Intel Agilex® 7 FPGA F-Series Development Kit User Guide

Download PDF
ID 683024
Date 1/18/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Powering Up the Development Kit 4. Board Test System 5. Development Kits Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Intel Agilex® 7 FPGA F-Series Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Box Contents 1.3. Operating Conditions
2. Getting Started x
2.1. Software and Driver Installation 2.2. Design Examples
3. Powering Up the Development Kit x
3.1. Default Settings 3.2. Power Up
4. Board Test System x
4.1. Setting Up the BTS GUI Running Environment 4.2. Test the functionality of the Development Kit 4.3. Control on-board clock through Clock Controller GUI 4.4. Control on-board power regulator through Power Monitor GUI
4.1. Setting Up the BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Installing the Intel® Quartus® Prime Software 4.1.5. Running the BTS GUI
4.2. Test the functionality of the Development Kit x
4.2.1. The Configure Menu 4.2.2. The Sys Info Tab 4.2.3. The GPIO Tab 4.2.4. The QSFPDD Tab 4.2.5. The DDR4-0 Tab 4.2.6. The DDR4-2 Tab 4.2.7. The DDR4-3 Tab 4.2.8. Identify Test Pass/Fail based on BTS GUI test status
5. Development Kits Hardware and Configuration x
5.1. Configure the FPGA and access HPS Debug Access Port by JTAG 5.2. Configure the FPGA device by AS modes (Default Mode)
6. Custom Projects for the Development Kit x
6.1. Add SmartVID settings in the QSF file 6.2. Golden Top
A. Development Kit Components x
A.1. Intel Agilex® 7 FPGA A.2. Configuration Support A.3. Clocks A.4. Memory Interfaces A.5. Transceiver Interfaces A.6. HPS Interface A.7. General Input and Output A.8. Power
A.2. Configuration Support x
A.2.1. JTAG Chain and Header A.2.2. On-board Intel® FPGA Download Cable II
A.7. General Input and Output x
A.7.1. Switches A.7.2. Buttons A.7.3. LEDs
A.8. Power x
A.8.1. Power Sequence A.8.2. Power Measurement A.8.3. Temperature Monitor
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Powering Up the Development Kit
4. Board Test System
5. Development Kits Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Intel Agilex® 7 FPGA F-Series Development Kit User Guide
A. Development Kit Components
B. Additional Information

5.2. Configure the FPGA device by AS modes (Default Mode)

Default SW1 setting and system Intel® MAX® 10 image support AS configuration mode. Power on and observe FPGA D13 Configuration LED behavior.

The Intel Agilex® 7 FPGA F-Series Development Kit also supports some HPS interfaces. You can demonstrate the following HPS functions on this board:
  • 10/100/1000Mbps Ethernet PHY: U7_KSZ9031 and RJ45 connector J6
  • USB UART for communication port: micro USB connector J10
  • SD socket: J11
  • eMMC on board: U16_MTFC8GAKAJCN-4M
  • Mictor Connector for debug: J12
Level Two Title