F-tile Architecture and PMA and FEC Direct PHY IP User Guide

ID 683872
Date 10/15/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

8.3. Transceiver Toolkit Parameter Settings

The following table describes the transceiver toolkit parameter settings.
Table 105.  Transceiver Toolkit Parameter Settings
Parameter Description Control Pane
Auto refresh RX CDR status Enable this option to update the RX CDR status real time. Receiver pane.
Auto refresh RX PMA settings Enable this option to update the RX Equalization settings real time for FGT PMA. Receiver pane.
Auto refresh TX Status Enable this option to update the TX PLL lock status real time. Transmitter pane
Bit error rate (BER) Reports the number of errors divided by bits tested since the last reset of the checker. Receiver pane
Clear Stats Clear the current number of bits tested, number of error bits and BER. Receiver pane
Hard PRBS checker running

Red: checker stops.

Green: checker is checking, and data pattern is locked.

Receiver pane
Hard PRBS generator running

Red: generator stops.

Green: generator is sending a pattern.

Transmitter pane
Inject Error Inject a bit error in the transmitter PRBS pattern. Transmitter pane
Line encoding Specifies the modulation type used for serial data. Transmitter and receiver pane
Loopback mode Select the loopbacks mode. Transmitter and receiver pane
Number of bits tested Specifies the number of bits tested since the last reset of the checker. Receiver pane
Number of error bits Specifies the number of error bits encountered since the last reset of the checker. Receiver pane
PRBS locked Green: indicates the PRBS checker is locked to the received PRBS pattern. Receiver pane
PRBS pattern Select the test pattern for the bit error test. Transmitter and receiver pane
RX CDR locked to ref clock Green: Indicates the receiver in lock-to-reference (LTR) mode. Receiver pane
RX CDR locked to data Green: Indicates the receiver in lock-to-data (LTD) mode. Receiver pane
RX Enable Gray Code Enables Gray coding for PAM4 only. Receiver pane
RX PMA Settings RX Equalization settings. There are read-only values. Manual control of the settings in FGT are planned in a future version. Receiver pane
RX Polarity Inversion Enable RX polarity inversion. Receiver pane
RX Ready Green: RX channel out of reset. Receiver pane
RX Reset UX PMA Reset the RX datapath.
Note: Clicking the RX reset of one channel resets all the RX channels in the same F-Tile PMA/FEC Direct PHY Intel® FPGA IP instance.
Receiver pane
Start Starts the pattern generator or checker on the channel to verify incoming data. Transmitter and receiver pane
Stop Stops generating patterns and testing the channel. Transmitter and receiver pane
TX Enable Gray Code Enables Gray coding for PAM4 only. Transmitter pane
TX Equalization Parameters FGT 39 FHT 40 Transmitter pane

M1: Post-cursor 1

C0: Main cursor

P1: Pre-cursor 1

P2: Pre-cursor 2

M3: Pre-cursor 3

M2: Pre-cursor 2

M1: Pre-cursor 1

C0: Main cursor

P1: Post-cursor 1

P2: Post-cursor 2

P3: Post-cursor 3

P4: Post-cursor 4

TX PLL Locked Green: Indicates TX PLL locks to reference clock. Transmitter pane
TX Polarity Inversion Enable TX polarity inversion. Transmitter pane
TX Reset UX PMA Reset the TX PMA datapath.
Note: Clicking the TX reset of one channel resets all the TX channels in the same F-Tile PMA/FEC Direct PHY Intel® FPGA IP instance.
Transmitter pane
39 Refer to F-Tile TX Equalizer Tool for legal settings.
40 Refer to FHT PMA Architecture for legal settings.