Ethernet Subsystem Intel® FPGA IP User Guide

Download PDF
ID 773413
Date 11/04/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Feature Description 3. Ethernet Subsystem Parameters 4. Subsystem IP Blocks 5. Interfaces and Signals 6. Recommended Clock Connections 7. Register Descriptions 8. Ethernet SS IP Example Design 9. Document Revision History for the Ethernet Subsystem Intel FPGA IP User Guide
1. Introduction x
1.1. Supported Features 1.2. Device Family Support 1.3. Release Information 1.4. Resource Utilization 1.5. Getting Started
2. Feature Description x
2.1. Ethernet Subsystem Intel FPGA IP Overview 2.2. Supported Features
3. Ethernet Subsystem Parameters x
3.1. Parameter Editor Parameters 3.2. E-Tile Port Enablement Guidelines and Restrictions 3.3. F-Tile Ethernet Port to PMA Channel Mapping 3.4. Analog Parameter Options
4. Subsystem IP Blocks x
4.1. AXI Stream Bridge 4.2. CSR Address Decoder 4.3. Subsystem Abstraction Layer (SAL) 4.4. Dynamic Reconfiguration Extension Subsystem 4.5. IEEE 1588v2 PTP 4.6. Auto-Negotation and Link Training 4.7. Priority Flow Control
4.3. Subsystem Abstraction Layer (SAL) x
4.3.1. Subsystem Abstraction Layer (SAL) Commands
4.3.1. Subsystem Abstraction Layer (SAL) Commands x
4.3.1.1. NOP(0x0) 4.3.1.2. get_hssi_profile for E-Tile 4.3.1.3. get_hssi_profile for F-Tile 4.3.1.4. set_hssi_profile for E-Tile 4.3.1.5. set_hssi_profile for F-Tile 4.3.1.6. read_MAC_statistic 4.3.1.7. get_mtu 4.3.1.8. set_csr for E-Tile 4.3.1.9. set_csr for F-Tile 4.3.1.10. get_csr for E-Tile 4.3.1.11. get_csr for F-Tile 4.3.1.12. enable_loopback for E-Tile 4.3.1.13. enable_loopback for F-Tile 4.3.1.14. disable_loopback for E-Tile 4.3.1.15. disable_loopback for F-Tile 4.3.1.16. Reset MAC Statistics 4.3.1.17. set_mtu for F-Tile 4.3.1.18. Ncsi_get_link_status 4.3.1.19. Reserved 4.3.1.20. firmware_version (0xFF)
4.5. IEEE 1588v2 PTP x
4.5.1. TX PTP Classifier
5. Interfaces and Signals x
5.1. AXI4 Interfaces 5.2. Serial Interface 5.3. Clocks 5.4. Resets
5.1. AXI4 Interfaces x
5.1.1. AXI-Lite CSR 5.1.2. AXI-ST Client Interface 5.1.3. AXI-ST PHY Direct 5.1.4. AXI-ST PTP 5.1.5. Flow Control
6. Recommended Clock Connections x
6.1. Driving Multiple Ports with the Same Clock 6.2. Clock Connections for MAC Asynchronous Client FIFO 6.3. F-Tile Clock Connections for PTP Synchronous and Asynchronous cases 6.4. Clock Connections for SyncE Operation on E-Tile 6.5. Clock Connections for SyncE Operation on F-Tile 6.6. F-Tile PMA and FEC Direct PHY IP Clock Output
7. Register Descriptions x
7.1. Subsystem Registers 7.2. Port Registers 7.3. F-Tile Address Maps 7.4. F-Tile ANLT Port Register Map 7.5. F-Tile PTP Tile Adapter Register Map 7.6. F-Tile DR Controller Register Map
7.1. Subsystem Registers x
7.1.1. Device Feature Header Lo 7.1.2. Device Feature Header Hi 7.1.3. Feature GUID_L 7.1.4. Feature GUID_H 7.1.5. Feature CSR ADDR 7.1.6. Feature CSR Size Group 7.1.7. Version 7.1.8. Feature List 7.1.9. Interface Attribute Port X Parameters 7.1.10. HSSI Command/Status 7.1.11. HSSI Control/Address 7.1.12. HSSI Read Data 7.1.13. HSSI Write Data 7.1.14. HSSI Ethernet Port X Status 7.1.15. Priority Flow Control 7.1.16. Priority Flow Control TX Queue Statistics 7.1.17. Priority Flow Control RX Queue Statistics 7.1.18. Priority Flow Control TX Queue Threshold 7.1.19. Priority Flow Control RX Queue Threshold 7.1.20. F-Tile DR Controller Status 7.1.21. HSSI Hotplug Debug Port Control 7.1.22. HSSI Hotplug Debug Port Status
7.2. Port Registers x
7.2.1. PTP Packet Classifier Registers
7.2.1. PTP Packet Classifier Registers x
7.2.1.1. Recognized and Unrecognized Packet Counters 7.2.1.2. Parse Graph Specific Packet Counters
8. Ethernet SS IP Example Design x
8.1. Steps to Generate the Example Design 8.2. Supported Simulators 8.3. Running the Simulation Tests 8.4. Running the Hardware Tests
8.3. Running the Simulation Tests x
8.3.1. Steps to Simulate the Design Example
8.4. Running the Hardware Tests x
8.4.1. Supported Boards 8.4.2. Steps to Compile the Design Example for Hardware 8.4.3. Steps to Run the Design Example on Hardware
8.4.2. Steps to Compile the Design Example for Hardware x
8.4.2.1. Steps to generate Routing Delay for PTP Enabled Designs
1. Introduction
2. Feature Description
3. Ethernet Subsystem Parameters
4. Subsystem IP Blocks
5. Interfaces and Signals
6. Recommended Clock Connections
7. Register Descriptions
8. Ethernet SS IP Example Design
9. Document Revision History for the Ethernet Subsystem Intel FPGA IP User Guide

4.3.1.11. get_csr for F-Tile

get_csr SAL command is an indirect CSR access to read to HSSI SS CSRs. The CSR address and is written into HSSI Address CSR respectively and then write to HSSI Command/Status CSR to trigger the read CSR operation. The CSR read data is written into HSSI Read Data CSR.

ROffset field in HSSI Command/Status Register is not used and not applicable for F-tile since both Ethernet Reconfiguration Avalon® Mapped-memory and Transceiver Reconfiguration Avalon® Mapped-memory supports 32b access with byte enable.

Refer to set_csr for F-Tile example above to determine the Address[25:2] field in the HSSI Control/Address CS.

RSFEC registers read is per 32 bits,

  • Write HSSI Control/Address Register 0x6 (SAL get_csr Command), 0x0 (Port), 0x0 (Channel), Address[25:2] (RSFEC registers address)
  • Write HSSI Command/Status Register to configure READ_CMD = 1, WRITE_CMD = 0, ROffset = 0 (ignored)
    • Subsystem internally generate single RSFEC register read
  • Read HSSI Command/Status Register ACK_TRANS, BUSY and ERROR
  • If ACK_TRANS = 1 and BUSY/ERROR = 0
  • Read HSSI Read Data [7:0] for RSFEC register data
  • Write 0x0 to clear HSSI Command/Status and HSSI Control/Address
Related Information
Level Two Title