AN 755: Implementing JESD204B IP Core System Reference Design with ARM HPS As Control Unit (Baremetal Flow)

Download PDF
ID 683776
Date 12/30/2015
Public
Document Table of Contents
Document Table of Contents x
1. Implementing JESD204B IP Core System Reference Design with ARM HPS As Control Unit (Baremetal Flow)
1. Implementing JESD204B IP Core System Reference Design with ARM HPS As Control Unit (Baremetal Flow) x
1.1. Reference Design Overview 1.2. Getting Started 1.3. Reference Design Components 1.4. Reference Design Files 1.5. FPGA Pin Assignments 1.6. System Parameters 1.7. Reference Design Software 1.8. Customizing the Reference Design 1.9. AN 755 Document Revision History
1.2. Getting Started x
1.2.1. Hardware and Software Requirements 1.2.2. Hardware Setup 1.2.3. Compiling the HDL and Programming the Board 1.2.4. Setting up the Software Command Line Environment
1.3. Reference Design Components x
1.3.1. Qsys System 1.3.2. Core PLL 1.3.3. Transport Layer 1.3.4. Test Pattern Generator 1.3.5. Test Pattern Checker
1.3.1. Qsys System x
1.3.1.1. Top Level Qsys Address Map 1.3.1.2. ARM HPS Control Unit and Supporting Processor Peripherals 1.3.1.3. JESD204B Subsystem
1.3.1.2. ARM HPS Control Unit and Supporting Processor Peripherals x
1.3.1.2.1. ARM HPS Control Unit 1.3.1.2.2. FPGA Core Control and Status PIO 1.3.1.2.3. SPI Master Module
1.3.1.3. JESD204B Subsystem x
1.3.1.3.1. JESD204B IP Core 1.3.1.3.2. Reset Sequencer 1.3.1.3.3. Transceiver PHY Reset Controller 1.3.1.3.4. Avalon-MM Bridge 1.3.1.3.5. JESD204B Subsystem Address Map
1.7. Reference Design Software x
1.7.1. User Commands 1.7.2. Dynamic Reconfiguration 1.7.3. Software Interrupt Service Routines (ISR) 1.7.4. Software Parameters 1.7.5. Software Functions Description
1.7.5. Software Functions Description x
1.7.5.1. Functions in main.c Source File 1.7.5.2. Functions in rules.c Source File 1.7.5.3. Custom Peripheral Access Macros in macros.c Source File
1.8. Customizing the Reference Design x
1.8.1. Modifying JESD204B IP Core Parameters 1.8.2. Modifying the Data Rate or Reference Clock Frequency 1.8.3. Implementing a Multi-Link Design
1.8.3. Implementing a Multi-Link Design x
1.8.3.1. Editing the Qsys Project 1.8.3.2. Editing the Top Level HDL File 1.8.3.3. Editing the Software Source Code
1. Implementing JESD204B IP Core System Reference Design with ARM HPS As Control Unit (Baremetal Flow)

1.2.2. Hardware Setup

  1. Install the ADI AD9680 converter card module to the FMC port A (J26) on the Arria V SoC development board.
  2. Connect the USB cable to the USB-Blaster® II connector on the development board.
  3. Connect the power adapter shipped with the development board to the power supply jack (J34).
  4. Connect the AD9516 power adapter to the power supply jack on the AD9516 clock module card.
  5. Connect the USB cable from your workstation to the USB connector on the AD9516 card.
  6. Connect the AD9516 clock module OUT0 SMA connector (J0A) to the CLKIN SMA connector (J801) on the AD9680 card.
  7. Connect the AD9516 clock module OUT8 SMA connector (J8A) to the Refclk to FPGA SMA connector (J804) on the AD9680 card.
  8. Turn on the power for the AD9516 clock module card.
  9. Configure the clock settings of the AD9516 to output 614.4 MHz clock for the ADCs at OUT0 SMA connector and 153.6 MHz for the FPGA at OUT8 SMA connector. Refer to the AD9516 documentation for more information on configuring the AD9516 clock module.
  10. Turn on the power for the Arria V SoC development board.

The hardware system is now ready for programming.

Level Two Title