Quartus® Prime Pro Edition User Guide: Design Constraints

Download PDF
ID 683143
Date 8/07/2024
Public
Document Table of Contents
Document Table of Contents x
Answers to Top FAQs 1. Constraining Designs 2. Interface Planning 3. Managing Device I/O Pins 4. Quartus® Prime Pro Edition User Guide: Design Constraints Document Archives A. Quartus® Prime Pro Edition User Guides
1. Constraining Designs x
1.1. Specifying Design Constraints in the GUI 1.2. Constraining Designs with Tcl Scripts 1.3. A Fully Iterative Scripted Flow 1.4. Constraining Designs Revision History
1.1. Specifying Design Constraints in the GUI x
1.1.1. Global Constraints and Assignments 1.1.2. Node, Entity, and Instance-Level Constraints 1.1.3. Probing Between Components of the Quartus® Prime GUI 1.1.4. Specifying Timing Constraints
1.1.2. Node, Entity, and Instance-Level Constraints x
1.1.2.1. Specify Instance-Specific Constraints in Assignment Editor 1.1.2.2. Specify NoC Constraints in NoC Assignment Editor 1.1.2.3. Specify Dual Simplex Assignments in DS Assignment Editor 1.1.2.4. Specify I/O Constraints in Pin Planner 1.1.2.5. Plan Interface Constraints in Interface Planner and Tile Interface Planner 1.1.2.6. Adjust Constraints with the Chip Planner 1.1.2.7. Constraining Designs with the Design Partition Planner
1.1.2.1. Specify Instance-Specific Constraints in Assignment Editor x
1.1.2.1.1. Specifying Multi-Dimensional Bus Constraints
1.1.2.2. Specify NoC Constraints in NoC Assignment Editor x
1.1.2.2.1. NoC Assignment Editor Interface Controls 1.1.2.2.2. Troubleshooting NoC Assignment Editor
1.2. Constraining Designs with Tcl Scripts x
1.2.1. Create a Project and Apply Constraints 1.2.2. Assigning a Pin 1.2.3. Generating Quartus® Prime Settings Files 1.2.4. Synopsys* Design Constraint (.sdc) Files 1.2.5. Tcl-only Script Flows
2. Interface Planning x
2.1. Using Interface Planner 2.2. Using Tile Interface Planner 2.3. Interface Planning Revision History
2.1. Using Interface Planner x
2.1.1. Interface Planner User Interface 2.1.2. Interface Planner General Tool Flow 2.1.3. Interface Planner NoC Tool Flow 2.1.4. Interface Planner Reports
2.1.1. Interface Planner User Interface x
2.1.1.1. Flow Controls 2.1.1.2. Home Tab Controls 2.1.1.3. Assignments Tab Controls 2.1.1.4. Plan Tab Controls 2.1.1.5. Reports Tab Controls
2.1.2. Interface Planner General Tool Flow x
2.1.2.1. Step 1: Setup and Synthesize the Project 2.1.2.2. Step 2: Initialize Interface Planner 2.1.2.3. Step 3: Update Plan with Project Assignments 2.1.2.4. Step 4: Plan Periphery Placement 2.1.2.5. Step 5: Report Placement Data 2.1.2.6. Step 6: Validate and Export Plan Constraints
2.1.2.4. Step 4: Plan Periphery Placement x
2.1.2.4.1. Plan Clock Networks 2.1.2.4.2. Saving & Loading Floorplans
2.1.4. Interface Planner Reports x
2.1.4.1. Report Summary 2.1.4.2. Report Pins 2.1.4.3. Report HSSI Channels 2.1.4.4. Report Clocks 2.1.4.5. Report Periphery Locations 2.1.4.6. Report Cell Connectivity 2.1.4.7. Report Instance Assignments 2.1.4.8. Report NoC Performance
2.2. Using Tile Interface Planner x
2.2.1. Tile Interface Planner Terminology 2.2.2. Tile Interface Planner Tool Flow 2.2.3. Constraining Dynamic Reconfiguration IP 2.2.4. Tile Interface Planner GUI Reference
2.2.2. Tile Interface Planner Tool Flow x
2.2.2.1. Step 1: Instantiate IP and Run Design Analysis 2.2.2.2. Step 2: Initialize Tile Interface Planner 2.2.2.3. Step 3: Update Plan with Project Assignments 2.2.2.4. Step 4: Create a Tile Plan 2.2.2.5. Step 5: Save Tile Plan Assignments 2.2.2.6. Step 6: Run Logic Generation and Design Synthesis
2.2.2.4. Step 4: Create a Tile Plan x
2.2.2.4.1. Placing IP Components 2.2.2.4.2. Constraining IP Building Blocks
2.2.3. Constraining Dynamic Reconfiguration IP x
2.2.3.1. Defining a Dynamic Reconfiguration Group 2.2.3.2. Assigning Dynamic Reconfiguration Group Placement
2.2.4. Tile Interface Planner GUI Reference x
2.2.4.1. Flow Controls 2.2.4.2. Home Tab 2.2.4.3. Assignments Tab Controls 2.2.4.4. Plan Tab Controls 2.2.4.5. Tcl Console Window
2.2.4.4. Plan Tab Controls x
2.2.4.4.1. Design Tree and Filters 2.2.4.4.2. Reconfiguration Groups View 2.2.4.4.3. Legal Locations Pane
3. Managing Device I/O Pins x
3.1. I/O Planning Overview 3.2. Assigning I/O Pins 3.3. Importing and Exporting I/O Pin Assignments 3.4. Validating Pin Assignments 3.5. Verifying I/O Timing 3.6. Viewing Routing and Timing Delays 3.7. Scripting API 3.8. Managing Device I/O Pins Revision History
3.1. I/O Planning Overview x
3.1.1. Basic I/O Planning Flow 3.1.2. Integrating PCB Design Tools 3.1.3. Intel FPGA Device and I/O Terminology
3.2. Assigning I/O Pins x
3.2.1. Assigning to Exclusive Pin Groups 3.2.2. Assigning Slew Rate and Drive Strength 3.2.3. Assigning I/O Banks 3.2.4. Changing Pin Planner Highlight Colors 3.2.5. Showing I/O Lanes 3.2.6. Assigning Differential Pins 3.2.7. Entering Pin Assignments with Tcl Commands 3.2.8. Entering Pin Assignments in HDL Code
3.2.6. Assigning Differential Pins x
3.2.6.1. Overriding I/O Placement Rules on Differential Pins
3.2.8. Entering Pin Assignments in HDL Code x
3.2.8.1. Using Low-Level I/O Primitives
3.3. Importing and Exporting I/O Pin Assignments x
3.3.1. Importing and Exporting for PCB Tools 3.3.2. Migrating Assignments to Another Target Device
3.4. Validating Pin Assignments x
3.4.1. I/O Assignment Validation Rules 3.4.2. I/O Assignment Analysis 3.4.3. Understanding I/O Analysis Reports
3.4.2. I/O Assignment Analysis x
3.4.2.1. Early I/O Assignment Analysis Without Design Files 3.4.2.2. I/O Assignment Analysis With Design Files 3.4.2.3. Overriding Default I/O Pin Analysis
3.5. Verifying I/O Timing x
3.5.1. Running Advanced I/O Timing 3.5.2. Adjusting I/O Timing and Power with Capacitive Loading
3.5.1. Running Advanced I/O Timing x
3.5.1.1. Board Trace Models 3.5.1.2. Defining the Board Trace Model 3.5.1.3. Modifying the Board Trace Model 3.5.1.4. Specifying Near-End vs Far-End I/O Timing Analysis 3.5.1.5. Advanced I/O Timing Analysis Reports
3.7. Scripting API x
3.7.1. Generate Mapped Netlist 3.7.2. Reserve Pins 3.7.3. Set Location 3.7.4. Exclusive I/O Group 3.7.5. Slew Rate and Current Strength
Answers to Top FAQs
1. Constraining Designs
2. Interface Planning
3. Managing Device I/O Pins
4. Quartus® Prime Pro Edition User Guide: Design Constraints Document Archives
A. Quartus® Prime Pro Edition User Guides

