Intel® Quartus® Prime Pro Edition User Guide: Timing Analyzer

Download PDF
ID 683243
Date 10/04/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Timing Analysis Introduction 2. Using the Intel® Quartus® Prime Timing Analyzer A. Intel® Quartus® Prime Pro Edition User Guides
1. Timing Analysis Introduction x
1.1. Timing Analysis Basic Concepts 1.2. Timing Analysis Overview Document Revision History
1.1. Timing Analysis Basic Concepts x
1.1.1. Timing Path and Clock Analysis 1.1.2. Clock Setup Analysis 1.1.3. Clock Hold Analysis 1.1.4. Recovery and Removal Analysis 1.1.5. Multicycle Path Analysis 1.1.6. Metastability Analysis 1.1.7. Timing Pessimism 1.1.8. Clock-As-Data Analysis 1.1.9. Multicorner Timing Analysis 1.1.10. Time Borrowing
1.1.1. Timing Path and Clock Analysis x
1.1.1.1. The Timing Netlist 1.1.1.2. Timing Paths 1.1.1.3. Data and Clock Arrival Times 1.1.1.4. Launch and Latch Edges
1.1.5. Multicycle Path Analysis x
1.1.5.1. Multicycle Clock Hold 1.1.5.2. Multicycle Clock Setup
1.1.10. Time Borrowing x
1.1.10.1. Time Borrowing Limitations 1.1.10.2. Time Borrowing with Latches
2. Using the Intel® Quartus® Prime Timing Analyzer x
2.1. Timing Analysis Flow 2.2. Step 1: Specify Timing Analyzer Settings 2.3. Step 2: Specify Timing Constraints 2.4. Step 3: Run the Timing Analyzer 2.5. Step 4: Analyze Timing Reports 2.6. Applying Timing Constraints 2.7. Timing Analyzer Tcl Commands 2.8. Timing Analysis of Imported Compilation Results 2.9. Using the Intel® Quartus® Prime Timing Analyzer Document Revision History 2.10. Intel® Quartus® Prime Pro Edition User Guide: Timing Analyzer Archive
2.4. Step 3: Run the Timing Analyzer x
2.4.1. Setting the Operating Conditions 2.4.2. Enabling Time Borrowing Optimization
2.5. Step 4: Analyze Timing Reports x
2.5.1. Generating Timing Reports 2.5.2. Cross-Probing with Design Assistant 2.5.3. Launching Design Assistant from Timing Analyzer 2.5.4. Locating Timing Paths in Other Tools 2.5.5. Correlating Constraints to the Timing Report
2.5.1. Generating Timing Reports x
2.5.1.1. Report Fmax Summary 2.5.1.2. Report Timing 2.5.1.3. Report Data Delay 2.5.1.4. Report Clocks and Clock Networks 2.5.1.5. Report Clock Transfers 2.5.1.6. Report Logic Depth 2.5.1.7. Report Neighbor Paths 2.5.1.8. Report Register Spread 2.5.1.9. Report Route Net of Interest 2.5.1.10. Report Retiming Restrictions 2.5.1.11. Report Reset Statistics 2.5.1.12. Report Pipelining Information 2.5.1.13. Report Asynchronous CDC 2.5.1.14. Report CDC Viewer 2.5.1.15. Report Time Borrowing Data 2.5.1.16. Report Exceptions and Exceptions Reachability
2.5.1.8. Report Register Spread x
2.5.1.8.1. Registers with High Timing Path Endpoint Tension 2.5.1.8.2. Registers with High Immediate Fan-Out Tension
2.5.2. Cross-Probing with Design Assistant x
2.5.2.1. Cross-Probing from Design Assistant to Timing Analyzer
2.6. Applying Timing Constraints x
2.6.1. Recommended Initial SDC Constraints 2.6.2. SDC File Precedence 2.6.3. Modifying Iterative Constraints 2.6.4. Using Entity-bound SDC Files 2.6.5. Creating Clocks and Clock Constraints 2.6.6. Creating I/O Constraints 2.6.7. Creating Delay and Skew Constraints 2.6.8. Creating Timing Exceptions 2.6.9. Using Fitter Overconstraints 2.6.10. Example Circuit and SDC File
2.6.1. Recommended Initial SDC Constraints x
2.6.1.1. Create Clock (create_clock) 2.6.1.2. Derive PLL Clocks (derive_pll_clocks) 2.6.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.6.1.4. Set Clock Groups (set_clock_groups)
2.6.4. Using Entity-bound SDC Files x
2.6.4.1. Entity-bound Constraint Scope 2.6.4.2. Entity-bound Constraint Examples
2.6.5. Creating Clocks and Clock Constraints x
2.6.5.1. Creating Base Clocks 2.6.5.2. Creating Virtual Clocks 2.6.5.3. Creating Generated Clocks (create_generated_clock) 2.6.5.4. Deriving PLL Clocks 2.6.5.5. Creating Clock Groups (set_clock_groups) 2.6.5.6. Accounting for Clock Effect Characteristics 2.6.5.7. Constraining CDC Paths
2.6.5.1. Creating Base Clocks x
2.6.5.1.1. Automatic Clock Detection and Constraint Creation
2.6.5.2. Creating Virtual Clocks x
2.6.5.2.1. Specifying I/O Interface Uncertainty 2.6.5.2.2. I/O Interface Clock Uncertainty Example
2.6.5.3. Creating Generated Clocks (create_generated_clock) x
2.6.5.3.1. Clock Divider Example (-divide_by) 2.6.5.3.2. Clock Multiplexer Example
2.6.5.5. Creating Clock Groups (set_clock_groups) x
2.6.5.5.1. Exclusive Clock Groups (-logically_exclusive or -physically_exclusive) 2.6.5.5.2. Asynchronous Clock Groups (-asynchronous) 2.6.5.5.3. set_clock_groups Constraint Tips
2.6.5.6. Accounting for Clock Effect Characteristics x
2.6.5.6.1. Set Clock Latency (set_clock_latency) 2.6.5.6.2. Clock Uncertainty
2.6.6. Creating I/O Constraints x
2.6.6.1. Input Constraints (set_input_delay) 2.6.6.2. Output Constraints (set_output_delay)
2.6.7. Creating Delay and Skew Constraints x
2.6.7.1. Advanced I/O Timing and Board Trace Model Delay 2.6.7.2. Maximum Skew (set_max_skew) 2.6.7.3. Net Delay (set_net_delay)
2.6.8. Creating Timing Exceptions x
2.6.8.1. Timing Exception Precedence 2.6.8.2. False Paths (set_false_path) 2.6.8.3. Minimum and Maximum Delays 2.6.8.4. Multicycle Paths 2.6.8.5. Multicycle Exception Examples 2.6.8.6. Delay Annotation 2.6.8.7. Constraining Design Partition Ports
2.6.8.4. Multicycle Paths x
2.6.8.4.1. Common Multicycle Applications 2.6.8.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.6.8.4.3. Accounting for a Phase Shift (-phase)
2.6.8.5. Multicycle Exception Examples x
2.6.8.5.1. Default Multicycle Analysis 2.6.8.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.6.8.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.6.8.5.4. Same Frequency Clocks with Destination Clock Offset 2.6.8.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.6.8.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.6.8.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.6.8.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.7. Timing Analyzer Tcl Commands x
2.7.1. The quartus_sta Executable 2.7.2. Collection Commands
2.7.2. Collection Commands x
2.7.2.1. Wildcard Characters 2.7.2.2. Adding and Removing Collection Items 2.7.2.3. Query of Collections 2.7.2.4. Using the get_pins Command
1. Timing Analysis Introduction
2. Using the Intel® Quartus® Prime Timing Analyzer
A. Intel® Quartus® Prime Pro Edition User Guides

