F-Tile HDMI Intel® FPGA IP Design Example User Guide

Download PDF
ID 709314
Date 6/06/2024
Public
Document Table of Contents
Document Table of Contents x
1. HDMI Intel® FPGA IP Design Example Quick Start Guide for Agilex™ 7 F-Tile Devices 2. HDMI 2.1 Design Example (Support FRL = 1, Enable Active Video Protocol = None) 3. HDMI 2.1 Design Example with AXI4-stream Interface Enabled (Support FRL =1, Enable Active Video Protocol = AXIS-VVP Full) 4. Document Revision History for the F-Tile HDMI Intel® FPGA IP Design Example User Guide
1. HDMI Intel® FPGA IP Design Example Quick Start Guide for Agilex™ 7 F-Tile Devices x
1.1. Directory Structure 1.2. Generating the Design 1.3. Simulating the Design 1.4. Compiling and Testing the Design
2. HDMI 2.1 Design Example (Support FRL = 1, Enable Active Video Protocol = None) x
2.1. Design Features 2.2. Hardware and Software Requirements 2.3. HDMI 2.1 RX-TX Retransmit Design Block Diagram 2.4. Design Parameters 2.5. Design Components 2.6. Design Software Flow 2.7. Clocking Scheme 2.8. Interface Signals 2.9. Hardware Setup 2.10. Simulation Testbench 2.11. Debugging Features
2.3. HDMI 2.1 RX-TX Retransmit Design Block Diagram x
2.3.1. Creating RX-Only or TX-Only Designs
2.4. Design Parameters x
2.4.1. IP Parameters 2.4.2. HDMI Intel® FPGA IP Design Example Parameters
2.5. Design Components x
2.5.1. HDMI TX Components 2.5.2. HDMI RX Components 2.5.3. Top-Level Common Blocks
2.5.1. HDMI TX Components x
2.5.1.1. TX PHY Adapter
2.5.1.1. TX PHY Adapter x
2.5.1.1.1. FRL and TMDS
2.5.2. HDMI RX Components x
2.5.2.1. RX PHY Adapter
2.11. Debugging Features x
2.11.1. Software Debug Message 2.11.2. SCDC Information from Sink Connected to TX 2.11.3. Clock Frequency Measurement
3. HDMI 2.1 Design Example with AXI4-stream Interface Enabled (Support FRL =1, Enable Active Video Protocol = AXIS-VVP Full) x
3.1. Design Features 3.2. Hardware and Software Requirements 3.3. HDMI 2.1 RX-TX Retransmit Design Block Diagrams 3.4. Design Parameters 3.5. Design Components 3.6. Design Software Flow 3.7. Clocking Scheme 3.8. Interface Signals 3.9. Hardware Setup 3.10. Design Limitation (AXI/CV)
3.3. HDMI 2.1 RX-TX Retransmit Design Block Diagrams x
3.3.1. HDMI 2.1 RX-TX Direct Retransmit Design Block Diagram (Without Video Frame Buffer) 3.3.2. HDMI 2.1 RX-TX Retransmit Design Block Diagram (With Video Frame Buffer)
3.4. Design Parameters x
3.4.1. HDMI RX Direction 3.4.2. HDMI TX Direction
3.6. Design Software Flow x
3.6.1. Configure Redriver Setting 3.6.2. Initialize TX Path 3.6.3. Initialize RX Path 3.6.4. Initialize HDMI TX Register 3.6.5. Wait for RX Path Ready 3.6.6. TX Reconfiguration and Link Training 3.6.7. Set TX Video Clock 3.6.8. Set AXI2CV Configuration 3.6.9. HDMI TX Transmit Video
3.7. Clocking Scheme x
3.7.1. HDMI 2.1 RX-TX Retransmit Design without Video Frame Buffer (Enable Active Video Protocol = AXIS-VVP Full, Video In and Out Use the Same Clock = ON) 3.7.2. HDMI 2.1 RX-TX Retransmit Design with Video Frame Buffer (Enable Active Video Protocol = AXIS-VVP Full, Video In and Out Use the Same = OFF) 3.7.3. Clock Details
3.8. Interface Signals x
3.8.1. Platform Design System
3.9. Hardware Setup x
3.9.1. Supporting Additional Video Resolutions
1. HDMI Intel® FPGA IP Design Example Quick Start Guide for Agilex™ 7 F-Tile Devices
2. HDMI 2.1 Design Example (Support FRL = 1, Enable Active Video Protocol = None)
3. HDMI 2.1 Design Example with AXI4-stream Interface Enabled (Support FRL =1, Enable Active Video Protocol = AXIS-VVP Full)
4. Document Revision History for the F-Tile HDMI Intel® FPGA IP Design Example User Guide

2.5.1.1. TX PHY Adapter

To support HDMI, TX PMA Direct PHY is configured to 64 bits parallel data width. Due to the HDMI TX inter-lane skew requirement for HDMI 1.4, HDMI 2.0 and HDMI 2.1, certain HDMI data rate needs to be oversampled to 24 Gbps to meet the inter-lane skew. Due to the maximum system clock frequency of 900 MHz, the TX PHY needs to be configured to 64 bits (32 bits PMA width with byte serializer turned on) which results in the PMA clock of 750 MHz.

In the TX PMA Direct PHY architecture with the system PLL, a DCFIFO is required to clock the TX parallel data from the link speed clock (data rate/effective transceiver width) to the system clock (sys_clk_div2) domain.

Figure 13. 80 bits to 128 bits Converter

An 80 bits to 128 bits converter is designed with four 80 bits register to store the TX parallel data from the TX core. The first 128 bits data is outputted after the third clock cycle. After that, 128 bits data is outputted at the next five consecutive clock cycles. The process is repeated for every 8-clock cycle.


Section Content
FRL and TMDS

Level Two Title