F-Tile CPRI PHY Intel® FPGA IP User Guide

Download PDF
ID 683284
Date 10/04/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile CPRI PHY Intel® FPGA IP Core 2. Getting Started 3. IP Parameter Settings 4. Functional Description 5. Interface Signals 6. IP Registers 7. F-Tile CPRI PHY Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile CPRI PHY Intel FPGA IP User Guide
1. About the F-Tile CPRI PHY Intel® FPGA IP Core x
1.1. Supported Features 1.2. Overview 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization 1.6. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the IP Core Parameters and Options 2.3. Generated File Structure 2.4. IP Core Testbenches
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.2. Specifying the IP Core Parameters and Options x
2.2.1. Reference and System PLL Clock for your IP Design
4. Functional Description x
4.1. Reset Logic 4.2. Latency Measurement
4.2. Latency Measurement x
4.2.1. Deterministic Latency 4.2.2. Calculation for 64b/66b Datapath
5. Interface Signals x
5.1. Clock Signals 5.2. Reset Signals 5.3. TX MII Interface (64b/66b) 5.4. RX MII Interface (64b/66b) 5.5. Status Interface for 64b/66b Line Rate 5.6. TX Interface (8b/10b) 5.7. RX Interface (8b/10b) 5.8. Status Interface for 8b/10b Line Rate 5.9. Serial Interface 5.10. Reconfiguration Interfaces
5.1. Clock Signals x
5.1.1. Required Clock Frequencies
5.10. Reconfiguration Interfaces x
5.10.1. CPRI PHY Reconfiguration Interface 5.10.2. Ethernet Reconfiguration Interface 5.10.3. Transceiver Reconfiguration Interface
1. About the F-Tile CPRI PHY Intel® FPGA IP Core
2. Getting Started
3. IP Parameter Settings
4. Functional Description
5. Interface Signals
6. IP Registers
7. F-Tile CPRI PHY Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile CPRI PHY Intel FPGA IP User Guide

2.2.1. Reference and System PLL Clock for your IP Design

Each F-tile system must instantiate one F-Tile Reference and System PLL Clocks Intel FPGA IP. The F-Tile Reference and System PLL Clocks Intel FPGA IP performs three main functions:
  1. Configure reference clock for FHT PMA:
    • Enable the FHT common PLLs and select the reference clock source for FHT common PLL
    • Specify the FHT reference clock source frequency
    Note: The F-Tile CPRI PHY Intel® FPGA IP core does not support FHT PMA. The IP core implementation uses FGT PMA.
  2. Configure reference clock for FGT PMA:
    • Enable FGT reference clocks and specify the reference clock frequency
    • Specify FGT CDR output
  3. Configure system PLL:
    • Enable system PLL and specify its mode
    • Specify the reference clock source and frequency for system PLL
Note: In your IP design, you must include an F-Tile Reference and System PLL Clocks Intel FPGA IP core to pass logic generation flow.

The F-Tile Reference and System PLL Clocks Intel FPGA IP must always connect to a protocol based Intel FPGA IP. The F-Tile Reference and System PLL Clocks Intel FPGA IP cannot be compiled or simulated as a standalone IP. For more information on parameters and port list for F-Tile Reference and System PLL Clocks Intel FPGA IP core, refer to the F-tile Architecture and PMA/FEC Direct PHY IP User Guide.

When you design multiple interfaces or protocol-based IP cores within a single F-tile, you must use only one instance of the F-Tile Reference and System PLL Clocks Intel FPGA IP core to configure:
  • All required reference clocks for FGT PMA (up to 10) and FHT PMA (up to 2) to implement multiple interfaces within a single F-tile.
  • All required FHT common PLLs (up to 2) to implement multiple interfaces within a single F-tile.
  • All required System PLLs (up to 3) to implement multiple interfaces within a single F-tile.
  • All required reference clocks for system PLLs (up to 8 – shared with FGT PMA) to implement multiple interfaces within a single F-tile.

When you design multiple interfaces or protocol-based IP cores within a single F-tile, you can only use three System PLLs. For example, you can use one System PLL for PCIe and two for Ethernet and other protocols. However, there are other use cases where you can use all three for various interfaces within the Ethernet and PMA-Direct digital blocks. As there are only three System PLLs, multiple interfaces or protocol-based IP cores with different line rates may have to share a System PLL. While sharing a System PLL, the interface with the highest line rate determines the system PLL frequency, and the interfaces with the lower line rates must be overclocked. For more information, refer to the F-tile Architecture and PMA/FEC Direct PHY IP User Guide.

Related Information
Level Two Title