Hard Processor System Component Reference Manual: Agilex™ 5 SoCs

Download PDF
ID 813752
Date 8/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction to the Agilex™ 5 Hard Processor System Component 2. Configuring the Agilex™ 5 Hard Processor System Component 3. Simulating the Agilex™ 5 HPS Component 4. Design Guidelines 5. HPS EMIF Platform Designer Example Designs 6. Document Revision History for the Hard Processor System Component Reference Manual Agilex™ 5 SoCs
1. Introduction to the Agilex™ 5 Hard Processor System Component x
1.1. Micro Processor Unit 1.2. Application Processor Subsystem 1.3. Peripheral Subsystem 1.4. CoreSight* Debug Components 1.5. Interconnect 1.6. FPGA Bridges 1.7. Introduction to the Agilex™ 5 Hard Processor System Component Revision History
2. Configuring the Agilex™ 5 Hard Processor System Component x
2.1. Parameterizing the HPS Component 2.2. HPS-FPGA Interfaces 2.3. SDRAM 2.4. HPS Clocks, Reset, Power 2.5. I/O Delays 2.6. Pin Mux and Peripherals 2.7. Generating and Compiling the HPS Component 2.8. Using the Address Span Extender Component 2.9. Configuring the Agilex™ 5 Hard Processor System Component Revision History
2.2. HPS-FPGA Interfaces x
2.2.1. General 2.2.2. HPS FPGA Bridges 2.2.3. DMA Controller Interface 2.2.4. Interrupts
2.2.1. General x
2.2.1.1. Enable MPU Standby and Event Signals 2.2.1.2. Enable General Purpose Signals 2.2.1.3. Enable Debug APB* Interface 2.2.1.4. Enable System Trace Macrocell (STM) Hardware Events 2.2.1.5. Enable SWJ-DP JTAG Interface 2.2.1.6. Enable FPGA Cross Trigger Interface 2.2.1.7. Enable AMBA* Trace Bus (ATB)
2.2.2. HPS FPGA Bridges x
2.2.2.1. FPGA to HPS Subordinate 2.2.2.2. FPGA to SDRAM Subordinate 2.2.2.3. HPS to FPGA Manager 2.2.2.4. Lightweight HPS to FPGA Manager
2.2.4. Interrupts x
2.2.4.1. FPGA-to-HPS 2.2.4.2. HPS-to-FPGA
2.3. SDRAM x
2.3.1. EMIF Interface
2.4. HPS Clocks, Reset, Power x
2.4.1. Input Clocks 2.4.2. PLL Clocks 2.4.3. Power and Resets
2.4.1. Input Clocks x
2.4.1.1. External Clocks 2.4.1.2. FPGA-to-HPS Clocks 2.4.1.3. Peripheral FPGA Clocks
2.4.2. PLL Clocks x
2.4.2.1. Main PLL Output 2.4.2.2. Peripheral PLL Output 2.4.2.3. MPU Clocks 2.4.2.4. NOC Clocks 2.4.2.5. Peripheral Clocks 2.4.2.6. HPS-to-FPGA User Clocks
2.4.3. Power and Resets x
2.4.3.1. Power Configurations 2.4.3.2. Reset Signals
2.6. Pin Mux and Peripherals x
2.6.1. Pin Mux GUI 2.6.2. EMAC PTP Interface 2.6.3. HPS I/O Open Drain 2.6.4. HPS I/O Locations
2.6.1. Pin Mux GUI x
2.6.1.1. Auto-Place IP 2.6.1.2. Advanced
2.6.1.1. Auto-Place IP x
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC x
2.6.1.1.1.1. HPS IO Placement Priority
2.6.1.2. Advanced x
2.6.1.2.1. Advanced IP Placement 2.6.1.2.2. Advanced FPGA Placement
3. Simulating the Agilex™ 5 HPS Component x
3.1. Simulation Flows 3.2. Running the Simulation of the Design Examples 3.3. Clock and Reset Interface 3.4. FPGA-to-HPS AXI* Subordinate Interface 3.5. FPGA-to-SDRAM AXI* Subordinate Interface 3.6. HPS-to-FPGA AXI* Initiator Interface 3.7. Lightweight HPS-to-FPGA AXI* Initiator Interface 3.8. Simulating the Agilex™ 5 HPS Component Revision History
3.1. Simulation Flows x
3.1.1. Setting Up the HPS Component for Simulation 3.1.2. Generating the HPS Simulation Model in Platform Designer 3.1.3. RTL Simulation Setup Scripts
3.1.3. RTL Simulation Setup Scripts x
3.1.3.1. QuestaSim* Simulation Steps 3.1.3.2. Cadence® Xcelium* Simulation Steps 3.1.3.3. Synopsys* VCS* Simulation Steps 3.1.3.4. Synopsys* VCS* MX Simulation Steps 3.1.3.5. Aldec® Riviera-PRO* Simulation Steps
3.2. Running the Simulation of the Design Examples x
3.2.1. HPS-to-FPGA Bridge (H2F) 3.2.2. Lightweight HPS-to-FPGA (LWH2F) 3.2.3. FPGA-to-HPS Bridge (F2H) 3.2.4. FPGA-to-SDRAM Bridge (F2SDRAM)
3.2.1. HPS-to-FPGA Bridge (H2F) x
3.2.1.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.1.2. Steps to run the Simulation in Synopsys* VCS*
3.2.2. Lightweight HPS-to-FPGA (LWH2F) x
3.2.2.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.2.2. Steps to run the Simulation in Synopsys* VCS*
3.2.3. FPGA-to-HPS Bridge (F2H) x
3.2.3.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.3.2. Steps to run the Simulation in Synopsys* VCS*
3.2.4. FPGA-to-SDRAM Bridge (F2SDRAM) x
3.2.4.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.4.2. Steps to run the Simulation in Synopsys* VCS*
3.3. Clock and Reset Interface x
3.3.1. Clock Interface 3.3.2. Reset Interface
4. Design Guidelines x
4.1. HPS System Reset Considerations 4.2. Design Guidelines Revision History
5. HPS EMIF Platform Designer Example Designs x
5.1. Terminology 5.2. Block Diagram 5.3. Version Support 5.4. Download Example Design Files 5.5. HPS EMIF Platform Designer Example Designs 5.6. Specific Examples 5.7. General Connection Guideline 5.8. Supported Memory Protocols Differences Among Intel SoC Device Families 5.9. IO96 Bank and Lane Usage for HPS EMIF 5.10. Quartus Report of I/O Bank Usage
5.6. Specific Examples x
5.6.1. DDR4 Examples 5.6.2. LPDDR4 Examples 5.6.3. LPDDR5 Examples
1. Introduction to the Agilex™ 5 Hard Processor System Component
2. Configuring the Agilex™ 5 Hard Processor System Component
3. Simulating the Agilex™ 5 HPS Component
4. Design Guidelines
5. HPS EMIF Platform Designer Example Designs
6. Document Revision History for the Hard Processor System Component Reference Manual Agilex™ 5 SoCs

