Nios® II Flash Programmer User Guide

Download PDF
ID 683118
Date 11/06/2017
Public
Document Table of Contents
Document Table of Contents x
1. Overview of the Nios® II Flash Programmer 2. Using the Flash Programmer GUI 3. Using the Flash Programmer from the Command Line A. Non-Standard Flash Memories B. Troubleshooting C. Document Revision History
1. Overview of the Nios® II Flash Programmer x
1.1. Prerequisites 1.2. Nios® II Flash Programmer GUI and Command-Line Utilities 1.3. How the Flash Programmer Works 1.4. Document Revision History for Overview of the Nios® II Flash Programmer
1.3. How the Flash Programmer Works x
1.3.1. Flash Programmer Target Design
2. Using the Flash Programmer GUI x
2.1. Starting the Flash Programmer GUI 2.2. Specifying your Flash Programmer Settings 2.3. Working with Flash Programmer Settings Files 2.4. Setting the Hardware Connection 2.5. Checking System ID and System Timestamp 2.6. Generating Flash Files and Programming Flash Memory 2.7. Document Revision History for Using the Flash Programmer GUI
3. Using the Flash Programmer from the Command Line x
3.1. quartus_pgm --nios2 3.2. sof2flash 3.3. elf2flash 3.4. bin2flash 3.5. Document Revision History for Using the Flash Programmer from the Command Line
3.1. quartus_pgm --nios2 x
3.1.1. quartus_pgm --nios2 Parameters 3.1.2. quartus_pgm --nios2 Command-Line Examples
3.1.1. quartus_pgm --nios2 Parameters x
3.1.1.1. General Parameters 3.1.1.2. Device Parameters
3.2. sof2flash x
3.2.1. sof2flash Parameters 3.2.2. sof2flash Command-Line Examples
3.2.1. sof2flash Parameters x
3.2.1.1. General Parameters 3.2.1.2. Device Parameters 3.2.1.3. Configuration-Specific Parameters
3.3. elf2flash x
3.3.1. elf2flash Parameters 3.3.2. Programming Both Hardware and Software into an EPCS/EPCQ Device 3.3.3. elf2flash Command-Line Examples
3.3.1. elf2flash Parameters x
3.3.1.1. General Parameters 3.3.1.2. CFI Parameters 3.3.1.3. EPCS Parameters
3.4. bin2flash x
3.4.1. bin2flash Parameters 3.4.2. bin2flash Command-Line Example
A. Non-Standard Flash Memories x
A.1. Built-in Recognition and Override A.2. Flash Override Files A.3. Width Mode Override Parameter A.4. Document Revision History for Non-Standard Flash Memories
A.2. Flash Override Files x
A.2.1. Flash Override File Format A.2.2. How to Use the Flash Override File
B. Troubleshooting x
B.1. Overview B.2. Start Button Grayed Out in the Flash Programmer GUI B.3. 'No Nios® II Processors Available' Error B.4. 'No CFI Table Found' Error B.5. 'No EPCS Registers Found' Error B.6. 'System Does Not Have Any Flash Memory' Error B.7. 'Reading System ID at Address 0x<address>: FAIL' Error B.8. 'Base Address Not Aligned on Size of Device' Error B.9. Document Revision History for Troubleshooting
B.2. Start Button Grayed Out in the Flash Programmer GUI x
B.2.1. Probable Cause B.2.2. Suggested Actions
B.3. 'No Nios® II Processors Available' Error x
B.3.1. Probable Cause B.3.2. Suggested Actions
B.4. 'No CFI Table Found' Error x
B.4.1. Probable Cause B.4.2. Suggested Actions
B.5. 'No EPCS Registers Found' Error x
B.5.1. Probable Cause B.5.2. Suggested Actions
B.6. 'System Does Not Have Any Flash Memory' Error x
B.6.1. Probable Cause B.6.2. Suggested Actions
B.7. 'Reading System ID at Address 0x<address>: FAIL' Error x
B.7.1. Probable Cause B.7.2. Suggested Actions
B.8. 'Base Address Not Aligned on Size of Device' Error x
B.8.1. Probable Cause B.8.2. Suggested Actions
1. Overview of the Nios® II Flash Programmer
2. Using the Flash Programmer GUI
3. Using the Flash Programmer from the Command Line
A. Non-Standard Flash Memories
B. Troubleshooting
C. Document Revision History

1.2. Nios® II Flash Programmer GUI and Command-Line Utilities

You can run the Nios® II Flash Programmer from a GUI or from the command line. The GUI displays the command-line equivalents of the actions you direct it to perform.

For more information about the flash programmer GUI, refer to "Using the Flash Programmer GUI" chapter.

For more information about using the flash programmer command-line utilities, refer to "Using the Flash Programmer from the Command Line" chapter.

The following tools allow you to run the Nios® II Flash Programmer:

  • Nios® II Software Build Tools for Eclipse™ – The Nios® II Software Build Tools (SBT) for Eclipse provides easy access to the Nios® II Flash Programmer GUI. The flash programmer GUI is an easy-to-use interface that allows you to control the flash programmer features using settings you can store and reuse. This access method is suitable for most flash programming needs.
  • Nios® II Command Shell – The Nios® II Command Shell provides commands that control the flash programmer features. You might have to calculate some parameters, manually. You can also start the Nios® II Flash Programmer GUI from the command line.
Related Information
Level Two Title