Embedded Memory User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813901
Date 11/04/2024
Public
Document Table of Contents
Document Table of Contents x
1. Agilex™ 5 Embedded Memory Overview 2. Agilex™ 5 Embedded Memory Architecture and Features 3. Agilex™ 5 Embedded Memory Design Considerations 4. Agilex™ 5 Embedded Memory IP References 5. Agilex™ 5 Embedded Memory Debugging 6. Embedded Memory User Guide: Agilex™ 5 FPGAs and SoCs Archives 7. Document Revision History for the Embedded Memory User Guide: Agilex™ 5 FPGAs and SoCs
1. Agilex™ 5 Embedded Memory Overview x
1.1. Agilex™ 5 Embedded Memory Features 1.2. Agilex™ 5 Embedded Memory Block Signals
2. Agilex™ 5 Embedded Memory Architecture and Features x
2.1. Byte Enable in Agilex™ 5 Embedded Memory Blocks 2.2. Address Hold Support 2.3. Asynchronous Clear and Synchronous Clear 2.4. Memory Blocks Error Correction Code (ECC) Support 2.5. Agilex™ 5 Embedded Memory Clocking Modes 2.6. Agilex™ 5 Embedded Memory Configurations 2.7. Force-to-Zero 2.8. Coherent Read Memory 2.9. Freeze Logic 2.10. True Dual Port Dual Clock Emulator 2.11. Initial Value of Read and Write Address Registers 2.12. Timing/Power Optimization Feature in M20K Blocks
2.1. Byte Enable in Agilex™ 5 Embedded Memory Blocks x
2.1.1. Byte Enable Controls 2.1.2. Data Byte Output 2.1.3. Byte Enable Behavior
2.4. Memory Blocks Error Correction Code (ECC) Support x
2.4.1. Error Correction Code Truth Table 2.4.2. Parity Bit 2.4.3. ECC Parity Flip 2.4.4. ECC Read-During-Write Behavior
2.5. Agilex™ 5 Embedded Memory Clocking Modes x
2.5.1. Single Clock Mode 2.5.2. Read/Write Clock Mode 2.5.3. Input/Output Clock Mode 2.5.4. Asynchronous/Synchronous Clears in Clocking Modes 2.5.5. Output Read Data in Simultaneous Read/Write 2.5.6. Independent Clock Enables in Clocking Modes
2.6. Agilex™ 5 Embedded Memory Configurations x
2.6.1. Mixed-Width Port Configurations
2.8. Coherent Read Memory x
2.8.1. Forwarding Logic
2.10. True Dual Port Dual Clock Emulator x
2.10.1. True Dual-Port Mixed Port Read During Write New Data Emulation
3. Agilex™ 5 Embedded Memory Design Considerations x
3.1. Consider the Memory Block Selection 3.2. Consider the Concurrent Write Behavior 3.3. Read-During-Write (RDW) 3.4. Consider Power-Up State and Memory Initialization 3.5. Reduce Power Consumption 3.6. Avoid Providing Non-Deterministic Input 3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously 3.8. Advanced Settings in Quartus® Prime Software for Memory 3.9. Consider the Memory Depth Setting 3.10. Consider Registering the Memory Output
3.3. Read-During-Write (RDW) x
3.3.1. Customize Read-During-Write Behavior
3.3.1. Customize Read-During-Write Behavior x
3.3.1.1. Same-Port Read-During-Write Mode 3.3.1.2. Mixed-Port Read-During-Write Mode 3.3.1.3. Read-During-Write Data Output and Memory Location Behaviors
4. Agilex™ 5 Embedded Memory IP References x
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores 4.2. FIFO Intel® FPGA IP 4.3. Shift Register (RAM-based) Intel® FPGA IP
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores x
4.1.1. Release Information for RAM and ROM Intel® FPGA IPs 4.1.2. RAM: 1-PORT Intel® FPGA IP Parameters 4.1.3. RAM: 2-PORT Intel® FPGA IP Parameters 4.1.4. RAM: 4-PORT Intel® FPGA IP Parameters 4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters 4.1.6. ROM: 2-PORT Intel® FPGA IP Parameters 4.1.7. Changing Parameter Settings Manually 4.1.8. RAM and ROM Interface Signals
4.1.7. Changing Parameter Settings Manually x
4.1.7.1. RAM and ROM Parameter Settings
4.2. FIFO Intel® FPGA IP x
4.2.1. Release Information for FIFO Intel® FPGA IP 4.2.2. Configuration Methods 4.2.3. Specifications 4.2.4. FIFO Functional Timing Requirements 4.2.5. SCFIFO ALMOST_EMPTY Functional Timing 4.2.6. FIFO Output Status Flag and Latency 4.2.7. FIFO Metastability Protection and Related Options 4.2.8. FIFO Synchronous Clear and Asynchronous Clear Effect 4.2.9. SCFIFO and DCFIFO Show-Ahead Mode 4.2.10. Different Input and Output Width 4.2.11. DCFIFO Timing Constraint Setting 4.2.12. Coding Example for Manual Instantiation 4.2.13. Instantiation Template 4.2.14. Design Example 4.2.15. Gray-Code Counter Transfer at the Clock Domain Crossing 4.2.16. Guidelines for Embedded Memory ECC Feature 4.2.17. FIFO Intel® FPGA IP Parameters 4.2.18. Reset Scheme
4.2.3. Specifications x
4.2.3.1. Verilog HDL Prototype 4.2.3.2. VHDL Component Declaration 4.2.3.3. VHDL LIBRARY-USE Declaration 4.2.3.4. HDL Code from Parameterizable Macros Template 4.2.3.5. FIFO Signals 4.2.3.6. FIFO Parameter Settings
4.2.8. FIFO Synchronous Clear and Asynchronous Clear Effect x
4.2.8.1. Recovery and Removal Timing Violation Warnings when Compiling a DCFIFO
4.2.11. DCFIFO Timing Constraint Setting x
4.2.11.1. Embedded Timing Constraint 4.2.11.2. User Configurable Timing Constraint
4.2.11.2. User Configurable Timing Constraint x
4.2.11.2.1. SDC Commands
4.3. Shift Register (RAM-based) Intel® FPGA IP x
4.3.1. Release Information for Shift Register (RAM-based) Intel® FPGA IP 4.3.2. Shift Register (RAM-based) Intel® FPGA IP Features 4.3.3. Shift Register (RAM-based) Intel® FPGA IP General Description 4.3.4. Shift Register (RAM-based) Intel® FPGA IP Parameter Settings 4.3.5. Shift Register Ports and Parameters Setting
1. Agilex™ 5 Embedded Memory Overview
2. Agilex™ 5 Embedded Memory Architecture and Features
3. Agilex™ 5 Embedded Memory Design Considerations
4. Agilex™ 5 Embedded Memory IP References
5. Agilex™ 5 Embedded Memory Debugging
6. Embedded Memory User Guide: Agilex™ 5 FPGAs and SoCs Archives
7. Document Revision History for the Embedded Memory User Guide: Agilex™ 5 FPGAs and SoCs

