/O PLL Reconfiguration 7. Document Revision History for the Clocking and PLL User Guide: Agilex™ 5 FPGAs and SoCs
1. Agilex™ 5 Clocking and PLL Overview x
1.1. Clock Networks Overview 1.2. PLLs Overview
2. Agilex™ 5 Clocking and PLL Architecture and Features x
2.1. Clock Networks Architecture and Features 2.2. PLLs Architecture and Features
2.1. Clock Networks Architecture and Features x
2.1.1. Clock Network Architecture 2.1.2. Clock Resources 2.1.3. Clock Control Features
2.1.1. Clock Network Architecture x
2.1.1.1. Clock Network Hierarchy 2.1.1.2. Clock Sectors 2.1.1.3. Programmable Clock Routing
2.1.3. Clock Control Features x
2.1.3.1. Clock Gating 2.1.3.2. Clock Divider
2.1.3.1. Clock Gating x
2.1.3.1.1. Root Clock Gate 2.1.3.1.2. Sector Clock Gate 2.1.3.1.3. I/O PLL Clock Gate 2.1.3.1.4. LAB Clock Gate
2.2. PLLs Architecture and Features x
2.2.1. PLL Features 2.2.2. PLL Usage 2.2.3. PLL Locations 2.2.4. PLL Architecture 2.2.5. PLL Control Signals 2.2.6. PLL Feedback Modes 2.2.7. Clock Multiplication and Division 2.2.8. Programmable Phase Shift 2.2.9. Programmable Duty Cycle 2.2.10. PLL Cascading 2.2.11. PLL Input Clock Switchover 2.2.12. PLL Reconfiguration and Dynamic Phase Shift 2.2.13. PLL Calibration
2.2.5. PLL Control Signals x
2.2.5.1. Reset 2.2.5.2. Locked
2.2.6. PLL Feedback Modes x
2.2.6.1. Direct Compensation Mode 2.2.6.2. LVDS Compensation Mode 2.2.6.3. Source Synchronous Compensation Mode 2.2.6.4. Normal Compensation Mode 2.2.6.5. Zero-Delay Buffer Mode 2.2.6.6. External Feedback Mode
2.2.11. PLL Input Clock Switchover x
2.2.11.1. Automatic Switchover 2.2.11.2. Automatic Switchover with Manual Override 2.2.11.3. Manual Clock Switchover
2.2.13. PLL Calibration x
2.2.13.1. Power-Up Calibration 2.2.13.2. User Calibration 2.2.13.3. Static Phase Error Calibration
3. Agilex™ 5 Clocking and PLL Design Considerations x
3.1. Guidelines: Clock Switchover 3.2. Guidelines: Timing Closure 3.3. Guidelines: Resetting the PLL 3.4. Guidelines: Configuration Constraints 3.5. Clocking Constraints 3.6. IP Core Constraints 3.7. Guideline: Achieving 5% Duty Cycle for fOUT_EXT ≥ 300 MHz Using tx_outclk Port from LVDS SERDES Intel® FPGA IP
4. Clock Control Intel® FPGA IP Core x
4.1. Release Information for Clock Control Intel® FPGA IP 4.2. Clock Control IP Core Parameters 4.3. Clock Control IP Core Ports and Signals
5. IOPLL Intel® FPGA IP Core x
5.1. Release Information for IOPLL Intel® FPGA IP Core 5.2. IOPLL IP Core Parameters 5.3. IOPLL IP Core Ports and Signals
5.2. IOPLL IP Core Parameters x
5.2.1. IOPLL IP Core Parameters - PLL Tab 5.2.2. IOPLL IP Core Parameters - Settings Tab 5.2.3. IOPLL IP Core Parameters - Cascading Tab 5.2.4. IOPLL IP Core Parameters - Advanced Parameters Tab
6. I/O PLL Reconfiguration x
6.1. Release Information for EMIF Calibration IP 6.2. Implementing HSIO I/O PLL Reconfiguration using EMIF Calibration IP 6.3. Implementing HVIO I/O PLL Reconfiguration 6.4. Reconfiguration Guideline for I/O PLLs 6.5. Axilite Interface Ports in the EMIF Calibration IP 6.6. Address Bus and Data Bus Settings 6.7. Design Example
6.2. Implementing HSIO I/O PLL Reconfiguration using EMIF Calibration IP x
6.2.1. Setting Up the IOPLL Intel® FPGA IP 6.2.2. Setting Up the EMIF Calibration IP 6.2.3. Connectivity Between IOPLL and EMIF Calibration IP
6.3. Implementing HVIO I/O PLL Reconfiguration x
6.3.1. Setting Up the IOPLL Intel® FPGA IP 6.3.2. Read and Write Operations
6.4. Reconfiguration Guideline for I/O PLLs x
6.4.1. Enabling Reconfiguration for The Desired I/O PLL 6.4.2. Clearing off Calibration Statuses 6.4.3. Reconfiguring The I/O PLL 6.4.4. Recalibration of I/O PLL 6.4.5. Clock Gating (Optional)
6.6. Address Bus and Data Bus Settings x
6.6.1. Divide Settings and the Corresponding Data Bit Setting for Reconfiguration 6.6.2. Data Bus Setting for Clock Gating Reconfiguration 6.6.3. Data Bus Setting For Charge Pump Current
6.7. Design Example x
6.7.1. Reconfiguration Option: Reconfiguration Through EMIF Calibration IP 6.7.2. Reconfiguration Option: Reconfiguration Through HVIO Interfaces 6.7.3. Reconfiguration Option: Clock Gating Reconfiguration
1. Agilex™ 5 Clocking and PLL Overview
2. Agilex™ 5 Clocking and PLL Architecture and Features
3. Agilex™ 5 Clocking and PLL Design Considerations
4. Clock Control Intel® FPGA IP Core
5. IOPLL Intel® FPGA IP Core
6. I/O PLL Reconfiguration
7. Document Revision History for the Clocking and PLL User Guide: Agilex™ 5 FPGAs and SoCs

