Intel® Simics® Simulator for Intel® FPGAs: Agilex™ 5 Virtual Platform User Guide

Download PDF
ID 786901
Date 11/16/2024
Public
Document Table of Contents
Document Table of Contents x
1. About This Document 2. Agilex™ 5 Intel® Simics® Virtual Platforms 3. Agilex™ 5 Universal Virtual Platform Component Intel® Simics® Models 4. Running a Simulation with the Agilex™ 5 HPS Model 5. Supported Use Cases 6. Troubleshooting Issues When Migrating Software from Intel® Simics® to Hardware A. Document Revision History for Intel Simics Simulator for Intel FPGAs Agilex 5 Virtual Platform User Guide
1. About This Document x
1.1. Terminology 1.2. List of Acronyms
2. Agilex™ 5 Intel® Simics® Virtual Platforms x
2.1. Agilex™ 5 Universal Virtual Platform
2.1. Agilex™ 5 Universal Virtual Platform x
2.1.1. Agilex™ 5 Universal Virtual Platform Overview 2.1.2. Agilex™ 5 Universal Virtual Platform User-Configurable Parameters 2.1.3. Agilex™ 5 Universal Virtual Platform Key Capabilities
2.1.1. Agilex™ 5 Universal Virtual Platform Overview x
2.1.1.1. Agilex™ 5 HPS Component 2.1.1.2. HPS Subsystem Component 2.1.1.3. FPGA Fabric Design 2.1.1.4. qsys_top Component 2.1.1.5. FPGA Component 2.1.1.6. Board Component 2.1.1.7. System Component 2.1.1.8. Target Script
2.1.3. Agilex™ 5 Universal Virtual Platform Key Capabilities x
2.1.3.1. Boot-To-Operating System Prompt 2.1.3.2. Basic Ethernet 2.1.3.3. CPU Power-On and Boot Core Selection 2.1.3.4. Reset Flow 2.1.3.5. General Purpose I/O (GPIO) Loopback 2.1.3.6. USB Disks Hot-Plug Support 2.1.3.7. On-Chip Memory IP FPGA Fabric Example Design 2.1.3.8. FPGA-to-HPS Bridges 2.1.3.9. Exercising Peripheral Subsystem in FPGA Fabric Design 2.1.3.10. USB Controller Host/Device Mode Configuration 2.1.3.11. Agilex™ 5 HPS Component and Stepping Silicon Features Selection
3. Agilex™ 5 Universal Virtual Platform Component Intel® Simics® Models x
3.1. Agilex™ 5 HPS Intel® Simics® Model 3.2. Virtual Platform HPS Subsystem Components 3.3. Virtual Platform qsys_top Components 3.4. Virtual Platform Board Components 3.5. Modeling Support Limitations
3.1. Agilex™ 5 HPS Intel® Simics® Model x
3.1.1. Agilex™ 5 HPS Intel® Simics® Model Architecture 3.1.2. PSS Subsystem Components 3.1.3. MPU and APS Subsystem 3.1.4. MPFE Subsystem 3.1.5. Additional Agilex™ 5 HPS Components 3.1.6. Agilex™ 5 B0 Features Support
3.2. Virtual Platform HPS Subsystem Components x
3.2.1. External Memory Interface (EMIF) 3.2.2. Security Device Manager (SDM)
3.3. Virtual Platform qsys_top Components x
3.3.1. FPGA Fabric
3.4. Virtual Platform Board Components x
3.4.1. Marvel EMAC PHY 3.4.2. SD Card Device 3.4.3. ONFI NAND Memory Device 3.4.4. SPI Flash Device 3.4.5. AT24Cxx EEPROM Device 3.4.6. I3C Device 3.4.7. USB Disk Device 3.4.8. Intel® Simics® Text Console
4. Running a Simulation with the Agilex™ 5 HPS Model x
4.1. Prerequisites 4.2. Intel® Simics® Simulation Setup for the Agilex™ 5 Device 4.3. Starting the Simulation 4.4. Getting Device Information from the Intel® Simics® Model
1. About This Document
2. Agilex™ 5 Intel® Simics® Virtual Platforms
3. Agilex™ 5 Universal Virtual Platform Component Intel® Simics® Models
4. Running a Simulation with the Agilex™ 5 HPS Model
5. Supported Use Cases
6. Troubleshooting Issues When Migrating Software from Intel® Simics® to Hardware
A. Document Revision History for Intel Simics Simulator for Intel FPGAs Agilex 5 Virtual Platform User Guide

3.4.7. USB Disk Device

This device corresponds to a model of a generic USB Mass Storage device. There are two classes of USB disk devices supported as board devices (both are USB 3.1 Gen 1 and USB 2.0 compatible and can be connected to a USB 2.0 or USB 3.0 port):

  • High-Speed USB disk: USB 2.0 ports natively support this disk. However, USB 3.0 ports also support it.

    Component: usb3_disk_hs_comp

  • SuperSpeed USB disk: USB 3.0 ports natively support this disk. However, USB 2.0 ports also support it. Hence, the disk is backwards-compatible with USB 2.0 standard.

    Component: usb3_disk_comp

Both USB disks can be configured with a size limited to 64 TB, although the actual disk size is taken from the assigned image. The image to be loaded into the disk must be provided as part of the parameters defined in the virtual platform target script. The Intel® Simics® model of the devices implements a simple SCSI controller and supports control and bulk transfers. The model supports the hot-plug feature. Use the following Intel® Simics® commands to handle USB device operations:

Table 27.   Intel® Simics® Commands to Handle USB Device Operations
Command Parameter Purpose
load-file

file

Command for assigning an image file to the USB disk.
plug

port

Command for plugging in the USB device to specified port.

  • USB SuperSpeed (USB-SS) device could be plugged in a usb2 or usb3 port.
  • USB High Speed (USB-HS) devices could be plugged in a usb2 or usb3 port.
unplug

-

Command for unplugging a USB device.
<usb disk hierarchy>.usb_device->usb_host

-

 Command to determine if a USB disk is connected to a port. If nothing is returned, it means that the disk is not connected.
Level Two Title