Ethernet Subsystem Intel® FPGA IP User Guide: Early Access Customer Release

Download PDF
ID 773413
Date 4/14/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Feature Description 3. Ethernet Subsystem Parameters 4. Subsystem Abstraction Layer (SAL) 5. Dynamic Reconfiguration Extension Subsystem 6. Interfaces and Signals 7. Recommended Clock Connections 8. Register Descriptions 9. Ethernet SS IP Example Design 10. Document Revision History for Ethernet Subsystem Intel FPGA IP User Guide: Early Access Customer Release
1. Introduction x
1.1. Supported Features 1.2. Getting Started 1.3. Resource Utilization
2. Feature Description x
2.1. Ethernet Subsystem Intel FPGA IP Overview 2.2. Supported Features
3. Ethernet Subsystem Parameters x
3.1. Parameter Editor Parameters 3.2. E-Tile Port Enablement Guidelines and Restrictions 3.3. F-tile Ethernet Port to PMA Channel Mapping
4. Subsystem Abstraction Layer (SAL) x
4.1. Subsystem Abstraction Layer (SAL) Commands
4.1. Subsystem Abstraction Layer (SAL) Commands x
4.1.1. NOP(0x0) 4.1.2. get_hssi_profile 4.1.3. set_hssi_profile 4.1.4. read_MAC_statistic (0x3) 4.1.5. get_mtu(0x4) 4.1.6. set_csr for E-Tile (0x5) 4.1.7. set_csr for F-Tile 4.1.8. get_csr for E-Tile (0x6) 4.1.9. get_csr for F-Tile 4.1.10. enable_loopback for E-Tile (0x7) 4.1.11. enable_loopback for F-Tile 4.1.12. disable_loopback for E-Tile (0x8) 4.1.13. disable_loopback for F-Tile 4.1.14. Reset MAC Statistics (0x9) 4.1.15. set_mtu for F-Tile 4.1.16. Ncsi_get_link_status 4.1.17. Reserved 4.1.18. firmware_version (0xFF)
6. Interfaces and Signals x
6.1. AXI4 Interfaces 6.2. Serial Interface 6.3. Clocks 6.4. Resets
6.1. AXI4 Interfaces x
6.1.1. AXI-Lite CSR 6.1.2. AXI-ST Client Interface 6.1.3. AXI-ST PHY Direct 6.1.4. AXI-ST PTP 6.1.5. Flow Control
7. Recommended Clock Connections x
7.1. Driving Multiple Ports with the Same Clock 7.2. Alternate Clock Connections for MAC Async Client FIFO 7.3. F-Tile Clock Connections for PTP Synchronous and Asynchronous cases 7.4. Clock Connections for SyncE Operation 7.5. F-Tile PMA and FEC Direct PHY IP Clock Output
8. Register Descriptions x
8.1. Subsystem Registers 8.2. Port Registers 8.3. F-tile Address Maps 8.4. F-tile ANLT Port Register Map 8.5. F-tile PTP Tile Adapter Register Map
8.1. Subsystem Registers x
8.1.1. Device Feature Header Lo 8.1.2. Device Feature Header Hi 8.1.3. Feature GUID_L 8.1.4. Feature GUID_H 8.1.5. Feature CSR ADDR 8.1.6. Feature CSR Size Group 8.1.7. Version 8.1.8. Feature List 8.1.9. Interface Attribute Port X Parameters 8.1.10. HSSI Command/Status 8.1.11. HSSI Control/Address 8.1.12. HSSI Read Data 8.1.13. HSSI Write Data 8.1.14. HSSI Ethernet Port X Status
8.2. Port Registers x
8.2.1. E-Tile PTP Packet Classifier Registers
8.2.1. E-Tile PTP Packet Classifier Registers x
8.2.1.1. Recognized and Unrecognized Packet Counters 8.2.1.2. Parse Graph Specific Packet Counters
9. Ethernet SS IP Example Design x
9.1. Steps to Generate the Example Design 9.2. Supported Simulators 9.3. Running the Simulation Tests 9.4. Running the Hardware Tests
9.3. Running the Simulation Tests x
9.3.1. Steps to Simulate the Design Example
9.4. Running the Hardware Tests x
9.4.1. Supported Boards 9.4.2. Steps to Compile the Design Example for Hardware 9.4.3. Steps to Run the Design Example on Hardware
1. Introduction
2. Feature Description
3. Ethernet Subsystem Parameters
4. Subsystem Abstraction Layer (SAL)
5. Dynamic Reconfiguration Extension Subsystem
6. Interfaces and Signals
7. Recommended Clock Connections
8. Register Descriptions
9. Ethernet SS IP Example Design
10. Document Revision History for Ethernet Subsystem Intel FPGA IP User Guide: Early Access Customer Release

7.2. Alternate Clock Connections for MAC Async Client FIFO

When "Enable asynchronous adapter clocks" is set to Enable (for E- and F- tile) and "Client Interface" is set to MAC Avalon ST (for F-tile) in the IP GUI, p<n>_app_ss_st_rx_clk and p<n>_app_ss_st_tx_clk can be asynchronous from each other and from o_p<n>_clk_pll. The only requirement on the clocks is that they be fast enough so that no data will be dropped by the port. No additional async FIFO or special data valid sequence is required in soft logic to use this mode.

Figure 10. Alternate Clock Connections for MAC+PCS Async Operation

The Tile Refclk/PLL IP and i_clk_sys is instantiated within HSSI SS and only applicable for F-tile.

Table 31.  Minimum Clock Rates for MAC Client Async FIFO Operation, Assuming 12 byte IPGThe following table shows the minimum rates required. Note that the 100G rate is lower because the MAC interface is 512b wide.
Rate Min p<n>_app_ss_st_tx_clk Min p<n>_app_ss_st_rx_clk
10G 156.25 MHz

o_p<n>_clk_rec_div or

156.25 +200 ppm for F-tile or 100 ppm for E-tile
25G/50G 390.625 MHz

o_p<n>_clk_rec_div or

390.625 MHz +200 ppm for F-tile or 100 ppm for E-tile
40G 312.5 MHz 312.5 +200 ppm for F-tile or 100 ppm for E-tile
100G

F-tile:

380 MHz (Preamble Passthrough Enabled)

340 MHz (Preamble Passthrough Disabled)

E-tile:

280.90 MHz (Preamble Passthrough Enabled)

240 MHz (Preamble Passthrough Disabled)

 F-tile:

380 MHz (Preamble Passthrough Enabled)

340 MHz (Preamble Passthrough Disabled)

E-tile:

280.90 MHz +100 ppm

240 MHz
Level Two Title