2.2.11.2. Automatic Switchover with Manual Override

In automatic switchover with manual override mode, you can use the extswitch signal for user- or system-controlled switch conditions. You can use this mode for same-frequency switchover, or to switch between inputs of different frequencies.

For example, if inclk0 is 66 MHz and inclk1 is 200 MHz, you must control switchover using the extswitch signal. The automatic clock-sense circuitry cannot monitor clock input (inclk0 and inclk1) frequencies with a frequency difference of more than 100% (2×).

This feature is useful when the clock sources originate from multiple cards on the backplane, requiring a system-controlled switchover between the frequencies of operation.

You must choose the backup clock frequency and set the M, N, and C counters so that the VCO operates within the recommended operating frequency range. The Quartus® Prime software notifies you if a given combination of inclk0 and inclk1 frequencies cannot meet this requirement.

Figure 22. Clock Switchover Using the extswitch (Manual) ControlThis figure shows a clock switchover waveform controlled by the extswitch signal. In this case, both clock sources are functional and inclk0 is selected as the reference clock. The switchover sequence starts when the extswitch signal goes low. On the falling edge of inclk0, the counter’s reference clock, muxout, is gated off to prevent clock glitching. On the falling edge of inclk1, the reference clock multiplexer switches from inclk0 to inclk1 as the I/O PLL reference. The activeclock signal changes to indicate the clock which is currently feeding the I/O PLL.


In automatic override with manual switchover mode, the activeclock signal inverts after the extswitch signal transitions from logic high to logic low. Since both clocks are still functional during the manual switch, neither clkbad signal goes high. Because the switchover circuit is negative-edge sensitive, the rising edge of the extswitch signal does not cause the circuit to switch back from inclk1 to inclk0. When the extswitch signal goes low again, the process repeats.

The extswitch signal and automatic switch work only if the clock being switched to is available. If the clock is not available, the state machine waits until the clock is available.

Level Two Title