4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters

This table lists the parameters for the ROM: 1-PORT Intel® FPGA IP.
Table 27.  ROM: 1-PORT Intel® FPGA IP Parameter Settings
Parameter Legal Values Description
Parameter Settings: General Page
How wide should the ‘q’ output bus be? — Specifies the width of the ‘q’ output bus.
How many words of memory? — Specifies the number of words.
What should the memory block type be? Auto, MLAB, M20K Specifies the memory block type. The types of memory block that are available for selection depends on your target device.
Set the maximum block depth to
  • MLAB: Auto, 32
  • M20K: Auto, 512, 1024, 2048
Specifies the maximum block depth in words.
Which clocking method would you like to use?
  • Single clock
  • Dual clock: use separate ‘input’ and ‘output’ clocks

Specifies the clocking method to use.

  • Single clock—A single clock and a clock enable controls all registers of the memory block
  • Dual clock: use separate ‘input’ and ‘output’ clocks—The input clock controls the address registers and the output clock controls the data-out registers. There are no write-enable, byte-enable, or data-in registers in ROM mode.
Parameter Settings: Regs/Clken/Aclrs
Which ports should be registered?
The following options are available:
  • ‘address’ input port
  • ‘q’ output port
 On/Off Specifies whether to register the input and output ports.
Use clock enable for port A input registers On/Off Specifies whether to use clock enable for port A input registers.
Use clock enable for port A output registers On/Off Specifies whether to use clock enable for port A output registers.
Create an ‘addressstall_a’ input port On/Off Specifies whether to create an addressstall_a input port. You can create this port to act as an extra active low clock enable input for the address registers.
Create an ‘aclr’ asynchronous clear for the registered ports.

The following options are available:

  • ‘address’ port
  • ‘q’ port
 On/Off Specifies whether the registered ports be affected by an asynchronous clear port.
Create a ‘sclr’ asynchronous clear for the registered ports.
  • ‘q’ port
 On/Off Specifies whether the q port be affected by a synchronous clear port.
Create an ‘rden’ read enable signal On/Off Specifies whether to create a read enable signal.
Parameter Settings: Mem Init
Do you want to specify the initial content of the memory?
  • No, leave it blank
  • Yes, use this file for the memory content data

Specifies the initial content of the memory.

In ROM mode, you must specify a memory initialization file (.mif) or a hexadecimal (Altera-format) file (.hex). The Yes, use this file for the memory content data option is turned on by default.
Parameter Settings: Performance Optimization
Enable Force-to-Zero On/Off Specifies whether to set the output to zero when you deassert the read enable signal.

Enabling this feature helps improve the glue logic performance when the selected memory depth is larger than a single memory block.

Which timing/power optimization option do you want to use?
  • Auto
  • High Speed
  • Low Power
Specifies the timing/power optimization option to use. This option is only applicable when you select M20K memory type on Agilex™ 5 devices.
Level Two Title