2.4.1.3. Peripheral FPGA Clocks

Table 9.  Peripheral FPGA Clocks Description
Parameter Name Parameter Description

EMAC 0 (emac0_md_clk clock frequency)

If EMAC 0 peripheral is routed to FPGA, use the input field to specify EMAC 0 MDIO clock frequency.

EMAC 0 (emac0_gtx_clk clock frequency)

If EMAC 0 peripheral is routed to FPGA, use the input field to specify EMAC 0 transmit clock frequency.

EMAC 1 (emac1_md_clk clock frequency)

If EMAC 1 peripheral is routed to FPGA, use the input field to specify EMAC 1 MDIO clock frequency.

EMAC 1 (emac1_gtx_clk clock frequency)

If EMAC 1 peripheral is routed to FPGA, use the input field to specify EMAC 1 transmit clock frequency.

EMAC 2 (emac2_md_clk clock frequency)

If EMAC 2 peripheral is routed to FPGA, use the input field to specify EMAC 2 MDIO clock frequency.

EMAC 2 (emac2_gtx_clk clock frequency)

If EMAC 2 peripheral is routed to FPGA, use the input field to specify EMAC 2 transmit clock frequency.

SPIM 0 (spim0_sclk_out clock frequency)

If SPI initiator 0 peripheral is routed to FPGA, use the input field to specify SPI initiator 0 output clock frequency.

SPIM 1 (spim1_sclk_out clock frequency)

If SPI initiator 1 peripheral is routed to FPGA, use the input field to specify SPI initiator 1 output clock frequency.

I2C0 (i2c0_clk clock frequency)

If I2C 0 peripheral is routed to FPGA, use the input field to specify I2C 0 output clock frequency.

I2C1 (i2c1_clk clock frequency)

If I2C 1 peripheral is routed to FPGA, use the input field to specify I2C 1 output clock frequency.

I3C0 (i3c_0_scl_oe clock frequency)

If I3C0 peripheral is routed to FPGA, use the input field to specify I3C0 clock frequency.

I3C1 (i3c_1_scl_oe clock frequency)

If I3C1 peripheral is routed to FPGA, use the input field to specify I3C1 clock frequency.

I2CEMAC0 (i2cemac0_clk)

If this peripheral pin multiplexing is configured to route to the FPGA fabric, use the input field to specify the I2CEMAC0i2cemac0_clk clock frequency.

I2CEMAC1 (i2cemac1_clk)

If this peripheral pin multiplexing is configured to route to the FPGA fabric, use the input field to specify the I2CEMAC1i2cemac1_clk clock frequency.

I2CEMAC2 (i2cemac2_clk)

If this peripheral pin multiplexing is configured to route to the FPGA fabric, use the input field to specify the I2CEMAC2i2cemac2_clk clock frequency.

Level Two Title