Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813652
Date 11/25/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 40G Ethernet Intel® FPGA IP 2. Low Latency 40G Ethernet Intel® FPGA IP Parameters 3. Getting Started 4. Functional Description 5. Clocking and Reset Requirements 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Comparison Between Various Low Latency 40G Ethernet Intel® FPGA IPs 9. Document Revision History for the Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs
1. About the Low Latency 40G Ethernet Intel® FPGA IP x
1.1. Low Latency 40G Ethernet Intel® FPGA IP Supported Features 1.2. Low Latency 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support 1.3. Resource Utilization 1.4. Release Information
1.2. Low Latency 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support x
1.2.1. Low Latency 40G Ethernet Intel® FPGA IP Device Family Support 1.2.2. Low Latency 40G Ethernet Intel® FPGA IP Device Speed Grade Support
3. Getting Started x
3.1. Introduction to Intel® FPGA IP 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Parameters and Options 3.4. Simulating the IP 3.5. Generated File Structure 3.6. Integrating Your IP in Your Design 3.7. Testbench 3.8. Compiling the Full Design and Programming the FPGA
3.6. Integrating Your IP in Your Design x
3.6.1. Pin Assignments 3.6.2. Placement Settings
3.7. Testbench x
3.7.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency 40G Ethernet Intel® FPGA IP Functional Description 4.2. GTS Transceiver Configuration 4.3. TX Datapath 4.4. RX Datapath 4.5. Flow Control 4.6. Link Fault Signaling Interface
4.3. TX Datapath x
4.3.1. TX MAC 4.3.2. TX PCS 4.3.3. PMA
4.3.1. TX MAC x
4.3.1.1. Preamble Insertion 4.3.1.2. Frame Padding 4.3.1.3. Inter-Packet Gap Generation and Insertion 4.3.1.4. Frame Check Sequence (CRC-32) Insertion 4.3.1.5. TX Avalon® Streaming Filter
4.4. RX Datapath x
4.4.1. RX MAC 4.4.2. RX PCS
4.4.1. RX MAC x
4.4.1.1. IP Core Preamble Processing 4.4.1.2. IP Core CRC Checking and Dynamic Forwarding 4.4.1.3. IP Core Strict SFD Checking 4.4.1.4. Length/Type Field Processing
4.4.1.4. Length/Type Field Processing x
4.4.1.4.1. Frame Type Checking 4.4.1.4.2. Length Checking
4.5. Flow Control x
4.5.1. TX Pause/PFC Flow Control Transmission 4.5.2. XON/XOFF Pause Frames
5. Clocking and Reset Requirements x
5.1. Clocks 5.2. Reset Requirements
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. TX PCS Interface to User Logic 6.4. RX PCS Interface to User Logic 6.5. GTS Transceivers Signals 6.6. GTS Transceiver Reconfiguration Signals 6.7. Avalon® Memory-Mapped Management Interface 6.8. Miscellaneous Status and Debug Signals 6.9. Reset Signals 6.10. Clocks 6.11. Flow Control Interface 6.12. GTS Reset Sequencer Intel® FPGA IP
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers 7.4. Pause/PFC Flow Control 7.5. Statistics Counters 7.6. Shadow Register
1. About the Low Latency 40G Ethernet Intel® FPGA IP
2. Low Latency 40G Ethernet Intel® FPGA IP Parameters
3. Getting Started
4. Functional Description
5. Clocking and Reset Requirements
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Comparison Between Various Low Latency 40G Ethernet Intel® FPGA IPs
9. Document Revision History for the Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs

4.2. GTS Transceiver Configuration

The GTS transceiver in the IP is configured in PCS Direct (PCS66) mode. For more details, refer to GTS Transceiver PHY User Guide .

The GTS transceivers are equipped with the following clock networks:
  • Reference clock
  • Core interface clock

You can configure the reference clock for the PMA via the IP GUI option.

Related Information
Level Two Title