2.1.2.4. Step 4: Plan Periphery Placement

Click Plan Design on the Flow control to interactively place IP cores and other design elements in legal locations in the device periphery. The Plan tab displays a list of your project's design elements, alongside a graphical abstraction of the target device architecture.

For efficiency, place design elements in the following order in Interface Planner:

  1. Place all I/O pins or elements, such as PLLs, that have known, specific location requirements.
  2. Place all known periphery interface IP.
  3. (Optional) Place all remaining unplaced cells.

Use the following controls to place design elements in the Interface Planner floorplan:

  1. Locate design elements that you want to place in the Design Element list. You can search and filter the list by name, IP, placement status, I/Os, and other criteria.
  2. To customize design element color coding definitions, click the Highlight column.
    Figure 20.  Interface Planner (Plan Tab)
  3. Use any of the following methods to place design elements in the floorplan:
    • Drag elements from the Design Elements list and drop them onto available device resources in the Chip or Package view. Use Ctrl+Click to drag and pan across the Chip or Package views. You may experience a small delay while dragging as Interface Planner calculates the legal locations.
    • To allow Interface Planner to place an unplaced design element in a legal location, right-click and select Autoplace Selected. You must use Autoplace Selected for all unplaced clocks .
    • Click the button next to the Design Elements to display a list of Legal Locations. Click any legal location in the list to highlight the location in the floorplan. Double-click any location in the list to place the element in the location.
    Figure 21. Listing Legal Locations
  4. To step forward and backward though your plan changes, click the Undo and Redo buttons.
  5. To visualize and traverse design connectivity (for example, to view the reference clock pin and driven destination cells of a PLL), select any design element and then click the Link Info tab. Click the Back and Forward buttons to traverse design connectivity.
  6. To generate a report that shows the placement locations the Fitter prefers, select a design element and click Report Placeability of Selected Element.
Figure 22. Link Info Tab for Traversing Connectivity
Note: Changes made in Interface Planner do not apply to your Quartus® Prime project until you apply the generated interface plan constraints script to your project.

Section Content
Plan Clock Networks
Saving & Loading Floorplans

Related Information
Level Two Title