2.6.7.3. Net Delay (set_net_delay)

Use the set_net_delay command to set the net delays and perform minimum or maximum timing analysis across nets. A net delay constraint is invalid if there is a combinational cell between the From and To nodes.

The -from and -to options can be string patterns or pin, port, register, or net collections. When you use pin or net collection, include output pins or nets in the collection. 

set_net_delay -from reg_a -to reg_c -max 20
Table 30.  set_net_delay Options
Arguments Description
-h | -help Short help.
-long_help Long help with examples and possible return values.
-from <names> 3 Valid source pins, ports, registers or nets (Tcl matches string patterns).
-get_value_from_clock_period <src_clock_period|dst_clock_period|min_clock_period|max_clock_period> Option to interpret net delay constraint as a multiple of the clock period.
-max Specifies maximum delay.
-min Specifies minimum delay.
-to <names> 4 Valid destination pins, ports, registers or nets (Tcl matches string patterns).
-value_multiplier <multiplier> Value by which the clock period multiplies to compute net delay requirement.
<delay> Delay value.

If you use the -min option, the Timing Analyzer calculates slack by determining the minimum delay on the edge. If you use -max option, the Timing Analyzer calculates slack by determining the maximum edge delay.

Use -get_value_from_clock_period to set the net delay requirement as a multiple of the launching or latching clock period, or whichever of the two has a smaller or larger period. If you use this option, you must not set the positional delay option. If more than one clock clocks the set of nets, the Timing Analyzer uses the net with the smallest period to compute the constraint for a -max constraint, and the largest period for a -min constraint. If no clocks are clocking the endpoints of the net (that is, if the endpoints of the nets are not registers or constraint ports), the Timing Analyzer ignores the net delay constraint.

Related Information
3 If option is a wildcard ( "*") character, all the output pins and registers on timing netlist become valid source points.
4 If no option, or if option is a wildcard ( "*") character, all the output pins and registers on timing netlist become valid destination points.
Level Two Title