Intel® Stratix® 10 General Purpose I/O User Guide

Download PDF
ID 683518
Date 9/13/2023
Public
Document Table of Contents
Document Table of Contents x
1. Intel® Stratix® 10 I/O Overview 2. Intel® Stratix® 10 I/O Architecture and Features 3. Intel® Stratix® 10 I/O Design Considerations 4. Intel® Stratix® 10 I/O Implementation Guides 5. GPIO Intel® FPGA IP Reference 6. Document Revision History for Intel® Stratix® 10 General Purpose I/O User Guide
1. Intel® Stratix® 10 I/O Overview x
1.1. Intel® Stratix® 10 I/O and Differential I/O Buffers 1.2. Intel® Stratix® 10 I/O Migration Support
2. Intel® Stratix® 10 I/O Architecture and Features x
2.1. I/O Standards and Voltage Levels in Intel® Stratix® 10 Devices 2.2. I/O Element Structure in Intel® Stratix® 10 Devices 2.3. Programmable IOE Features in Intel® Stratix® 10 Devices 2.4. On-Chip I/O Termination in Intel® Stratix® 10 Devices 2.5. External I/O Termination for Intel® Stratix® 10 Devices
2.1. I/O Standards and Voltage Levels in Intel® Stratix® 10 Devices x
2.1.1. Intel® Stratix® 10 I/O Standards Support 2.1.2. Intel® Stratix® 10 I/O Standards Voltage Support
2.2. I/O Element Structure in Intel® Stratix® 10 Devices x
2.2.1. I/O Bank Architecture in Intel® Stratix® 10 Devices 2.2.2. I/O Buffer and Registers in Intel® Stratix® 10 Devices
2.3. Programmable IOE Features in Intel® Stratix® 10 Devices x
2.3.1. Programmable Output Slew Rate Control 2.3.2. Programmable IOE Delay 2.3.3. Programmable Open-Drain Output 2.3.4. Programmable Bus Hold 2.3.5. Programmable Pull-Up Resistor 2.3.6. Programmable Pre-Emphasis 2.3.7. Programmable Differential Output Voltage 2.3.8. Programmable Current Strength
2.4. On-Chip I/O Termination in Intel® Stratix® 10 Devices x
2.4.1. RS OCT without Calibration in Intel® Stratix® 10 Devices 2.4.2. RS OCT with Calibration in Intel® Stratix® 10 Devices 2.4.3. RT OCT with Calibration in Intel® Stratix® 10 Devices 2.4.4. Dynamic OCT 2.4.5. Differential Input RD OCT 2.4.6. OCT Calibration Block in Intel® Stratix® 10 Devices
2.5. External I/O Termination for Intel® Stratix® 10 Devices x
2.5.1. Single-Ended I/O Termination 2.5.2. Differential I/O Termination for Intel® Stratix® 10 Devices
2.5.2. Differential I/O Termination for Intel® Stratix® 10 Devices x
2.5.2.1. Differential HSTL, SSTL, HSUL, and POD Termination 2.5.2.2. LVDS, RSDS, and Mini-LVDS Termination 2.5.2.3. LVPECL Termination
3. Intel® Stratix® 10 I/O Design Considerations x
3.1. Guideline: VREF Sources and VREF Pins 3.2. Guideline: Observe Device Absolute Maximum Rating for 3.0 V Interfacing 3.3. Guideline: Voltage-Referenced and Non-Voltage Referenced I/O Standards 3.4. Guideline: Do Not Drive I/O Pins During Power Sequencing 3.5. Guideline: Intel® Stratix® 10 I/O Buffer During Power Up, Configuration, and Power Down 3.6. Guideline: Maximum DC Current Restrictions 3.7. Guideline: Use Only One Voltage for All 3 V I/O Banks 3.8. Guideline: I/O Standards Limitation for Intel® Stratix® 10 TX 400 3.9. Guideline: I/O Standards Limitation for Intel® Stratix® 10 GX 400 and SX 400
4. Intel® Stratix® 10 I/O Implementation Guides x
4.1. GPIO Intel® FPGA IP 4.2. Verifying Resource Utilization and Design Performance 4.3. GPIO Intel® FPGA IP Timing 4.4. GPIO Intel® FPGA IP Design Examples 4.5. Verifying Pin Migration Compatibility 4.6. IP Migration to the GPIO IP Core
4.1. GPIO Intel® FPGA IP x
4.1.1. Release Information for GPIO Intel® FPGA IP 4.1.2. GPIO Intel® FPGA IP Data Paths 4.1.3. Register Packing
4.1.2. GPIO Intel® FPGA IP Data Paths x
4.1.2.1. Input Path 4.1.2.2. Output and Output Enable Paths
4.3. GPIO Intel® FPGA IP Timing x
4.3.1. Timing Components 4.3.2. Delay Elements 4.3.3. Timing Analysis 4.3.4. Timing Closure Guidelines
4.3.3. Timing Analysis x
4.3.3.1. Single Data Rate Input Register 4.3.3.2. Full-Rate or Half-Rate DDIO Input Register 4.3.3.3. Single Data Rate Output Register 4.3.3.4. Full-Rate or Half-Rate DDIO Output Register
4.4. GPIO Intel® FPGA IP Design Examples x
4.4.1. GPIO Intel® FPGA IP Synthesizable Intel® Quartus® Prime Design Example 4.4.2. GPIO Intel® FPGA IP Simulation Design Example
4.6. IP Migration to the GPIO IP Core x
4.6.1. Migrating Your ALTDDIO_IN, ALTDDIO_OUT, ALTDDIO_BIDIR, and ALTIOBUF IP Cores 4.6.2. Guideline: Swap datain_h and datain_l Ports in Migrated IP
5. GPIO Intel® FPGA IP Reference x
5.1. GPIO Intel® FPGA IP Parameter Settings 5.2. GPIO Intel® FPGA IP Interface Signals
5.2. GPIO Intel® FPGA IP Interface Signals x
5.2.1. Shared Signals 5.2.2. Data Bit-Order for Data Interface 5.2.3. Data Interface Signals and Corresponding Clocks
1. Intel® Stratix® 10 I/O Overview
2. Intel® Stratix® 10 I/O Architecture and Features
3. Intel® Stratix® 10 I/O Design Considerations
4. Intel® Stratix® 10 I/O Implementation Guides
5. GPIO Intel® FPGA IP Reference
6. Document Revision History for Intel® Stratix® 10 General Purpose I/O User Guide

