Visible to Intel only — GUID: nik1410905703846
Ixiasoft
1. Datasheet
2. Getting Started with the SR-IOV Design Example
3. Parameter Settings
4. Physical Layout
5. Interfaces and Signal Descriptions
6. Registers
7. Reset and Clocks
8. Programming and Testing SR-IOV Bridge MSI Interrupts
9. Error Handling
10. IP Core Architecture
11. Design Implementation
12. Debugging
13. Document Revision History
A. Transaction Layer Packet (TLP) Header Formats
B. Arria® 10 Avalon-ST with SR-IOV Interface for PCIe Solutions User Guide Archive
3.1. Parameters
3.2. Arria® 10 Avalon-ST Settings
3.3. Arria® 10 SR-IOV System Settings
3.4. Base Address Register (BAR) Settings
3.5. SR-IOV Device Identification Registers
3.6. Arria® 10 Interrupt Capabilities
3.7. Physical Function TLP Processing Hints (TPH)
3.8. Address Translation Services (ATS)
3.9. PCI Express and PCI Capabilities Parameters
3.10. PHY Characteristics
3.11. Example Designs
5.1. Avalon-ST TX Interface
5.2. Component-Specific Avalon-ST Interface Signals
5.3. Avalon-ST RX Interface
5.4. BAR Hit Signals
5.5. Configuration Status Interface
5.6. Clock Signals
5.7. Function-Level Reset (FLR) Interface
5.8. SR-IOV Interrupt Interface
5.9. Configuration Extension Bus (CEB) Interface
5.10. Implementing MSI-X Interrupts
5.11. Control Shadow Interface
5.12. Local Management Interface (LMI) Signals
5.13. Reset, Status, and Link Training Signals
5.14. Hard IP Reconfiguration Interface
5.15. Serial Data Signals
5.16. Test Signals
5.17. PIPE Interface Signals
5.18. Arria® 10 Development Kit Conduit Interface
6.1. Addresses for Physical and Virtual Functions
6.2. Correspondence between Configuration Space Registers and the PCIe Specification
6.3. PCI and PCI Express Configuration Space Registers
6.4. MSI Registers
6.5. MSI-X Capability Structure
6.6. Power Management Capability Structure
6.7. PCI Express Capability Structure
6.8. Advanced Error Reporting (AER) Enhanced Capability Header Register
6.9. Uncorrectable Error Status Register
6.10. Uncorrectable Error Mask Register
6.11. Uncorrectable Error Severity Register
6.12. Correctable Error Status Register
6.13. Correctable Error Mask Register
6.14. Advanced Error Capabilities and Control Register
6.15. Header Log Registers 0-3
6.16. SR-IOV Virtualization Extended Capabilities Registers
6.17. Virtual Function Registers
6.16.1. SR-IOV Virtualization Extended Capabilities Registers Address Map
6.16.2. ARI Enhanced Capability Header
6.16.3. SR-IOV Enhanced Capability Registers
6.16.4. Initial VFs and Total VFs Registers
6.16.5. VF Device ID Register
6.16.6. Page Size Registers
6.16.7. VF Base Address Registers (BARs) 0-5
6.16.8. Secondary PCI Express Extended Capability Header
6.16.9. Lane Status Registers
6.16.10. Transaction Processing Hints (TPH) Requester Enhanced Capability Header
12.1.1. Changing Between Serial and PIPE Simulation
12.1.2. Using the PIPE Interface for Gen1 and Gen2 Variants
12.1.3. Viewing the Important PIPE Interface Signals
12.1.4. Disabling the Scrambler for Gen1 and Gen2 Simulations
12.1.5. Disabling 8B/10B Encoding and Decoding for Gen1 and Gen2 Simulations
Visible to Intel only — GUID: nik1410905703846
Ixiasoft
10.4.3. Interrupts
The Hard IP for PCI Express offers the following interrupt mechanisms:
- Message Signaled Interrupts (MSI)— MSI uses the TLP single dword memory writes to to implement interrupts. This interrupt mechanism conserves pins because it does not use separate wires for interrupts. In addition, the single dword provides flexibility in data presented in the interrupt message. The MSI Capability structure is stored in the Configuration Space and is programmed using Configuration Space accesses. MSI interrupts are only supported for Physical Functions.
- MSI-X—The Transaction Layer generates MSI-X messages which are single dword memory writes. The MSI-X Capability structure points to an MSI-X table structure and MSI-X PBA structure which are stored in memory. This scheme is in contrast to the MSI capability structure, which contains all of the control and status information for the interrupt vectors. MSI-X interrupts are supported for Physical and Virtual Functions.
- Legacy interrupts—The app_int_sts port controls legacy interrupt generation. When app_int_sts is asserted, the Hard IP generates an Assert_INT<n> message TLP.
- MSI interrupts are only supported for Physical Functions.