Intel Agilex® 7 FPGA F-Series Development Kit User Guide

Download PDF
ID 683024
Date 1/18/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Powering Up the Development Kit 4. Board Test System 5. Development Kits Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Intel Agilex® 7 FPGA F-Series Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Box Contents 1.3. Operating Conditions
2. Getting Started x
2.1. Software and Driver Installation 2.2. Design Examples
3. Powering Up the Development Kit x
3.1. Default Settings 3.2. Power Up
4. Board Test System x
4.1. Setting Up the BTS GUI Running Environment 4.2. Test the functionality of the Development Kit 4.3. Control on-board clock through Clock Controller GUI 4.4. Control on-board power regulator through Power Monitor GUI
4.1. Setting Up the BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Installing the Intel® Quartus® Prime Software 4.1.5. Running the BTS GUI
4.2. Test the functionality of the Development Kit x
4.2.1. The Configure Menu 4.2.2. The Sys Info Tab 4.2.3. The GPIO Tab 4.2.4. The QSFPDD Tab 4.2.5. The DDR4-0 Tab 4.2.6. The DDR4-2 Tab Start Stop Performance Indicators Error Control Number of Addresses to Read and Write 4.2.7. The DDR4-3 Tab 4.2.8. Identify Test Pass/Fail based on BTS GUI test status
5. Development Kits Hardware and Configuration x
5.1. Configure the FPGA and access HPS Debug Access Port by JTAG 5.2. Configure the FPGA device by AS modes (Default Mode)
6. Custom Projects for the Development Kit x
6.1. Add SmartVID settings in the QSF file 6.2. Golden Top
A. Development Kit Components x
A.1. Intel Agilex® 7 FPGA A.2. Configuration Support A.3. Clocks A.4. Memory Interfaces A.5. Transceiver Interfaces A.6. HPS Interface A.7. General Input and Output A.8. Power
A.2. Configuration Support x
A.2.1. JTAG Chain and Header A.2.2. On-board Intel® FPGA Download Cable II
A.7. General Input and Output x
A.7.1. Switches A.7.2. Buttons A.7.3. LEDs
A.8. Power x
A.8.1. Power Sequence A.8.2. Power Measurement A.8.3. Temperature Monitor
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Powering Up the Development Kit
4. Board Test System
5. Development Kits Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Intel Agilex® 7 FPGA F-Series Development Kit User Guide
A. Development Kit Components
B. Additional Information

4.2.6. The DDR4-2 Tab

This tab allows you to read and write DDR4-2 memory on your board.

Figure 13. The DDR4-2 Tab

The following sections describe the controls on this tab.

Start

Initiates DDR4 memory transaction performance analysis.

Stop

Terminates transaction performance analysis.

Performance Indicators

These controls display current transaction performance analysis information collected since you last clicked Start:
  • Write, Read and Total performance bars: Show the percentage of maximum theoretical data rate that the requested transactions are able to achieve.
  • Write (MBps), Read (MBps) and Total (MBps): Show the number of bytes analyzed per second.
  • Data Bus: 72 bits (8 bits ECC) wide, reference clock is 33.33 MHz and the frequency is 1066 MHz double data rate 2133 MT/s.

Error Control

This control displays data errors detected during analysis and allows you to insert errors:
  • Detected Errors: Displays the number of data errors detected in the hardware.
  • Inserted Errors: Displays the number of errors inserted into the transaction stream.
  • Insert: Inserts a one-word error into the transaction stream each time you click the button. Insert Error is only enabled during transaction performance analysis.
  • Clear: Resets the detected error and inserted error counters to zeroes.

Number of Addresses to Read and Write

Determines the number of addresses to use in each iteration of reads and writes.

Level Two Title