2.3. Programmable IOE Features in Intel® Stratix® 10 Devices

Table 4.   Intel® Stratix® 10 Programmable IOE Features Settings and Assignment Name
Feature

Setting

Condition

Intel® Quartus® Prime

Assignment Name
Slew Rate Control 0 (Slow), 1 (Fast). Default is 1. Disabled if you use the RS OCT feature. SLEW_RATE
I/O Delay Refer to the device datasheet —

INPUT_DELAY_CHAIN

OUTPUT_DELAY_CHAIN

Open-Drain Output On, Off. Default is Off — AUTO_OPEN_DRAIN_PINS
Bus-Hold On, Off. Default is Off. Disabled if you use the weak pull-up resistor feature. ENABLE_BUS_HOLD_CIRCUITRY
Weak Pull-up Resistor On, Off. Default is Off. Disabled if you use the bus-hold feature. WEAK_PULL_UP_RESISTOR
Pre-Emphasis 0 (disabled), 1 (enabled). Default is 1. — PROGRAMMABLE_PREEMPHASIS
Differential Output Voltage 0 (low), 1 (medium low), 2 (medium high), 3 (high). Default is 2. — PROGRAMMABLE_VOD
Table 5.   Intel® Stratix® 10 Programmable IOE Features I/O Buffer Types and I/O Standards SupportThis table lists the I/O buffer types and I/O standards that support the programmable IOE features. For information about which I/O standards are available for each I/O buffer type, refer to the related information.
Feature I/O Buffer Type Support

I/O Standards Support
LVDS I/O 3 V I/O

HPS I/O

(SoC Devices Only)

Slew Rate Control 11 Yes Yes Yes
  • 3.0 V /3.3 V LVTTL
  • 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.0 V/3.3 V LVCMOS
  • SSTL-18, SSTL-15, SSTL-135, SSTL-125, and SSTL-12
  • 1.2 V, 1.5 V, and 1.8 V HSTL
  • HSUL-12
  • POD12
  • Differential SSTL-18, Differential SSTL-15, Differential SSTL-135, Differential SSTL-125, and Differential SSTL-12
  • Differential 1.2 V, 1.5 V, and 1.8 V HSTL
  • Differential HSUL-12
I/O Delay Yes Yes —
Open-Drain Output11 Yes Yes Yes
  • 3.0 V LVTTL
  • 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.0 V LVCMOS
Bus-Hold11 Yes Yes —
Weak Pull-up Resistor11 Yes Yes Yes
Pre-Emphasis Yes — —
  • LVDS
  • RSDS
  • Mini-LVDS
  • LVPECL
  • With OCT fast slew rate mode:
    • POD12 and Differential POD12
    • SSTL-12 and Differential SSTL-12
Differential Output Voltage Yes — —
  • LVDS
  • RSDS
  • Mini-LVDS
  • LVPECL

Section Content
Programmable Output Slew Rate Control
Programmable IOE Delay
Programmable Open-Drain Output
Programmable Bus Hold
Programmable Pull-Up Resistor
Programmable Pre-Emphasis
Programmable Differential Output Voltage
Programmable Current Strength

Related Information
11 Not available for the 3.3 V I/O bank (bank 3C) of the HF35 package of the Intel® Stratix® 10 GX 400 and SX 400 devices.
Level Two Title