GTS Interlaken Intel® FPGA IP User Guide

Download PDF
ID 819200
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the GTS Interlaken Intel® FPGA IP 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Interface Signals 6. GTS Interlaken IP Registers 7. GTS Interlaken FPGA IP User Guide Archives 8. Document Revision History for GTS Interlaken Intel FPGA IP User Guide
1. About the GTS Interlaken Intel® FPGA IP x
1.1. GTS Interlaken IP Features 1.2. GTS Interlaken IP Device Family Support 1.3. Device Speed Grade Support 1.4. GTS Interlaken IP Performance and Resources 1.5. GTS Interlaken IP Round-Trip Latency 1.6. GTS Interlaken IP Release Information
2. Getting Started x
2.1. Installing and Licensing Intel FPGA IPs 2.2. Generated File Structure 2.3. Specifying the GTS Interlaken IP Parameters and Options 2.4. Reference and System PLL Clock for Your IP Design 2.5. Simulating the GTS Interlaken IP 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel FPGA IPs x
2.1.1. Intel FPGA Evaluation Mode
3. Parameter Settings x
3.1. Analog Parameters for GTS IPs
4. Functional Description x
4.1. Datapath Flow 4.2. Modes of Operation 4.3. Performance 4.4. IP Reset 4.5. M20K ECC Support 4.6. Out-of-Band Flow Control
4.1. Datapath Flow x
4.1.1. Interlaken TX Path 4.1.2. Interlaken RX Path
4.1.1. Interlaken TX Path x
4.1.1.1. Transmit Path Blocks 4.1.1.2. In-Band Calendar Bits on Transmit Side
4.1.2. Interlaken RX Path x
4.1.2.1. Receive Path Blocks 4.1.2.2. In-Band Calendar Bits on Receive Side 4.1.2.3. RX Errored Packet Handling
4.1.2.3. RX Errored Packet Handling x
4.1.2.3.1. Example With Errors and In-Band Calendar Bits
4.2. Modes of Operation x
4.2.1. Interleaved and Packet Modes 4.2.2. Multisegments
4.2.1. Interleaved and Packet Modes x
4.2.1.1. Transmit User Data Interface Examples 4.2.1.2. Receive User Data Interface Examples
4.2.2. Multisegments x
4.2.2.1. Two-segment Interface Example
5. Interface Signals x
5.1. GTS Interlaken IP Clock and Reset Interface Signals 5.2. GTS Interlaken IP Transmit User Interface Signals 5.3. GTS Interlaken IP Receive User Interface Signals 5.4. GTS Interlaken IP Management Interface Signals 5.5. GTS Interlaken Link and Miscellaneous Signals 5.6. GTS Interlaken IP Reconfiguration Signals
1. About the GTS Interlaken Intel® FPGA IP
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Interface Signals
6. GTS Interlaken IP Registers
7. GTS Interlaken FPGA IP User Guide Archives
8. Document Revision History for GTS Interlaken Intel FPGA IP User Guide

4.4. IP Reset

The Interlaken IP variations have a single asynchronous reset, the reset_n signal. The Interlaken IP manages the initialization sequence internally. After you de-assert reset_n (raise it after asserting it low), the IP automatically goes through the entire reset sequence.

The reset_n signal only reset the IP, while the tx_rst_n and rx_rst_n signals reset the soft reset controller in Direct-PHY IP.

The tx_rst_ack_n and rx_rst_ack_n are active low asynchronous reset acknowledge signals from Direct-PHY IP which indicate that the soft reset controller has successfully entered reset mode and you can now release the reset_n, tx_rst_n, and rx_rst_n signals. The tx_rst_ack_n and rx_rst_ack_n signals stay low until you release the tx_rst_n, and rx_rst_n signals respectively.
Figure 16. Reset Timing Diagram

Following completion of the reset sequence internally, the Interlaken IP begins link initialization. If your IP and its Interlaken link partner initialize the link successfully, you can observe the assertion of the lane and link status signals according to the Interlaken specification. For example, you can monitor the tx_lanes_aligned, sync_locked, word_locked, and rx_lanes_aligned output status signals.

Level Two Title