Visible to Intel only — GUID: zps1478130566759
Ixiasoft
2.1. Installation and Licensing for LL 100GbE IP Core for Stratix® V Devices
2.2. Installing and Licensing Intel® FPGA IP Cores
2.3. Specifying the IP Core Parameters and Options
2.4. IP Core Parameters
2.5. Files Generated for Stratix V Variations
2.6. Files Generated for Arria 10 Variations
2.7. Integrating Your IP Core in Your Design
2.8. IP Core Testbenches
2.9. Compiling the Full Design and Programming the FPGA
2.10. Initializing the IP Core
2.7.1. Pin Assignments
2.7.2. External Transceiver Reconfiguration Controller Required in Stratix V Designs
2.7.3. Transceiver PLL Required in Arria 10 Designs
2.7.4. Handling Potential Jitter in Intel® Arria® 10 Devices
2.7.5. External Time-of-Day Module for Variations with 1588 PTP Feature
2.7.6. External TX MAC PLL
2.7.7. Placement Settings for the LL 100GbE Core
3.2.1. LL 100GbE IP Core TX Datapath
3.2.2. LL 100GbE IP Core TX Data Bus Interfaces
3.2.3. LL 100GbE IP Core RX Datapath
3.2.4. LL 100GbE IP Core RX Data Bus Interfaces
3.2.5. Low Latency 100GbE CAUI–4 PHY
3.2.6. External Reconfiguration Controller
3.2.7. External Transceiver PLL
3.2.8. External TX MAC PLL
3.2.9. Congestion and Flow Control Using Pause Frames
3.2.10. Pause Control and Generation Interface
3.2.11. Pause Control Frame Filtering
3.2.12. Link Fault Signaling Interface
3.2.13. Statistics Counters Interface
3.2.14. 1588 Precision Time Protocol Interfaces
3.2.15. PHY Status Interface
3.2.16. Transceiver PHY Serial Data Interface
3.2.17. Control and Status Interface
3.2.18. Arria 10 Transceiver Reconfiguration Interface
3.2.19. Clocks
3.2.20. Resets
3.2.2.1. LL 100GbE IP Core User Interface Data Bus
3.2.2.2. LL 100GbE IP Core TX Data Bus with Adapters (Avalon-ST Interface)
3.2.2.3. LL 100GbE IP Core TX Data Bus Without Adapters (Custom Streaming Interface)
3.2.2.4. Bus Quantization Effects With Adapters
3.2.2.5. User Interface to Ethernet Transmission
3.2.3.1. LL 100GbE IP Core RX Filtering
3.2.3.2. LL 100GbE IP Core Preamble Processing
3.2.3.3. LL 100GbE IP Core FCS (CRC-32) Removal
3.2.3.4. LL 100GbE IP Core CRC Checking
3.2.3.5. LL 100GbE IP Core Malformed Packet Handling
3.2.3.6. RX CRC Forwarding
3.2.3.7. Inter-Packet Gap
3.2.3.8. RX RSFEC
3.2.3.9. Pause Ignore
3.2.3.10. Control Frame Identification
3.4.1.1. PHY Registers
3.4.1.2. Link Fault Signaling Registers
3.4.1.3. LL 100GbE IP Core MAC Configuration Registers
3.4.1.4. Pause Registers
3.4.1.5. TX Statistics Registers
3.4.1.6. RX Statistics Registers
3.4.1.7. 1588 PTP Registers
3.4.1.8. TX Reed-Solomon FEC Registers
3.4.1.9. RX Reed-Solomon FEC Registers
Visible to Intel only — GUID: zps1478130566759
Ixiasoft
3.2. LL 100GbE IP Core Functional Description
The LL 100GbE IP core implements the 100GbE Ethernet MAC in accordance with the IEEE 802.3ba 2010 High Speed Ethernet Standard. This IP core handles the frame encapsulation and flow of data between a client logic and Ethernet network via a 100GbE Ethernet PCS and PMA (PHY).
In the transmit direction, the MAC accepts client frames, and inserts inter-packet gap (IPG), preamble, start of frame delimiter (SFD), padding, and CRC bits before passing them to the PHY. The PHY encodes the MAC frame as required for reliable transmission over the media to the remote end.
In the receive direction, the PHY passes frames to the MAC. The MAC accepts frames from the PHY, performs checks, updates statistics counters, strips out the CRC, preamble, and SFD, and passes the rest of the frame to the client. In RX preamble pass-through mode, the MAC passes on the preamble and SFD to the client instead of stripping them out. In RX CRC pass-through mode (bit 1 of the CRC_CONFIG register has the value of 1), the MAC passes on the CRC bytes to the client and asserts the EOP signal in the same clock cycle with the final CRC byte.
The LL 100GbE IP core includes the following interfaces:
- Datapath client-interface–The following options are available:
- With adapters—Avalon-ST, 512 bits
- Custom streaming, 256 bits
- Management interface—Avalon-MM host slave interface for MAC management. This interface has a data width of 32 bits and an address width of 16 bits.
- Datapath Ethernet interface–The following options are available:
- CAUI: Ten 10.3125 Gbps serial links
- CAUI–4: Four 25.78125 Gbps serial links
- In Arria 10 variations, an Arria 10 dynamic reconfiguration interface—an Avalon-MM interface to read and write the Arria 10 Native PHY IP core registers. This interface supports dynamic reconfiguration of the transceiver. LL 100GbE IP cores that target an Arria 10 device use the Arria 10 Native PHY IP core to configure the Ethernet link serial transceivers on the device. This interface has a data width of 32 bits. This interface has an address width of 12 bits for CAUI-4 variations, and an address width of 14 bits for standard variations.
Section Content
LL 100GbE IP Core TX Datapath
LL 100GbE IP Core TX Data Bus Interfaces
LL 100GbE IP Core RX Datapath
LL 100GbE IP Core RX Data Bus Interfaces
Low Latency 100GbE CAUI–4 PHY
External Reconfiguration Controller
External Transceiver PLL
External TX MAC PLL
Congestion and Flow Control Using Pause Frames
Pause Control and Generation Interface
Pause Control Frame Filtering
Link Fault Signaling Interface
Statistics Counters Interface
1588 Precision Time Protocol Interfaces
PHY Status Interface
Transceiver PHY Serial Data Interface
Control and Status Interface
Arria 10 Transceiver Reconfiguration Interface
Clocks
Resets